NAVY UFGS-08 56 53-2011 BLAST RESISTANT TEMPERED GLASS WINDOWS《防爆钢化玻璃窗户》.pdf

《NAVY UFGS-08 56 53-2011 BLAST RESISTANT TEMPERED GLASS WINDOWS《防爆钢化玻璃窗户》.pdf》由会员分享，可在线阅读，更多相关《NAVY UFGS-08 56 53-2011 BLAST RESISTANT TEMPERED GLASS WINDOWS《防爆钢化玻璃窗户》.pdf（15页珍藏版）》请在麦多课文档分享上搜索。

1、*USACE / NAVFAC / AFCESA / NASA UFGS-08 56 53 (August 2011)-Preparing Activity: NAVFAC SupersedingUFGS-08 56 53 (April 2006) UFGS-08581 (August 2001)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated July 2011*SECTION TABLE OF CONTENTSDIVISION 08 - OPENINGSSECTION 08

2、56 53BLAST RESISTANT TEMPERED GLASS WINDOWS08/11PART 1 GENERAL1.1 REFERENCES1.2 SUBMITTALS1.3 QUALITY ASSURANCE1.3.1 Label1.3.2 Glass and Glazing1.3.3 Independent Testing1.4 DELIVERY, STORAGE, AND HANDLING1.5 ENVIRONMENTAL CONDITIONSPART 2 PRODUCTS2.1 WINDOW UNITS2.2 WEATHERSTRIPPING2.3 GLASS2.4 SET

3、TING MATERIALS2.4.1 Elastomeric Sealant2.4.2 Sealing Tapes, Beads or Gaskets2.4.3 Setting Blocks and Edge Blocks2.4.4 Accessories2.5 WINDOW ASSEMBLIES2.5.1 Provisions for Glazing2.5.2 Sealant, Gaskets, and Beads2.5.3 Weatherstripping2.5.4 Fasteners2.5.5 Drips and Weep Holes2.5.6 Combination Windows2

4、.5.7 Accessories2.5.8 Hardware2.5.9 Anchors2.5.10 Window Cleaner Anchors2.5.11 Finishes2.5.11.1 Anodic Coating2.5.11.2 Organic CoatingSECTION 08 56 53 Page 1Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2.6 SOURCE QUALITY CONTROL2.6.1 Window Assemb

5、ly Structural Test2.6.1.1 Test Sample Number2.6.1.2 Test Procedure2.6.1.3 Acceptance CriteriaPART 3 EXECUTION3.1 INSTALLATION3.1.1 Method of Installation3.1.2 Glass Setting3.1.3 Dissimilar Materials3.1.4 Anchors and Fastenings3.1.5 Adjustments After Installation3.2 CLEANING3.3 SCHEDULE- End of Secti

6、on Table of Contents -SECTION 08 56 53 Page 2Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-*USACE / NAVFAC / AFCESA / NASA UFGS-08 56 53 (August 2011)-Preparing Activity: NAVFAC SupersedingUFGS-08 56 53 (April 2006) UFGS-08581 (August 2001)UNIFIED

7、FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated July 2011*SECTION 08 56 53BLAST RESISTANT TEMPERED GLASS WINDOWS08/11*NOTE: This guide specification covers the requirements for blast resistant tempered glass windows.Adhere to UFC 1-300-02 Unified Facilities Guide Specifica

8、tions (UFGS) Format Standard when editing this guide specification or preparing new project specification sections. Edit this guide specification for project specific requirements by adding, deleting, or revising text. For bracketed items, choose applicable items(s) or insert appropriate information

9、.Remove information and requirements not required in respective project, whether or not brackets are present.Comments, suggestions and recommended changes for this guide specification are welcome and should be submitted as a Criteria Change Request (CCR).*NOTE: Specific details are expanded upon in

10、MIL-HBK-1013/1, Design Guidelines for Physical Security of Fixed Land-Based Facilities.*NOTE: TO DOWNLOAD UFGS GRAPHICSGo to http:/www.wbdg.org/ccb/NAVGRAPH/graphtoc.pdf.*NOTE: On the drawings, show:1. Locations of each type of glass, using same terminology as in the specification.SECTION 08 56 53 P

11、age 3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2. Frame and rabbet details, indicating method of glazing.3. Sizes and types of windows; metal and wood subframes, casings, or stools, if any; and hardware.4. Sizes, location, and swing of ventilat

12、ors; direction of slide for sliding ventilators; location and details of fixed sash.5. Typical window sections and details. Show glass thickness. Show special glazing, if any.6. Method of anchoring windows; size and types of clips, anchors, screws, or other fasteners.7. Details of nonstructural mull

