GSA A-A-2484-1988 SCREWDRIVER FLAT TIP《一字螺丝刀》.pdf

《GSA A-A-2484-1988 SCREWDRIVER FLAT TIP《一字螺丝刀》.pdf》由会员分享，可在线阅读，更多相关《GSA A-A-2484-1988 SCREWDRIVER FLAT TIP《一字螺丝刀》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、A-A-2484 51 7777774 0042837 b H y- 07-07 A-A-2484 August 15, 1988 COMMERCIAL ITEM DESCRIPTION SCREWDRIVER, FLAT TIP (NONSPARKING AND NONMAGNETIC) The General Services Administration has authorized the use of this commercial item description. This commercial item description covers screwdrivers with

2、plastic handles and fixed flat tip blades made of a nonferrous alloy having a low sparking hazard and a low magnetic permeability. Salient characteristics: Handle. The- handle shall be made of a clear amber or yellow plastic, suitably shaped to fit the hand comfortably and provide a nonslip grip. Di

3、mensions shall be the same as for comparable size screwdrivers with steel blades. Blade. The screwdriver blade shall be made of beryllium copper or aluminum bronze alloy having an iron content not over five percent, and when present, it shall be well diffused throughout the alloy. When tested with a

4、 magnetic permeability indicator conforming to Military Specification MIL-1-17214, the magnetic permeability shall not be above 1.2 on the indicator scale. The screwdriver tip shall be of either the straight or flared flat tip design for driving slotted head screws. The opposite end shall be designe

5、d to be securely mounted in the handle. The blade cross section shall have a diameter or width across flats approximately equal to the screwdriver tip width. Blade tip width and thickness, and lengths (outside of handle) shall be as shown in the following table. Tolerances shall be plus 1/32, minus

6、1/64 inch for tip widths, plus .007 or minus .002 inch for tip thickness, and plus or minus 1/4 inch for blade length. The included angle between bearing surfaces shall be 18 degrees maximum. National Stock Blade Tip Tip Tors i on Width Thickness Moment (Inch 1 ( Inch ) (In.-Lbs. - ) Number Length -

7、ANSNI i I nches ) 5120-00-236-2132 5120-00-561-8021 5120-00-877-8806 5120-00-618-4915 5120-00-203-9588 5i20-00-293-i608 5120-00-287-2502 5120-00-287-2503 3 4 6 6 6 8 12 3-3/4 9/32 1/4 1/8 1/8 3/16 5/16 3/8 3/8 0.032 0.837 0.020 0.020 0.032 0.042 0.050 0-050 35 30 4 4 15 60 110 110 Torsion loads. Eac

8、h screwdriver shall be capable of -withstanding a minimum torsion load as shown in the above table without sustaining deformation or other defects which might affect the durability or serviceability of the screwdriver. Workmanship. Screwdrivers shall be smoothly finished and free from burrs and roug

9、h edges. Blades shall be assembled to the handles securely and in proper alignment. Blade tips shall be symmetrical. FSC 5120 PISTRIBUTION STATEMENT A. Approved for public release; disstribution is unlimited. P -. THIS DOCUMENT CONTAINS 2 PAGES. Provided by IHSNot for ResaleNo reproduction or networ

10、king permitted without license from IHS-,-,- A-A-248Y 51 m 7777774 O042838 8 m A-A-2 4 84 Marking. Each screwdriver shall be marked in a plain and permanent manner *with name, abbreviation, or chemical symbol of the alloy, the manufacturers name or trademark of such known character that the source o

11、f manufacture may be readily determined, and the country of origin. Quality assurance provisions. Sampling for inspection shall be in accordance with MIL-STD-105, Sampling Procedures and Tables for Inspection by Attributes, except where otherwise indicated herein. The lot size shall consist of all s

12、crewdrivers offered for acceptance at one time. A sample unit shall be one screwdriver. A. Examination for design, dimensions and workmanship. The inspection level shall be S-2 with an acceptable quality level (AQL) of 4.0 percent defective. B. Material. Material shall be ascertained by manufacturer

13、s certification. C. Torsion moment test. Torsian moment testing shall be in conformance with commercially accepted procedures. The inspection level shall be S-2 with an AQL of 4.g percent defective. Requlatory requirements. The offerer/contractor is encouraged to use recovered materials in accordanc

14、e with Public Law 94-580, as amended, to the maximum extent practicable. Preservation, packaging, packing, labeling, and marking, The preservation, packag- ing, packing, labeling, and marking shall be as specified in the contract or order. Notes: The issue of referenced documents in effect on the da

15、te of invitation for bid or request for proposals shall be used to determine compliance with the stated requirements. Sources or obtaining referenced documents may be determined bly contacting the Contracting Officer. MILITARY INTERESTS: NONE: DoD has determined that no military activity has an official interest in this commercial item descrition. PREPARING ACTIVITY: GSA-FSS 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-