NAVY A-A-60004-1997 TRUCK LIFT PLATFORM GASOLINE-ENGINE-DRIVEN TELESCOPING BOOM [Superseded NAVY MIL-T-29218 A CANC NOTICE 1 NAVY MIL-T-29218 A NAVY MIL-T-29218]《伸缩吊臂汽油发动机驱动的举高平台车[.pdf

《NAVY A-A-60004-1997 TRUCK LIFT PLATFORM GASOLINE-ENGINE-DRIVEN TELESCOPING BOOM [Superseded NAVY MIL-T-29218 A CANC NOTICE 1 NAVY MIL-T-29218 A NAVY MIL-T-29218]《伸缩吊臂汽油发动机驱动的举高平台车[.pdf》由会员分享，可在线阅读，更多相关《NAVY A-A-60004-1997 TRUCK LIFT PLATFORM GASOLINE-ENGINE-DRIVEN TELESCOPING BOOM [Superseded NAVY MIL-T-29218 A CANC NOTICE 1 NAVY MIL-T-29218 A NAVY MIL-T-29218]《伸缩吊臂汽油发动机驱动的举高平台车[.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、c- A-A-60004 I 7777974 0175852 486 I .: i WCH-POUND A-A40004 Aumst27,1997 SUPERSEDING 29 August 1989 MIL-T-292 18A(YD) COMMERCIAL ITEM DESCRIPTION TRUCK, LIFT, PLATFORM, GASOLINE-EJSJGDIE-DRIVEN, TEL.ESC0PING BOOM The General Services Administration has authorized the use of this commercial item des

2、cription for all Federal agencies. 1. SCOPE. This commercial item description (CID) covers self-propelled personnel, telescopic boom type, aerial work platforms (hereinafter referred to as the work platform). The work plaiform is used for various types of overhead construction and maintenance work 2

3、. CLASSIFICATION. The units are of the following types, as specified (see 7.2): TYPE Type1 - TypeII - TypeIII - TypeIV - TypeV - 40 foot (12.2 metre (m) boom. 60 foot (18.3 m) boom. 80 foot (24.4 m) boom. 90 foot (27.4 m) boom. 100 foot (30.5 m) boom. 3. SALENT CHARACTERISTICS. 3.1 Description. The

4、work platform shall be hydrostatic drive (see 3.10 and 7.2), gasoline- engine- or diesel-engine-driven, four wheels and two axles, two-wheel-driven type. The work platform shall consist of a telescopic boom, with a basket type enclosed platform. The plaiform shall be capable of rotating 360 degrees

5、with a 500-pound (lb) 227 kilogram (kg) rated work load at maximum boom reach, and a chassis. The work platfom shall be provided with, but not limited to: a swing brake, chassis brakes, alternating power supply, two-wheel steering, horn, ground work area controls for all platform functions, and forw

6、ard and reverse speeds. Beneficial comments, recommendations, additions, deletions, clarifications, etc. and any data which may improve this document should be sent to: Commanding Officer (Code 15E2), Naval Construction Battalion Center, 1000 23d Avenue, Port Hueneme, CA 93043-4301, by using the Sta

7、ndardization Document Improvement Proposal D Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 3930 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- A-A-6000 4 w 9997974 0375853 312 = A-A-60004 c 3.2 Standard commercial Drod

8、uct. The work platform shall, as a minimum, be in accordance with the requirements of this CID and shall be the manufacturerYs standard commercial product. Additional or better features which are not specifically prohibited by this CID, but which are a part of the mandacturers standard commercial pr

9、oduct, shall be included in the work pla$orm being furnished. A standard commercial product is a product which has been sold or is being currently offered for sale on the commercial market through advertisements or manufacturers catalogs, or brochures, and represents the latest production model. 3.3

10、 Interchangeability. All units of the same classification furnished with similar options under a specific contract shall be identical to the extent necessary to ensure interchangeability of component parts, assemblies, accessories, and spare parts. 3.4 Safetv. An emergency engine shutdown shall be p

11、rovided for the operator. An electric- driven pump shall be provided to allow emergency use of hydraulic system. A1 moving parts and all parts subject to high operational temperatures that are of such a nature or so located as to become a hazard to the operating personnel shall be insulated, enclose

12、d, or guarded to the extent necessary to eliminate the hazard. When incorporated by the manufacturers design, a manual descent valve shall be provided for lowering and retracting boom simultaneously and shall be in easy reach of the ground. All safety and warning devices shall comply with ANSI A92.5

13、 requirements. An alarm shall be installed at the work platform which will be activated automatically when the machine base is more than 5 degrees out of level in any direction. Pilot- operated holding valves shall be provided in the lift cylinders to prevent uncontrolled descent in the event of hos

