FORD WSS-M1H1079-A11-2016 FABRIC MATCHPOINT PATTERN WARP KNIT 100% VIRGIN WITH SOIL REPELLANT TO BE USED WITH FORD WSS-M99P1111-A .pdf

《FORD WSS-M1H1079-A11-2016 FABRIC MATCHPOINT PATTERN WARP KNIT 100% VIRGIN WITH SOIL REPELLANT TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享，可在线阅读，更多相关《FORD WSS-M1H1079-A11-2016 FABRIC MATCHPOINT PATTERN WARP KNIT 100% VIRGIN WITH SOIL REPELLANT TO BE USED WITH FORD WSS-M99P1111-A .pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 0 2016 10 17 Released D. Murtonen, NA Controlled document at www.MATS Copyright 2016, Ford Global Technologies, LLC Page 1 of 3 FABRIC, MATCHPOINT PATTERN, WARP KNIT, WSS-M1H1079-A11 100% VIRGIN WITH SOIL REPELLANT FABRIC, MATCHPOINT PAT

2、TERN, WARP KNIT, WRS-M1H1079-A21 RECYCLED, PIR/PCR CONTENT WITH SOIL REPELLANT 1. SCOPE The materials defined by these specifications are a warp knit polyester face fabric embossed, with the base being View. Made from 100% virgin yarn or a minimum of 25% recycled content PIR/PCR (post industrial/pos

3、t consumer) recycled yarn. 2. APPLICATION This specification was released originally for material used as an interior trim fabric for Fieata 2013.5 MCA MY seat insert. The fabric was originally approved as plate embossed tri-laminated with foam and a backing scrim. 3. REQUIREMENTS 3.1 APPROVED SOURC

4、ES This specification requires the use of approved sources. Only the sources identified on the Ford Approved Source List (ASL) can be used when this specification is listed on the drawing, CAD file, or other documents. The list of approved sources is located within Ford at or available externally t

5、hrough a Ford Materials Engineer. 3.2 APPPEARANCE The color, pattern, and finish shall match the approved Corporate Design master sample. 3.3 FABRIC PERFORMANCE In addition to the requirements listed herein, the fabric shall meet all requirements of WSS-M8P18-B1/B2/B3/B4/latest as applicable. 3.4 VE

6、HICLE INTERIOR ENVIRONMENTAL PERFORMANCE Materials used in interior applications must meet the requirements outlined in WSS-M99P2222-D1/latest, Performance, Vehicle Interior Environmental Quality Material/Component Requirements. Data must be included in material submission package. 3.5 CONDITIONING

7、AND TEST CONDITIONS All test values are based on material conditioned for not less than 24 h prior to testing in a controlled environment of 23 +/- 2 C and 50 +/- 5% relative humidity. Testing of the material should occur in the conditioning environment or soon after removal. 3.6 FABRIC CONSTRUCTION

8、 3.6.1 Fabric Count, -/+5 % tolerance ENGINEERING MATERIAL SPECIFICATION WSS-M1H1079-A11 WRS-M1H1079-A21 Copyright 2016, Ford Global Technologies, LLC Page 2 of 3 (ASTM D3775) Wales 130/ 10 cm Courses 240 / 10 cm 3.6.2 Fabric Weight, -/+5 % tolerance 260 g/m2 (FLTM BN 106-01) 3.7 COMPOSITION (ASTM D

9、629) Fabric 100% polyester 3.8 YARN CONSTRUCTION (ASTM D1244) Face (A) 78 Dtex f36, (polyester, false twist, texturized) Face (B) 76Dtex f24, (yarn type i.e. polyester, false twist) A11 A21 Back 76 Dtex f24 76 Dtex f24 (polyester flat yarn) (yarn type i.e. polyester flat yarn with 100% recycled yarn

10、) 3.9 RECYCLED CONTENT Recycled yarn must contain a minimum of 25% recycled content PIR/PCR (Postindustrial/post consumer) as defined by WRS-M99P42-A2. The remaining portion of the material can come from virgin sources. Refer to the Approved Source List (ASL), for specific regional recycled levels f

11、or this material. 3.10 METHOD OF DYEING Solution dyed 3.11 FINISHED OPERATIONS Washing, drying,soil repellent finish, framing, plate embossed Any changes to the above process must be approved by Materials Engineering. ENGINEERING MATERIAL SPECIFICATION WSS-M1H1079-A11 WRS-M1H1079-A21 Copyright 2016,

12、 Ford Global Technologies, LLC Page 3 of 3 4. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Specifications. 4.1 Purchase departments will ensure th

13、at the material defined in this specification and shipped to any one assembly plant will be produced by one supplier only. In the event of a Global Program or Regional duplication, each regional location of the supplier for this specification must provide a Construction package and be approved to me

14、et this specification. 4.2 If yarn is locally sourced it must meet the above fabric construction, composition and yarn construction. The fabric must also meet the requirements of WSS-M8P18-B1/B2/B3/B4/latest. 4.3 Global strategy for this fabric is to use tri-laminate/foam & scrim construction in all

15、 regions. 4.4 APPROVAL OF MATERIALS Suppliers desiring approval of their materials shall first obtain an expression of interest from Purchasing, Design or Product Development, and Materials Engineering. The supplier shall submit a completed copy of their laboratory test reports, signed by a qualifie

16、d and authorized representative of the test facility, demonstrating full compliance with all the requirements of the Material Specification. Tested material samples must be available for review upon request and kept for a minimum of one year. Upon request, the supplier will review the associated qua

17、lity control documents (Process Failure Mode and Effects Analysis, Control Plans, Certification testing) with Ford. 4.5 SUPPLIERS ONGOING RESPONSIBILITY All materials must be equivalent in all characteristics to the material upon which approval was originally granted. Prior to making any changes to

18、the material originally approved, whether or not such changes affect the materials ability to meet the specification requirements, the supplier shall notify the affected Supplier Technical Assistance (STA), Purchasing, and Materials Engineering activities of the proposed changes (with reasons) by su

19、bmission of a completed Suppliers Request for Engineering Approval, SREA. For parts and components using Ford Engineering Material Specifications, all samples tested to the specifications for Design Verification (DV), Production Verification (PV) and Producation Part Approval Process (PPAP) sign off

20、 must be kept until Job 1. 4.6 RESTRICTED SUBSTANCE MANAGEMENT STANDARD Substance restrictions imposed by regulations or Company direction applies to the materials addressed by this document. The restrictions are identified in the Restricted Substance Management Standard WSS-M99P9999-A/latest which is updated yearly. It is the suppliers responsibility to comply with this standard on a continuing basis. 5. SUMMARY OF REVISIONS