FORD WSS-M1H1091-A-2016 FABRIC QUEBEC MEDIUM DARK DOVE PATTERN WOVEN TO BE USED WITH FORD WSS-M99P1111-A .pdf

《FORD WSS-M1H1091-A-2016 FABRIC QUEBEC MEDIUM DARK DOVE PATTERN WOVEN TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享，可在线阅读，更多相关《FORD WSS-M1H1091-A-2016 FABRIC QUEBEC MEDIUM DARK DOVE PATTERN WOVEN TO BE USED WITH FORD WSS-M99P1111-A .pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions2006 08 14 Activated L. Neves Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 1 of 2 FABRIC, QUEBEC MEDIUM DARK DOVE PATTERN, WOVEN WSS-M1H1091-A 1. SCOPEThe material defined by this specification is a woven po

2、lyester fabric.2. APPLICATIONThis specification was released originally for material used as an interior trim fabric for BV 256 - 2007 ModelYear.3. REQUIREMENTSMaterial specification requirements are to be used for initial qualification of materials.In addition to the requirements listed herein, the

3、 fabric shall meet all requirements ofWSS-M8P18-A1/A2/A3/A4 as applicable.3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements for Production Materials (WSS-M99P1111-A). 3.2 FABRIC CONSTRUCTION 3.2.1 Fabric Count,

4、 +/- 5% tolerance (ASTM D 3775) Warp 29 yarn/cmFill 18 yarn/cm3.2.2 Fabric Weight, +/- 5% tolerance (FLTM BN 106-01) Seat (laminated to 4 mm foam) 400 g/m Door Panel (laminated to 2 mm foam) 400 g/m 3.3 COMPOSITION (ASTM D 629) Fabric 100% Polyester Foam PUR/Polyester Backing Fabric (Seats only) 100

5、% Polyester Non Woven (Door Panels only) 100% Polyester NOT TO BE USED FOR NEW DESIGN2016 N Status No longer used D. Murtonen, NA 05 05ENGINEERING MATERIAL SPECIFICATIONWSS-M1H1091-A Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 2 of 2 3.4 YARN CONSTRUCTION (ASTM

6、 D 1244) Warp 334 dtex, f 48, Semi Dull, Round, Textured PolyesterFill 500 dtex, f 68, Brilliant, Round, Textured Polyester 3.5 METHOD OF DYEING Warp Yarn Dyed Fill Solution Dyed 3.6 FINISHING OPERATIONS Warp, Wash, Heat Set 3.7 THICKNESS, mm, (ASTM D 1777) Seat (laminated to 4 mm foam + backing fab

7、ric) 3.0 - 4.0 mm Door Panel (laminated to 2 mm foam + non woven) 1.5 - 2.5 mm 3.8 TRIMMABILITY PROPERTIES 3.8.1 Stretch, %, range (SAE J855)Seat and Door Panel Warp 5% Fill 3% 3.9 FLAMMABILITY (ISO 3795/SAE J369) Burn Rate, max 100 mm/minute 4. GENERAL INFORMATIONThe information given below is provided for clarification and assistance in meeting the requirements of thisspecification.4.1 Purchase departments will ensure that material defined in this specification and shipped to anyone assembly plant will be produced by one supplier only.