14、e or hydraulic failure. 3.5 Engine. The manufacturers standard commercial, gasoline or diesel engine shall be furnished. The engine shall be complete with a 12-volt (V) starting and charging system. An air cleaner shall be provided. The power and speed rating of the engine shall be such that the ope

15、ration of the work platfom under any of the requirements or conditions specified herein will not be greater than the engine manufacturers published maximum horsepower. A spark arresting maer shall be provided. The muffler shall direct noise and exhaust hes away from the operator, however, exhaust no

16、ise and fumes shall not effect or interfere with an operator at the ground control panel. The manufacturers standard commercial storage batery normally furnished to make a complete electrical system shall be furnished. When specified (see 7.2), batteries furnished shall be dry charged and moisture s

17、ealed to prevent intrusion of atmospheric moisture. Electrolyte shall not be furnished. 3.6 Fuel tank. The fuel tank shall have sufilCient capacity to operate the work platform for not less than eight hours. 3.7 Steering. The steering shall be of the two-wheel type and shall be controlled from the w

18、ork platfoxm. 3.8 Chassis brakes. The work platform shall be provided with automatic spring-applied, hydradically released brakes on not less than two wheels. The brakes shall be designed to hold the work platorm in the maximum grade for which the platform was designed to negotiate. 2 Provided by IH

19、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-! I A-A-60004 = 993997U OL75854 259 D A-A40004 3.9 Ground controls. A control panel shall be located at the base work platform for ground control operation for all powered functions of the work platform. Ground contr

20、ols shall be provided for lift, telescopic boom swing, rotation of basket work area, engine off and start, platfodground control selector switch, and platform leveling or tilting control. 3.10 Chassis drive. Unless otherwise specified (see 7.2), the chassis shall be hydrostatically driven. When spec

21、ified (see 7.2), the chassis shall be hydraulically driven. The chassis shall be capable of forward and reverse movement. Type I work platforms shall be self-propelled up to 3 miles per hour (4.83 kilometre per hour (km/h) travel speed. Types II, m, IV, and V shall be self-propelled from 2.5 to 4 mi

22、les per hour (4.02 km/h to 6.44 km/h) travel speed. 3.1 1 Hydraulic svstem. The main pump shall have afilter and shall be engine driven with an operating pressure as specified by the manufacturer for the type work platform fimished. 3.12 Electrical svstem. When specified (see 7.2), an electrical sys

23、tem for work platform electrification shall be provided. An electrical materials shall bear the Underwriters Laboratories (UL) listing mark and be listed in the UL Electrical Construction Materials Directory. All electrical equipment and receptacles shall be connected to a 120V, 60 Hertz, 2-pole, 3-

24、wire, ground, single phase power provided by the manufacturers standard generator. All wiring and equipment shall be provided with over-current circuit breaker protection. Ail duplex receptacles shall be hospital grade. All distribution wiring shall be adequately supported and protected with grommet

25、s wherever passing through sheet metai, supports, or framework. Ail receptacles provided with the work platform shall be weatherproof and shall have ground-fault protection. A receptacle shall be provided in the work platform area. 3.13 Outrianers. Outriggers or powered extendible des may be provide

26、d to meet the stability requirements specified herein. 3.14 Wheels and tires. The work platform shall be mounted on four wheels of the manufacturers current standard type and size. The tires shall be pneumatic or polyurethane- filled, as specified (see 7.2). The tires shall have individual rated loa

27、d capacities equal to the maximum tire loading imposed by the operation. When tube type tires are furnished, tubes shall be of heavy-duty type and shall be of proper size for tires. 3.15 Horn. The work platform shall be equipped with an electrical horn with push button located in the work platform.

28、The horn shall be protected against moisture and adverse weather conditions. 3.16 Platform. The platform shall be hydraulically controlled and shall be elevated by a telescoping boom. The platform shall be automatically self-leveling and shall be able to rotate not less than 160 degrees. The platfor

29、m shall contain all operating controls to allow the operator to perform all finctions. These shall include work platform drive (forward, reverse movement, and braking), platform lift and lower, boom extension and retraction; 360 degrees continuous turntable swings (either direction), and start and s

30、top engine. The platform area shall be provided 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-LaO4 U! 51939974 0175855 195 I A-A-60004 with emergency shutdown devices, and deadman control that must be depressed before operator control can be

31、activated. 3.17 Boom. The boom shall be of the telescoping type with a swing of 360 degrees. Rated work load shall be not greater than 500 Ib (227 kg). Work loads are rated with work platform positioned on level ground and boom at maximum reach. The boom, when fully extended, shall , be capable of r

