NAVY MIL-C-24017 B-1985 CARTRIDGE IMPULSE MARK 8 MOD 0《0型8号脉冲炮弹》.pdf

《NAVY MIL-C-24017 B-1985 CARTRIDGE IMPULSE MARK 8 MOD 0《0型8号脉冲炮弹》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-C-24017 B-1985 CARTRIDGE IMPULSE MARK 8 MOD 0《0型8号脉冲炮弹》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-C-Zq017B 13 1111 7777706 030i1230 8 dP-37- /y MIL-C-24017B(AS) 10 December 1985 SUPERSEDING 7 July 1967 MIL-C-24017A(AS) MILITARY SPECIFICATION CARTRIDGE, IMPULSE, MARK 8 MOD O This specification is approved for use within the Naval Air Systems Command, Department of the Navy, and is available f

2、or use by all Departments and Agencies of the Department of Defense. 1. SCOPE p 1.1 Scope. This specification covers the requirements for the manufacture and acceptance of the Mark 8 Mod O Impulse Cartridge (see 6.1). -Il -i. -. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications

3、and standards. The foilowing specifications and standards form a part of this specifica- tion to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and s

4、up- plement thereto, cited in the solicitation. 0 SPECIFICATIONS Military MIL-P-116 Preservation-Packaging, Methods of MIL-D-21625 MIL-1-81530 Design and Evaluation of Cartridges for Cartridge Actuated Devices Ignition Element, Electric, Mark 11 Mod O STANDARDS Military MIL-STD-105 MIL-STD- 129 Samp

5、ling Procedures and Tables for Inspection by Attributes Marking for Shipment and Storage MIL-STD-453 Inspection, Radiographic - Beneficial comments (recommendations, additions , deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commanding Office

6、r, Naval Air Engineering Center, Systems Engineering and Standardization Department (SESD) Code 93, Lakehurst, NJ 08733, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or bv letter. - AMSC N/A THIS DOCUMENT CONTAINS- 9 P

7、AGES -, FSC 1377 DISTRIBUTION STATEMENT A: Approved for public release; distribution is unlimited. I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-C-29037B 33 -7SOb 0304233 T 9 MIL-C-240 17B(AS) 2.1.2 Drawings and publications. The following d

8、rawings and publications form a part of this specifica- tion to the extent specified herein. Unless otherwise specified, the issues shall be those in effect on the date of the solicitation. DRAWINGS Naval Air Systems Command (Code Ident 30003) 2240770 2299605 Container, Inner, for Cartridge Impulse,

9、 Mark 8 Type, Assembly Container, Outer, for Cartridge Impulse, Mark 8 Type, Assembly DL537909 DL546659 PUBLICATIONS Cartridge, Impulse, Mark 8 Mod O Ignition Element, Electric, Mark 11 Type Naval Sea Systems Command (Code Ident 5371 1) OP 5 WR-43 Ammunition and Explosives Ashore Preparation of Qual

10、ity Assurance Provisions Code of Federal Regulations 49 CFR 100-199 Transportation (Copies of specifications, standards, drawings, and publications required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contrac

11、- ting activity). 2.2 Order of Precedence. In the event of a conflict between the text of this specification and the references cited herein (except for associated detail specifications, specification sheets or MS standards), the text of this specification shall take precedence. Nothing in this spec

12、ification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified in the contract or purchase order, a sample shall be subjected to first article inspection (see 4.4 and 6.3). 3.2 Conformance to docume

13、nts. The Mark 8 Mod O impulse cartridge covered by this specification shall be manufactured in accordance with DL537909 and all documents listed thereon. 3.3 Materials. Ail materials used in the manufacture of the cartridges shall conform strictly to the specifica- tions referred to on the respectiv

14、e drawings. When alternate materials or methods of manufacture are specified on the drawings, the bidders selections shall be clearly stated in the proposal. 3.4 Primary components. For the purposes of this specification the Mark 11 Mod O electric ignition ele- ment (DL546659) and the cartridge prop

15、ellant charge are considered primary components. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-VIL-C-24027B I3 m 0b 0304232 I - MIL-C-240 17B(AS) 3.5 Ignition element. The ignition elements shall be furnished from lots which were manufactured wit

