FORD WRS-M1H1239-A1-2016 FABRIC LEGEND PATTERN FLAT WOVEN 25% PIR UNLAMINATED TO BE USED WITH FORD WSS-M99P1111-A .pdf

《FORD WRS-M1H1239-A1-2016 FABRIC LEGEND PATTERN FLAT WOVEN 25% PIR UNLAMINATED TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享，可在线阅读，更多相关《FORD WRS-M1H1239-A1-2016 FABRIC LEGEND PATTERN FLAT WOVEN 25% PIR UNLAMINATED TO BE USED WITH FORD WSS-M99P1111-A .pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev 01 2016 07 25 N Status Replaced by WRS-M1H1239-A23 D. Murtonen, NA 2013 05 10 Released M. Dumitrescu, NA Copyright 2016, Ford Global Technologies, Inc. Page 1 of 2 FABRIC, LEGEND PATTERN, FLAT WOVEN WRS-M1H1239-A1 25% PIR UNLAMINATED NOT

2、TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a woven dobby face fabric. The fabric is made with 25% PIR (Post industrial) recycled yarn. 2. APPLICATION This specification was released originally for material used as an interior trim fabric for F-Series 2016 seat i

3、nsert. The fabric was approved as backcoated. 3. REQUIREMENTS 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). Materials with recycled content as defined by WRS-M99P4

4、2-A2 (Textile Materials, Identification of Recycled Content) should be used whenever technically feasible. 3.1.1 This specification must contain 25% recycled content as defined by WRS-M99P42-A2. The remaining portion of the material can come from virgin sources 3.1.2 In addition to the requirements

5、listed herein, the fabric shall meet all requirements of WSS-M8P18-A1/A2/A3/A4 as applicable. 3.2 FABRIC CONSTRUCTION 3.2.1 Fabric Count, +/- 10% tolerance (ASTM D 3775) Warp 260 ends/10 cm Weft 200 picks/10 cm 3.2.2 Fabric Weight, +/-10 % tolerance, (FLTM BN 106-01) Face fabric 350 g/m2 Backcoat/Re

6、sin 43 g/m2 Total weight 393 g/m2 3.3 COMPOSITION (ASTM D 629) Fabric 100% Polyester Backcoating Acrylic ENGINEERING MATERIAL SPECIFICATION WRS-M1H1239-A1 Copyright 2016, Ford Global Technologies, Inc. Page 2 of 2 Tolerance as specified in WSS-M8P18-A1/A4 3.4 YARN CONSTRUCTION (ASTM D 1244) Warp 115

7、0 dtex (solution dye polyester yarn) 370 dtex (100% recycled solution dye polyester yarn) Weft 370 dtex (100% recycled solution dye polyester yarn) 1150 dtex (solution dye polyester yarn) 3.5 METHOD OF DYEING Solution dye 3.6 FINISHING OPERATIONS wash, dry/heat-set,resin treatment,backcoating Or as

8、approved by Materials Engineering 4. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Specifications. 4.1 Purchase departments will ensure that the material defined in this specification and shipped to any one assembly plant will be produced by one supplier only. 5. SUMMARY OF REVISIONS