FORD W-EX7-2007 Remote Expert Assistance《远程专家协助》.pdf

《FORD W-EX7-2007 Remote Expert Assistance《远程专家协助》.pdf》由会员分享，可在线阅读，更多相关《FORD W-EX7-2007 Remote Expert Assistance《远程专家协助》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 Printed Copies are Uncontrolled Page 1 of 3 Standard Number w-EX7 Issue Date: 06-Feb-2007 Global Manufacturing Standards Remote Expert Assistance Rev: 1-1 1. PURPOSE AND SCOPE The aim of this Standard is to establish the minimum requirements for the: specification and use of remotely connected tech

2、nical assistance for manufacturing machine tools and equipment. 1.1. Applicability/Scope: This Standard applies to Ford Motor Companys manufacturing facilities, worldwide. 1.2. Exceptions None 1.3. Mandatory and Preferred Items Mandatory requirements are characterized by the use of the word “shall“.

3、 Departure from these requirements requires a written deviation from the Ford Global Manufacturing Standards - Electrical Technical Committee prior to system implementation. Preferred items are characterized by the use of the word “should“. 2. REFERENCE STANDARDS Whenever a specific Standard is refe

4、renced, it shall be the latest revision, unless otherwise specified. 2.1. Ford Standards and Specifications 2.1.1. Where applicable the REA system shall be in compliance with Ford Motor Company Information Technology Security and Control requirements. - http:/ 2.2. Industry Standards 2.2.1. None. Pr

5、inted Copies are Uncontrolled Page 2 of 3 Standard Number w-EX7 Issue Date: 06-Feb-2007 Global Manufacturing Standards Remote Expert Assistance Rev: 1-1 3. CONFORMANCE 3.1. Approval Process 3.1.1. Approval of Remote Expert Assistance (REA) solutions shall be made based on conformance to this Standar

6、d and agreement from the Ford Global Manufacturing Standards - Electrical Technical Committee. 3.1.2. All documentation shall be subject to the review of Ford Global Manufacturing Standards - Electrical Technical Committee. 4. DEFINITIONS 4.1. Application Control Review (ACR) A Ford IT process desig

7、ned to reduce the risk associated with information technology applications by ensuring that appropriate controls are implemented and functioning properly. 4.2. Application Code Software that is designed and written for a specific machine or equipment task. 4.3. End User - Person in the Ford Plant at

8、 the machine tool. 4.4. FMEA Failure Mode and Effect Analysis - A method that examines potential process failures, evaluates risk priorities, and helps determine remedial actions to avoid identified problems. 4.5. Local Controller - The device used to control the machine, e.g. PLC, CNC, Robot Contro

9、ller. 4.6. Monitor Mode - A Programming Software mode of operation that allows the Local Controller application to be monitored but prohibits any changes. 4.7. REA Application - The Remote Expert Assistance application software that allows the End User to request assistance and manages the authority

10、 to monitor the application from a remote location. 4.8. REA System Architecture The fundamental systems and procedures that together make up a Remote Expert Assistance application. 4.9. Remote Expert - Person at a remote location outside the Ford Plant. 4.10. Systems Control Review An annual review

11、 carried out to ensure the controls described in the ACR remain in place Printed Copies are Uncontrolled Page 3 of 3 Standard Number w-EX7 Issue Date: 06-Feb-2007 Global Manufacturing Standards Remote Expert Assistance Rev: 1-1 5. INSTRUCTIONS/REQUIREMENTS 5.1. Hardware and Software Configuration Re

12、quirements 5.1.1. An Application Control Review (ACR) for the proposed REA system architecture shall be initiated and closed prior to implementation approval. 5.1.2. An annual Systems Controls Review shall be carried out by the responsible Plant Systems department to ensure the controls described in

13、 the ACR are being followed. 5.1.3. An FMEA shall be provided and maintained for each REA system architecture. 5.1.4. The REA system shall prevent the activation or modification of the Application Code by a Remote Expert. 5.1.5. The REA system architecture shall prevent initiation of a service call

14、by a Remote Expert. 5.1.6. A specific REA page shall be provided on the machine or a local controller. Access to the page shall be restricted through the use of a user ID and password. 5.1.7. The Remote Expert shall require a user ID and password prior to being given access to the Application Code.

15、5.1.8. Protective measures shall be in place to maintain system integrity if an End User violates policy, and communicates their user ID and password to the Remote Expert. 5.1.9. After communication has been established and prior to the Remote Expert being able to view the Local Controller the End User shall grant permission by activating a confirmation on the machine or a local controller.