16、hin the past 12 months. The ignition elements shall be manufactured in accordance with the drawings listed on DL546659, and shall be from lots which were accepted in accordance with the requirements of MIL- 1-81530 (see 4.6.1). When the same contractor manufactures the Mk 11 Mod O Ignition Element a

17、nd the Mk 8 Impulse Cartridge and assembles the ignition element in the cartridge, the preproduction and produc- tion test requirements of MIL-1-81530 for the ignition element shall be waived. 3.6 Propellant charge. 3.6.1 Quantity. All propellant charges shall be as specified on the applicable drawi

18、ng. Charges shall be determined by weight rather than by volume measurement. 3.6.2 Smokeless powder, handlinp, and loading. The smokeless powder shall be subjected to no unnecessary handling or exposure to the atmosphere. The handling and loading of smokeless powder exposed to the atmosphere shall b

19、e performed only under conditions that do not permit the relative humidity to exceed 75 percent. 3.6.3 Smokeless powder, condition. The smokeless powder used shall exhibit no evidence of decomposi- tion (see 4.6.2) 3.7 Cartridge requirements. 3.7.1 Bridge circuit resistance. The resistance of the br

20、idge circuit in each completely assembled cartridge, when measured electrically (see 4.6.4), shall be not less than 0.08 ohm nor more than 0.15 ohm. 3.7.2 Leakage. Cartridge leakage rate shall be not greater than cubic centimeters of air per second (see 4.6.5). 3.7.3 X-ray. Cartridges shall be free

21、of imperfections when X-rayed (see 4.6.6). 3.8 Ballistic requirements. Cartridges shali meet the ballistic requirements specified in 3.8.1 through 3.8.4 when subjected to the test prescribed in 4.6.7. 3.8.1 Velocity at ejection. The lower limit (LL) of velocity shall be 16.0 feet per second. The upp

22、er limit (UL) of velocity shall be 25.0 feet per second. 3.8.2 Pressure. The lower limit (LL) of pressure shall be 5,200 psi. The upper limit (UL) of pressure shall be 8,700 psi. 3.8.3 Ignition time. The time from the application of firing current to the first indication of pressure rise shall be no

23、t greater than 0.050 second. 3.8.4 Release time. The time from application of firing current to the first indication of hook opening shall be not greater than 0.020 second. firings shall be conducted in accordance with 4.8. 3.9 Change in propellant lot. Whenever a change occurs in the propellant lot

24、 for the main charge, test 3.10 Workmanship. Cartridges shall be free of the following defects: burrs, dents, incomplete or damaged threads, missing or damaged O-ring, perforated closure disc, or other defects which may prevent entry of the cartridge into the firing chamber, or affect the resistance

25、 of the cartridge to moisture (see 4.6.3). 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-240L7B 13 U 7777?70b 0304233 3 W 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purch

26、ase order, the con- tractor is responsible for the performance of ail inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements speci

27、fied herein, unless disapproved by the Govern- ment. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance.

28、 Ail items must meet all requirements of sections 3 and 5. The in- spection set forth in this specification shall become a part of the contractor?s overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the con- tractor of the

29、responsibility of assuring that all products or supplies submitted to the Government for ac- ceptance comply with all requirements of the contract. Sampling in quality conformance does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government

30、 to acceptance of defective material. 4.2 Classification of inspections. The inspection requirements specified herein are classified as follows: a. First article inspection (see 4.4) b. Quality conformance inspection (see 4.5). 4.3 Inspection conditions. Unless otherwise specified (see 6.2), all ins

31、pections shali be performed as specified in the applicable test method of 4.6. 4.4 First article inspection. First article inspection shall be performed after award of contract and prior to production by a facility designated in the contract or order (see 6.2). A first article sample acceptable for

32、environmental and function testing shall be a sample that has met the requirements of 3.2 through 3.7.3 and 3.10 of this specification. First article inspection shall be performed on sample units which have been produced using the same materials, equipment, processes and procedures as will be used i

33、n regular produc- tion. All parts and materials, including packaging and packing shall be the same as used for regular produc- tion and shall be from the intended sources of supply. 4.4.1 Sample size. The first article sample shall consist of 76 cartridges. 4.4.2 Inspection routine. Sixty-six cartri

34、dges shall be expended in the tests listed below and 10 shall be retained for investigative purposes. Testing shail consist of the following tests as prescribed in MIL-D-21625 (see 6.2): 15 ?gYy shock (6); Temperature/humidity cycling THC(18); vibration (6). The number in paren- theses denotes the n