13、ions and mullion covers; detail of anchoring and reinforcing nonstructural mullions at windows to receive window cleaner anchors.8. Number of window cleaner anchors required and locations.9. Locations of windows designated as forced entry resistant, if any.*PART 1 GENERAL1.1 REFERENCES*NOTE: This pa

14、ragraph is used to list the publications cited in the text of the guide specification. The publications are referred to in the text by basic designation only and listed in this paragraph by organization, designation, date, and title.Use the Reference Wizards Check Reference feature when you add a RI

15、D outside of the Sections Reference Article to automatically place the reference in the Reference Article. Also use the Reference Wizards Check Reference feature to update the issue dates.References not used in the text will automatically be deleted from this section of the project specification whe

16、n you choose to reconcile references in the publish print process.*The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text by the basic designation only.SECTION 08 56 53 Page 4Provided by IHSNot for ResaleNo reproduct

17、ion or networking permitted without license from IHS-,-,-ALUMINUM ASSOCIATION (AA)AA DAF45 (2003; Reaffirmed 2009) Designation System for Aluminum FinishesAMERICAN ARCHITECTURAL MANUFACTURERS ASSOCIATION (AAMA)AAMA 2603 (2002) Voluntary Specification, Performance Requirements and Test Procedures for

18、 Pigmented Organic Coatings on Aluminum Extrusions and PanelsAAMA 2604 (2005) Voluntary Specification, Performance Requirements and Test Procedures for High Performance Organic Coatings on Aluminum Extrusions and PanelsAAMA/WDMA/CSA 101/I.S.2/A440 (2008; Update 1 2008; Update 2 2008; Update 3 2009)

19、North American Fenestration Standard/Specification for Windows, Doors, and SkylightsAMERICAN NATIONAL STANDARDS INSTITUTE (ANSI)ANSI Z97.1 (2009; Errata 2010) Safety Glazing Materials Used in Buildings - Safety Performance Specifications and Methods of TestASTM INTERNATIONAL (ASTM)ASTM C1048 (2004)

20、Standard Specification for Heat-Treated Flat Glass - Kind HS, Kind FT Coated and Uncoated GlassASTM C509 (2006; R 2011) Elastomeric Cellular Preformed Gasket and Sealing MaterialASTM C920 (2011) Standard Specification for Elastomeric Joint SealantsGLASS ASSOCIATION OF NORTH AMERICA (GANA)GANA Glazin

21、g Manual (2004) Glazing Manual1.2 SUBMITTALS*NOTE: Review submittal description (SD) definitions in Section 01 33 00 SUBMITTAL PROCEDURES and edit the following list to reflect only the submittals required for the project. Submittals should be kept to the minimum required for adequate quality contro

22、l.A “G” following a submittal item indicates that the submittal requires Government approval. Some submittals are already marked with a “G”. Only delete an existing “G” if the submittal item is not complex and can be reviewed through the Contractors SECTION 08 56 53 Page 5Provided by IHSNot for Resa

23、leNo reproduction or networking permitted without license from IHS-,-,-Quality Control system. Only add a “G” if the submittal is sufficiently important or complex in context of the project.For submittals requiring Government approval on Army projects, a code of up to three characters within the sub

24、mittal tags may be used following the “G“ designation to indicate the approving authority. Codes for Army projects using the Resident Management System (RMS) are: “AE“ for Architect-Engineer; “DO“ for District Office (Engineering Division or other organization in the District Office); “AO“ for Area

25、Office; “RO“ for Resident Office; and “PO“ for Project Office. Codes following the “G“ typically are not used for Navy, Air Force, and NASA projects.Choose the first bracketed item for Navy, Air Force and NASA projects, or choose the second bracketed item for Army projects.*Government approval is re

26、quired for submittals with a “G“ designation; submittals not having a “G“ designation are for Contractor Quality Control approval.for information only. When used, a designation following the “G“ designation identifies the office that will review the submittal for the Government. The following shall

27、be submitted in accordance with Section 01 33 00 SUBMITTAL PROCEDURES:SD-02 Shop DrawingsWindow units; G; G, _Submit drawings indicating elevations of windows, full-size sections, thickness of metal, fastenings, proposed method of anchoring, size and spacing of anchors, details of construction, comp

28、lete details of setting methods and materials for each type of glazing material, details of hardware, mullion details, method and materials for weatherstripping, support conditions for the glass, material and method of attaching subframes, stools, casings, sills, trim, window cleaner anchors, instal

29、lation details, and other related items.SD-03 Product DataWindow units; G; G, _HardwareSetting materialsWeatherstrippingSubmit window frame data for each type and finish.SD-04 SamplesWindow unitsSECTION 08 56 53 Page 6Provided by IHSNot for ResaleNo reproduction or networking permitted without licen

