FORD WSL-M99G163-A1-2006 INSULATOR HEAT SHIELD SILICONE FOAM FIBERGLASS MAT TO BE USED WITH FORD WSS-M99P1111-A 《硅酮泡沫塑料、纤维玻璃毡片挡热绝热材料 与标准FORD WSS-M99P1111-A一起使用 使用标准WSS-M99P32-B.pdf

《FORD WSL-M99G163-A1-2006 INSULATOR HEAT SHIELD SILICONE FOAM FIBERGLASS MAT TO BE USED WITH FORD WSS-M99P1111-A 《硅酮泡沫塑料、纤维玻璃毡片挡热绝热材料 与标准FORD WSS-M99P1111-A一起使用 使用标准WSS-M99P32-B.pdf》由会员分享，可在线阅读，更多相关《FORD WSL-M99G163-A1-2006 INSULATOR HEAT SHIELD SILICONE FOAM FIBERGLASS MAT TO BE USED WITH FORD WSS-M99P1111-A 《硅酮泡沫塑料、纤维玻璃毡片挡热绝热材料 与标准FORD WSS-M99P1111-A一起使用 使用标准WSS-M99P32-B.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2006 05 05 N-STATUS Replaced by WSS-M99P32-B; Ins 3.0; Del 3.1, 3.2, 3.3, 3.7, 3.8 & 4 A. Reaume 1991 10 22 NL00E10054111 Revised 3.5.5, updated para 4 L. Gullen 1990 11 06 NL00E10054111 Released L. Gullen, R. Fekete Printed copies are uncontr

2、olled Copyright 2006, Ford Global Technologies, LLC Page 1 of 2 INSULATOR, HEAT SHIELD, SILICONE FOAM, FIBERGLASS MAT WSL-M99G163-A1 NOT TO BE USED FOR NEW DESIGN 1. SCOPE This specification covers a low density modified closed cell silicone foam cast directly onto silicone impregnated fiberglass ma

3、t without the use of adhesives. A second fiberglass mat may be applied to the cast foam as required. The material is self extinguishing, has low compression set and is suitable in static applications from -55 C to 260 C. 2. APPLICATION This specification was released originally for fuel tank heat sh

4、ield applications. 3. REQUIREMENTS Material specification requirements are to be used for initial qualification of materials. 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P

5、1111-A). 3.4 DYNAMIC MECHANICAL ANALYSIS (ASTM D 4065) Ford Motor Company, at its option, may establish a shear modulus/damping vs. temperature curves plotted for -50 to +150 C temperature range for material/parts supplied to this specification. The shear modulus and damping curves established for i

6、nitial approval shall constitute the reference standard and shall be kept on file at the designated material laboratory. All samples shall produce shear modulus and damping curves that correspond to the reference standard when tested under the same conditions. 3.5 REQUIREMENTS FOR SILICONE FOAM 3.5.

7、1 Density, max 256 kg/m3Density shall be determined by cutting a 150 x 150 +/- 0.8 mm specimen and weighing it to +/- 0.25 grams. Thickness shall be determined with a dial micrometre having minimum pressure foot diameters of 25 mm or similar averaging procedure. Density shall be calculated as follow

8、s: Density Kg/m3= weight (in grams) (thickness, in mm x 12.5) ENGINEERING MATERIAL SPECIFICATIONWSL-M99G163-A1 Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 2 of 2 3.5.2 Tensile Strength, min 140 kPa (ASTM D 412) Elongation, min 60% 3.5.3 Compression/Deflection,

9、max 42 kPa (25% deflection at 2.5 mm/minute) 3.5.4 Compression Set, max 35% (ASTM D 395, 50% for 22 h at 100 C) 3.5.5 Accelerated Aging Bend 180, no cracks, surface (ASTM D 573, 72 h at tackiness or charring 230 +/- 2 C) 3.5.6 Low Temperature Test, 10% max thickness change (ASTM D 1056) 3.5.7 Flamma

10、bility (ISO 3795/SAE J369) Burn Rate 100 mm/minute 3.5.8 Volatile Silicones, max 0.65% (FLTM AV 102-01) 3.6 REQUIREMENTS FOR FIBERGLASS MAT 3.6.1 Breaking Strength (ASTM D 1682, para 12, Method Grab and Modified Grab) Warp Direction, min 45 N/mm (25 mm clamp, 25 mm wide strip) Fill Direction, min 25 N/mm 3.6.2 Density, max 256 Kg/m33.6.3 Flammability (ISO 3795/SAE J369) Burn Rate, max 100mm/minute