NAVY MIL-DTL-14803 B-2005 INITIATOR CARTRIDGE ACTUATED DELAY M30A1 M32A1 M92 M43A1 AND M120 REMANUFACTURED METAL PARTS ASSEMBLY《M30A1 M32A1 M92 M43A1和M120型再造金属零件装配延迟弹筒驱动引发器》.pdf

《NAVY MIL-DTL-14803 B-2005 INITIATOR CARTRIDGE ACTUATED DELAY M30A1 M32A1 M92 M43A1 AND M120 REMANUFACTURED METAL PARTS ASSEMBLY《M30A1 M32A1 M92 M43A1和M120型再造金属零件装配延迟弹筒驱动引发器》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-DTL-14803 B-2005 INITIATOR CARTRIDGE ACTUATED DELAY M30A1 M32A1 M92 M43A1 AND M120 REMANUFACTURED METAL PARTS ASSEMBLY《M30A1 M32A1 M92 M43A1和M120型再造金属零件装配延迟弹筒驱动引发器》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、 INCH-POUND MIL-DTL-14803B 25 February 2005 SUPERSEDING MIL-I-14803A 17 March 1992 DETAIL SPECIFICATION INITIATOR, CARTRIDGE ACTUATED, DELAY, M30A1, M32A1, M92, M43A1, and M120 REMANUFACTURED METAL PARTS ASSEMBLY This specification is approved for use by all Departments and Agencies of the Departmen

2、t of Defense. 1. SCOPE 1.1 Scope. This specification covers the requirements for the M30A1, M32A1, M43A1, M92, and M120 Delay Cartridge Actuated Initiator Remanufactured Metal Parts Assembly (see 6.1). 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in section

3、s 3, 4 or 5 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must mee

4、t all specified requirements of documents cited in sections 3, 4 or 5 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent spe

5、cified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS AND STANDARDS MIL-A-2550 Ammunition, General Specification For MIL-STD-1168 Ammunition Lot Numbering and Ammunition Data Card MIL-STD-413 Vis

6、ual Inspection Guide for Elastomeric O-rings Comments, suggestions, or questions on this document should be addressed to Commander, Indian Head Division, Naval Surface Warfare Center, Technical Information Branch (Code 4230), 101 Strauss Avenue, Indian Head, Maryland 20640-5035, or emailed to amanda

7、.pennnavy.mil. Since contact information can change, you may want to verify the currency of this address information using the ASSIST Online database at http:/assist.daps.dla.mil. AMSC N/A FSC 1377 DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited. Provided by IHSNot f

8、or ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-14803B 2 (Copies of these documents are available online at http:/assist.daps.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2.2 Other Gov

9、ernment documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DRAWINGS Naval S

10、urface Warfare Center, Indian Head (CAGE Codes 19200 and 19203) 10520225 Initiator, Cartridge Actuated, Delay, Metal Parts Assembly 8798142 Box, Packing, Ammunition, For Initiator, Cartridge Actuated, Dela y, M10, M30A1, M31, M32A1, M42, M43A1, M72, M92, or M114 8798143 Box, Fiberboard (Inner), Pack

11、ing, Ammunition, For Initiator, Cartridge Actuated, Delay, M10, M30A1, M31, M32A1, M42, M43A1, M72, M92, or M114 9216933 Box, Fiberboard (Outer), Alternative, Packing Ammunition, for Initiator, Cartridge Actuated, Delay, M10, M30A1, M31, M32A1, M42, M43A1, M72, M92, or M114 (Application for copies s

12、hould be addressed to: Commander, Indian Head Division, Naval Surface Warfare Center, Attn: Technical Information Branch (Code 4230), Indian Head, MD 20640-5035.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise sp

13、ecified, the issues of these documents are those cited in the solicitation or contract. AMERICAN NATIONAL STANDARD INSTITUTE/AMERICAN SOCIETY FOR QUALITY ANSI/ASQ Zl.4 Sampling Procedures and Tables for Inspection by Attributes ANSI/ASQ A8402 Quality Management and Quality Assurance - Vocabulary (Co

14、pies of these documents are available online at http:/webstore.ansi.org/ansidocstore/default.asp, or from the American Society for Quality, PO Box 3005, 611 E. Wisconsin Ave., Milwaukee, WI 53201-4606.) 2.4 Order of precedence. In the event of a conflict between the text of this document and the Pro

15、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-14803B 3 references cited herein (except for related specification sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations

16、 unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Materials. All materials used in the manufacture of the initiators shall conform to the specifications referred to on the respective drawings unle ss specific approval in writing covering a departure therefrom has been obtained from

