NAVY MIL-R-60897 (4)-1989 REMOVER AIRCRAFT CANOPY M8A1 METAL PARTS ASSEMBLY (CONVERSION)《 M8A1飞机座舱盖金属装配件清洗剂》.pdf

《NAVY MIL-R-60897 (4)-1989 REMOVER AIRCRAFT CANOPY M8A1 METAL PARTS ASSEMBLY (CONVERSION)《 M8A1飞机座舱盖金属装配件清洗剂》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-R-60897 (4)-1989 REMOVER AIRCRAFT CANOPY M8A1 METAL PARTS ASSEMBLY (CONVERSION)《 M8A1飞机座舱盖金属装配件清洗剂》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-R-60897 (4) 33 9999706 0343954 4 M 1 INCH-WUND I HIL-R-0897(0C) MIENDMENT 4 16 PYIY 1999 SUPERSEDING CIMENDMENT 3 5 DECEMBER 1969 MILITARY SFECIFICCITION REMWER, AIRCRAFT CANOPY tl8AltMETAL . PARTS ASSEMBLY cMJvERSIN) This amendment forms a part of MIL-R-60897(MU), dated 28 June 1968, and is app

2、roved for use by the Naval Sea Systems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense: PAGE 1 * Paragraph 2.1, SPECIFICATIONS, Federal: . Delete QQ-Ei-634 and QQ-S-637 and their titles. PAGE 2 Paragraph 2:l: Delete “C8837891 - B

3、ox, Packing, Ammunition for Remover, Aircraft Canopy, M8 with Cartridge M150“ and substitute “C9230161 - Box, Packing, Ammunition for (1) Remover, Aircraft Canopy M8 and MEA1 with Cartridge Ml50.“ Pew# 3 Paragraph 3.41 Delete in its entirety. * Add Paragraph: “3.5.11 - The remover shall not fail to

4、operate under normal load curve B of fig. 1 at a voltage input of 18 volts d.c. Paragraph 3.6: Delete in its entirety. AMSC N/A FSC 1377 DISTRIBUTIN STATEMENT A. Approved for public release; distribution is un1 i mi ted. Provided by IHSNot for ResaleNo reproduction or networking permitted without li

5、cense from IHS-,-,-MIL-R-hOB97 (4) 33 O 977770b 0343755 b 0 - HIL-R-M)897S) AMENilENT 4 Paragraph 3.7.1 : Delete Whaf t Torque 1 i mit B10522004“ and substi tute “Shaft Torque Limit and Washer Assembly B10522005“. Delete “MS25182-2“ and substi tute MS25181-2. II Delete “Washer, Flat- MS15795-4- i. I

6、I Delete “Screw, Machine-B10522002-1.“ Delete “MS35842-5“ and substi tute “MS35842-13. PAOE b Paragraph 3.7.3, Under New Production Drawing: Delete “FA29985 (P/N FA29985-A)“ and substitute “Spec MIL-1-631. . PAGE 7 Paragraph 3.7.4: Add “Spacer-FA29922. I Delete %crew- FB5 1769. I Delete “MS35377-77“

7、 and substi tute “MS35337-77. PME 9 Paragraph 3.8: Delete in its entirety and substitute Protective Finish shall be in accordance with the applicable specifications and drawings and shall apply to all surfaces of the component regardless of configuration. All manufactured exterior components and com

8、ponents undergoing modification shall have the existing protective finish stripped and the specified protective finish re-applied (see 6.6 through 6.&.5).11 PAGE 23 “3.8 Protective Finish - Paragraph 4,2.2.25: Delete “C8837891“ and substitute “C9230161.“ Paragraph 4.2.3.3: Delete in its entirety. s

9、PAE 24 Paragraph 4.2.3.5: Delete in its entirety. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-i -. Paragraph 4.3.1, Delete in its entirety and substitute: “4.3.1 Hvdrostatic ressure. - Prior to the application o+ protective finish, the outside

10、tube shall be mounted in the test device and subjected to an internal hydrostatic pressure to determine compliance with the requirements of 3.2. The test device used shall internally seal the tube within 1-1/2 inches .o+ the small end and within 2-1/4 inches at the large end without applying an axia

11、l load other than that applied by the liquid pressure.“ Paragraph 4.3.3: Paragraph 4.3.5: Delete in its entirety. Delete in its entirety. PME 25 Paragraph 5.1, line 2: Delete “Drawing C8637891“ and substitute “Drawing C9230 16 1, I PME 26 u Paragraph 6.7.2.1: Delete “QP-S-634“ and substitute WTM-6-1

12、08, Steel Bar, -% .- Carbon, Cold Finished“. u Paragraph 6.7.2.2: Delete “QQ-C-637“ and substitute “ACTM-A-108, Steel Bar, Carbon, Cold Finished“. The margins of this amendment are marked with an asterisk to indicate where changes (additions, modifications, corrections, deletions) from the previous

13、issue were made This was done as a convenience only and the 6overnment assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Preparing activity: NCIVY - os (Project 13774964 1 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-