35、umber of cartridges allocated for each test. After exposure to the specified environmen- tal treatment, the cartridges shall be conditioned ?or 12 hours at 70? however, one primary component production lot may be used in more than one cartridge production lot. Cartridges selected for the ballistic t

36、est shall be delivered to the activity designated by the contracting agency, - Sample size Retained sample 15 10 15 10 20 10 25 10 30 10 35 10 40 10 50 10 15 10 4.5.2 Sampling. Unless otherwise specified (see 6.2), sampling shall be in accordance with table II. .A O D 4.5.3 Classification of charact

37、eristics. The characteristics verified by the tests and examinations herein are classified as critical, major, or minor in accordance with WR-43. Tests and examinations that verify critical characteristics are identified by the symbol (C) and major characteristics by the symbol (M). The number follo

38、wing the classification symbol indicates the serial number of the test or examination. Tests and examinations which are not annotated with a classification code are classified minor. TABLE I. Quality conformance tests and examinations. Item Primary component Ignition element Propellant charge Smokel

39、ess powder Cartridge Cartridge Cartridge Cartridge Cartridge Cartridge Cartridge Nature of test Single lot verification Age and acceptance verification Type and weight Condition Visual examination Bridge circuit resistance X-ray Ballistics Leakage Ballistics (change in propellant lot) Preservation-p

40、ackaging, packing and marking Requirement para. 3.4 3.5 3.6.1 3.6.3 3.1.4 3.1.1 3.1.3 3.8 3.1.2 3.9 Section 5 Test para. 4.5.1 4.6.1 4.6.2 4.6.3 4.6.4 4.6.6 4.6.1 4.6.5 4.8 4.6.3 Classification (WR-43) I 4.6 Tests. 4.6.1 Ignition element verification. Verification shall be provided that the ignition

41、 elements used were certified and accepted in accordance with the requirements of 3.5. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-20L7B 13 m 777770b 0304235 7 m I 4.6.2 Smokeless powder, condition. Smokeless powder shall be inspected in

42、accordance with the applicable paragraphs of OP 5. Evidence of decomposition shall be cause for rejection. 4.6.3 Visual examination, All cartridges shall be visually examined. Cartridges having any of the defects of 3.10 shall be cause for rejection. The preservation-packaging, packing, and marking

43、of the cartridges shall be examined for conformance to section 5. 4.6.4 Bridge circuit resistance. Conformance with the bridge circuit resistance of 3.7.1 shall be ascer- tained on all completely assembled cartridges by means of a test circuit which limits the bridge circuit cur- rent to not greater

44、 than 25 milliamperes. A safety chamber with an interlock switch shall be used to protect the operator during the application of current. A suitable instrument which is known to be accurate to within 0.005 ohm in the range of resistance specified shall be used to determine whether or not the require

45、ment is being met. Units which fail to meet the requirements of 3.7.1 shall be cause for rejection. The results of bridge circuit resistance measurements shall not be affected by resistance of the test circuit and connector. 4.6.5 Leakage. Each cartridge in the first article or production sample sha

46、ll be leak tested in a dry gas leak tester. Cartridges which exhibit a leak rate greater than cc per second of air at a pressure dif- ferential of 1 f O. 1 atmosphere shall be considered defective. Cartridges of the first article sample which exhibit a leakage defect shall be cause for rejection. If

47、 the number of cartridges of the production lot sam- ple exhibiting leak defects exceeds an AQL of 2.5 percent defective from table II-A of MIL-STD-105, then a 100 percent leak test of the lot being tested shall be required. Cartridges which exhibit a leak rate greater than that specified above shal

48、l be rejected (see 6.5). 4.6.6 Radiographic examination. All cartridges, in the first article and production test samples, shall be radiographically examined in accordance with MIL-STD-453. Cartridges having any observable imperfec- tions in assembly shall be cause for rejection. The cartridges shal

49、l be positioned on their sides for the most revealing exposure. All cartridges shall be identified with serial numbers prior to examination. The car- tridge serial numbers shall be in consecutive order beginning with the number 001 in each production lot. The cartridges shall be arranged on trays or boards in consecutive numerical order, and each radiograph shall carry a permanent identification of the cartridges displayed thereon. The radiograph identification shall include the complete lo