17、 the cognizant Navy design activity prior to manufacture. When alternate materials or methods of manufacture are specified on the drawings, the bidders selections shall be clearly stated in the proposal. 3.2 Hydrostatic pressure. The initiator chamber and cap shall withstand a hydrostatic pressure o

18、f 5500 to 6500 pounds per square inch (psi) for 15 seconds, minimum, without deformation or mechanical failure (see 6.3.1). 3.3 Firing pin release. The firing pin of the assembled initiator, less safety pin, cartridge retainer, and chamber, shall release from the cocked position when the application

19、 of an axial load of 20 to 35 pounds has withdrawn the initiator pin 3/4 inch, maximum (see 4.4.4.2). 3.4 Initiator pin security. The initiator pin of the assembled initiator, less cartridge retainer and chamber, shall not withdraw beyond the safety pin when subjected to an axial load of 200 to 220

20、pounds. Application of the load shall cause no deformation of the safety pin (see 4.4.4.3). 3.5 Protective finish. Protective finish shall be in accordance with the applicable specifications and drawings and shall apply to all surfaces of the component, regardless of configuration. Remanufactured ex

21、terior components shall have the existing protective finish stripped and the specified protective finish reapplied (see 6.3.2). 3.6 Residual magnetism. The metal parts assembly shall not deflect the indicator of the compass more than five degrees in either direction (see 4.5.5). 3.7 Metal parts asse

22、mbly. Parts shall be combined to produce an assembly which conforms to the requirements of the metal parts assembly drawing. All threaded joints shall be assembled handtight. 3.7.1 Integrated plant products. When remanufacturing and loading of assembly is performed in an integrated plant, the metal

23、parts assembly requirement may be waived and the residual magnetism requirement performed on the loaded assembly only. 3.7.2 Threaded component parts. Class 2A or 2B thread gage shall be used on remanufactured component parts inspection versus Class 3A or 3B thread gage required on new hardware for

24、initiators. 3.8 Workmanship. Initiators shall be free of cracks, splits, or other defects which might prevent proper mating with connecting parts or proper functioning of the device. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-14803B 4 3.

25、8.1 Metal defects. All components shall be free from cracks, splits, cold shuts, inclusions, porosity, or any similar defect. 3.8.2 Burr. No part shall have a burr which might interfere with the assembly or function of the item or which might be injurious to personnel handling the item. 3.8.3 Foreig

26、n matter. No part or assembly shall contain chips, dirt, grease, rust, corrosion, or other foreign matter. 4. VERIFICATION 4.1 Classification of inspections. The inspection requirements specified herein are classified as follows: a. Quality conformance inspection (see 4.4) 4.2 Quality assurance term

27、s and definitions. Reference shall be made to ANSI/ASQ A8402 to define the quality assurance terms used. 4.3 Inspections. Inspections shall be in accordance with MIL-A-2550. 4.3.1 Inspection conditions. Unless otherwise specified (see 6.2), all inspections shall be performed under the following cond

28、itions: a. Temperature: Room ambient 68 to 77F b. Altitude: Sea level c. Humidity: 50 percent relative, maximum d. Atmospheric pressure: 14.7 psia 4.4 Quality conformance inspection. 4.4.1 Lot. 4.4.1.1 Submission of product. Unless otherwise specified by the contracting activity, formation, and iden

29、tification of lots shall be in accordance with ANSI/ASQ Z1.4. 4.4.1.2 Size of lot. For the purpose of identification and shipment, the shipping lots of metal parts assemblies shall consist of 600 assemblies, maximum, unless otherwise specified by contract. 4.4.2 Examination. One hundred percent exam

30、ination shall be performed for all critical defects. Examination for major and minor defects shall be performed in accordance with the classification of defects. Four power (4x) magnification may be used for inspection of such defects as burr and foreign matter. When compliance with the applicable r

31、equirement is in doubt as a result of visual examination, the characteristic shall be measured or gaged to determine acceptability. All nonconforming material shall be Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-14803B 5 rejected. 4.4.2.1

32、 Examination of reclaimed parts. Examination of reusable parts, which require no reprocessing, shall be limited to inspection of defects that require visual type inspection. One hundred percent examination shall be performed for all such defects. All nonconforming parts shall be reprocessed or rejec

33、ted. 4.4.2.2 Retainer, Cartridge, Drawing 8594860, covering a detail of Drawing 10520225. Characteristics Defect Method of Inspection Critical 1 Metering slots in base missing Visual Major 101 Pitch diameter of thread, max Gage 102 Minor diameter of thread, max Gage 103 Elongated slots missing Visua