30、se from IHS-,-,-Submit when factory-finished color coating is provided.SD-08 Manufacturers InstructionsGlassSubmit glass manufacturers instructions for setting and sealing materials and for installation of each type of glazing material specified.SD-10 Operation and Maintenance DataWindow units, Data

31、 Package 1; ; G; G, _Submit data package in accordance with Section 01 78 23 OPERATION AND MAINTENANCE DATA.1.3 QUALITY ASSURANCE1.3.1 LabelEach prime window unit shall bear the AAMA Label warranting that the product complies with AAMA/WDMA/CSA 101/I.S.2/A440. Certificates of Compliance attesting th

32、at the prime window units meet the requirements of AAMA/WDMA/CSA 101/I.S.2/A440 will be acceptable in lieu of product labeling.1.3.2 Glass and GlazingProvide materials that are certified to meet ANSI Z97.1 by an independent testing laboratory.1.3.3 Independent TestingTesting shall be performed by an

33、 independent testing laboratory (certified by the Contracting Officer) and test report shall be signed by a registered professional engineer and shall include results from tests in the calculations.1.4 DELIVERY, STORAGE, AND HANDLINGa. Deliver products to the site in unopened containers, labeled pla

34、inly with manufacturers name and brands. Deliver window assemblies in an undamaged condition. Exercise care in handling and hoisting windows during transportation and at the job site. Store windows and components out of contact with the ground, under a weathertight covering, so as to prevent bending

35、, warping, or otherwise damaging the windows.b. Finished surfaces shall be protected during shipping and handling using the manufacturers standard method, except that no coatings or lacquers shall be applied to surfaces to which sealants, caulking, or glazing compounds must adhere.1.5 ENVIRONMENTAL

36、CONDITIONSDo not start glazing work until the outdoor temperature is above 4 degrees C40 degrees F and rising unless approved provisions are made to warm the glass and rabbet surfaces. Provide sufficient ventilation to prevent condensation of moisture on glazing work during installation. Do not SECT

37、ION 08 56 53 Page 7Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-perform glazing work if moisture collects on window assemblies or during rainy weather.PART 2 PRODUCTS2.1 WINDOW UNITSPrimed window frames shall conform to AAMA/WDMA/CSA 101/I.S.2/A44

38、0 and the requirements specified herein. Provide windows of types, grades, performance classes, combinations, and sizes indicated or specified. Provide windows to accommodate hardware, glass, weatherstripping and accessories. Each window shall be a complete factory-assembled unit with glass factory

39、or field installed.2.2 WEATHERSTRIPPINGWeatherstripping shall conform to AAMA/WDMA/CSA 101/I.S.2/A440.2.3 GLASSUse ASTM C1048 and ANSI Z97.1 Grade B (tempered), Style I (uncoated), Type 2, Class 1 (transparent) 2 (heat absorbing).2.4 SETTING MATERIALSProvide types required for the applicable setting

40、 method specified in the GANA Glazing Manual, unless specified otherwise herein. Do not use metal sash putty, non-skinning compounds, nonresilient preformed sealers, or impregnated preformed gaskets. Materials exposed to view and unpainted shall be gray, black or neutral color.2.4.1 Elastomeric Seal

41、antASTM C920, Type S or M, Grade NS, Class 12.5, Use NT. Use for channel or stop glazing and metal sash. Sealant shall be chemically compatible with setting blocks, edge blocks, and sealing tapes. Color of sealant shall be as selected gray black white _.2.4.2 Sealing Tapes, Beads or GasketsGaskets o

42、r beads shall be at least 9.5 mm 3/8 inch wide with a Shore “A“ durometer hardness of 50 and conform to ASTM C509.2.4.3 Setting Blocks and Edge BlocksUse neoprene of 70 to 90 Shore “A“ durometer hardness, chemically compatible with sealants used, and of sizes recommended by the glass manufacturer.2.

43、4.4 AccessoriesUse accessories as required to provide a complete installation, including glazing points, clips, shims, angles, beads, and spacer strips. Provide noncorroding metal accessories. Provide primer-sealers and cleaners as recommended by the glass and sealant manufacturers.2.5 WINDOW ASSEMB

44、LIESWindow units shall conform to AAMA/WDMA/CSA 101/I.S.2/A440.SECTION 08 56 53 Page 8Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2.5.1 Provisions for Glazing*NOTE: Edge clearances, face clearances, and bites shall be maintained as shown below:Minimum Clearance and Bite RequirementsGlass “A“ “C“Thickness Minimum