32、eaching a platform height of 40 feet (12.2 m) for type I, 60 feet (18.3 m) for type i& 80 feet (24.4 m) for type III, 90 feet (27.4 m) for type IV, and 100 feet (30.5 m) for type V. The boom shall be provided with a swing brake and shall operate smoothly. The boom shall have 360 degrees continuous t

33、urntable swing in either direction. When the rated work load varies according to multiple configurations of the work plaorm, the manufacturer shall clearly describe these configurations, including the rated work load of each on the work platform. 3.18 Cleaning. treatment. and painting. Surfaces norm

34、ally painted in good commercial practice shall be cleaned, treated, and painted as specified herein. Surfaces to be painted shall be cleaned and dried to ensure that they are free from contaminants such as oil, grease, welding slag and spatter, loose mill scale, water, dirt corrosion product, or any

35、 other contaminating substances. As soon as practicable after cleaning and before any corrosion product or other contamination can result, the surfaces shall be prepared or treated to ensure the adhesion of the coating system. The painting shall consist of at least one coat or primer and one finish

36、coat of acrylic-based or polyurethane enamel. The primer shall be applied to a clean, dry surface as soon as practicable after cleaning and treating. Painting shall be with manufacturers current materials according to manufacturers current processes and the total dry film thickness shall be not less

37、 than 2.5 mils over the entire surface. The paint shall be free from runs, sags, orange peel, or other defects. The end item, allied equipment, and attachments shall be the same color. 3.19 Nameplate. A nameplate will be furnished by the contracting officer for each work platform. The contractor sha

38、ll stamp all necessary data in the blank spaces provided for that purpose and securely &ix it to each work platform in a conspicuous place with nonferrous metal screws, bolts, or rivets not less than O. 125-inch (3 millimetre (mm) in diameter shall be used to affix the plate to the equipment. 3.20 I

39、nstruction plates. The unit shall be equipped with instructions plates suitably located, describing any special or important procedures to be followed in operating and servicing the equipment. Plates shall be of a material which will last and remain legible for the life of the equipment. Plates shal

40、l be securely affixed to the equipment with nonferrous screws or bolts or not less than O. 125-inch (3 mm) in diameter. 3.21 Identification marking. Identification shall be permanently and legibly marked directly on the unit or on a corrosion-resisting metal plat securely attached to the unit at the

41、 source of manufacture. Identification shall include the manufacturers model and serial number, name and trademark to be readily identifiable to the manufacturer. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-60004 999977Q.0375856 O21 = A-A-6

42、0004 3.22 WorkmanshiD. 3.22.1 Steel fabrication. The steel used in fabrication shall be free from kinks, sharp bends, and other conditions which would be deleterious to the finished product. Mandaduring processes shall not reduce the strength of the steel to a value less than intended by the design.

43、 Manufacturing processes shall be done neatly and accurately. Ail bends shall be made by controlled means to ensure uniformity of size and shape. 3.22.2 Castings. All castings shall be sound and free from patching, misplaced wring, warping, or any other defect which reduces the castings ability to p

44、erform its intended function. 3.22.3 Bolted connections. Bolt holes shall be accurately punched or drilled and shall have the burrs removed. Washers or lockwashers shall be provided in accordance with good commercial practice, and all bolts, nuts, and screws shall be tight. 3.22.4 Riveted connection

45、s. Rivet holes shall be accurately punched or drilled and shall have the burrs removed. Rivets shall be driven with pressure tools and shall completely fill the holes. Rivet heads, when not countersunk or flattened, shall be of approved shape and uniform size for the same diameter or rivet. Rivet he

46、ads shall be full, neatly made, concentric with the rivet holes, and in full contact with the surface of the member. 3.22.5 Welding. Welding procedures shall be in accordance with a nationally recognized welding code. The surface of parts to be welded shall be free from rust, scale, paint, grease, o

47、r other foreign matter. Welds shall be of sufficient size and shape to develop the full strength of the parts connected by the welds. Welds shall transmit stress without permanent deformation or failure when the parts connected by the weld are subjected to proof and service loadings. Copies of welde

48、r qualification record shall be made available to authorized Government inspectors. 4. REGULATORY REQUIREMENTS. 4.1 Materials. The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation

49、(FAR). Unless otherwise specified herein, all equipment, material, and articles incorporated in the work covered by this commercial item description are to be new and fabricated using materials produced from recovered materials to the maximum extent possible without jeopardizing the intended use. The term “recovered materials” means materials which have been collected or recovered from solid waste and reprocessed to become a source of raw materials, as opposed to virgin raw mater