34、l 104 Thread damaged Visual 105 Metal defective Visual 106 Protective finish inadequate or defective Visual 107 Surface finish on internal radius and base improper Visual 108 Burr Visual 109 Foreign matter Visual Minor None defined 4.4.2.3 Chamber, Initiator, Drawing 8594857, covering a detail of Dr

35、awing 10520225. Characteristics Defect Method of Inspection Critical None defined Major 101 Pitch diameter of large thread, min Gage 102 Minor diameter of large thread, min Gage 103 Pitch diameter of small thread, min Gage 104 Major diameter of small thread, min Gage 105 Thread damaged Visual 106 Me

36、tal defective Visual 107 Protective finish inadequate or defective Visual 108 Surface finish, end of gas port, improper Visual 109 Burr Visual 110 Foreign matter Visual Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-14803B 6 Minor None defin

37、ed 4.4.2.4 Cap, Drawing 8595404, covering a detail of Drawing 10520225. Characteristics Defect Method of Inspection Critical 1 Metal defective in mounting flange surface Visual Major 101 Pitch diameter of thread, max Gage 102 Minor diameter of thread, max Gage 103 Thread damaged Visual 104 Metal def

38、ective Visual 105 Protective finish inadequate or defective Visual 106 Burr Visual 107 Foreign matter Visual Minor None defined 4.4.2.5 Pin, Initiator, Drawing 8595403, covering a detail of Drawing 10520225. Characteristics Defect Method of Inspection Critical None defined Major 101 Metal defective

39、Visual 102 Protective finish inadequate or defective Visual 103 Surface finish on body and body groove improper Visual 104 Burr Visual 105 Foreign matter Visual Minor 201 Surface finish improper, except as otherwise classified Visual 4.4.2.6 Housing, Firing Pin, Drawing 8595408, covering a detail of

40、 Drawing 10520225. Characteristics Defect Method of Inspection Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-14803B 7 Critical None defined Major 101 Pitch diameter of internal thread, max Gage 102 Minor diameter of internal thread, max Gag

41、e 103 Pitch diameter of external thread, min Gage 104 Major diameter of external thread, min Gage 105 Thread damaged Visual 106 Metal defective Visual 107 Protective finish inadequate or defective Visual 108 Surface finish of cavity chamfer improper Visual 109 Burr Visual 110 Foreign matter Visual M

42、inor None defined 4.4.2.7 Pin, Firing, Drawing 8595407, covering a detail of Drawing 10520225. Characteristics Defect Method of Inspection Critical None defined Major 101 Metal defective Visual 102 Protective finish inadequate or defective Visual 103 Surface finish improper Visual 104 Burr Visual 10

43、5 Foreign matter Visual Minor None defined 4.4.2.8 Pin, Safety, Drawing 8595405, covering a detail of Drawing 10520225. Characteristics Defect Method of Inspection Critical None defined Major 101 Diameter of wire Measure 102 Profile incorrect Visual Provided by IHSNot for ResaleNo reproduction or ne

44、tworking permitted without license from IHS-,-,-MIL-DTL-14803B 8 103 Metal defective Visual 104 Protective finish inadequate or defective Visual 105 Burr or sharp edges Visual 106 Foreign matter Visual Minor None defined 4.4.2.9 Spring, Initiator, Drawing 8595406, covering a detail of Drawing 105202

45、25. Characteristics Defect Method of Inspection Critical None defined Major 101 Load at specified heights Gage 102 Height of solid, max Gage 103 Ends incorrect Visual 104 Protective finish inadequate or defective Visual 105 Burr or sharp edges Visual 106 Foreign matter Visual Minor 201 Diameter outs

46、ide, closed, max Gage 202 Diameter inside, min Gage 203 Free length Gage 4.4.2.10 Seal, Drawing 10524102, covering a detail of Drawing 10520225. Characteristics Defect Method of Inspection Critical None defined Major 101 Diameter outside, min Gage 102 Width, min Gage 103 Thickness, min Gage 104 Cut,

47、 cracked, or split Visual 105 Flash Visual 106 Foreign matter Visual Minor 201 Diameter outside, max Gage 202 Width, max Gage Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-14803B 9 203 Thickness, max Gage 4.4.2.11 Assembly, Drawing 10520225

48、, less Drawings 8595403, 8595405, 8594857, 8594860 and NAS 832-4. Characteristics Defect Method of Inspection Critical 1 Protrusion of firing pin Gage 2 O-ring missing Visual 3 Steel ball missing Visual Major None defined Minor 201 O-ring not lubricated Visual 4.4.2.12 Assembly, Drawing 10520225. Characteristics Defect Method of Inspection Critical None defined Major 101 Initiator pin not free to rotate Manual 102 Safety pin loose or defo