FORD FLTM BN 108-10-2001 CROCKMETER SCUFF TEST (Replaces FLTM BN 008-10 FLTM EU-BN 008-10)《耐磨损试验 摩擦测定仪法 替代FLTM BN 008-10 FLTM EU-BN 008-10［替代 FORD FLTM BN 008-10 FORD FLTM EU-BN 0.pdf

《FORD FLTM BN 108-10-2001 CROCKMETER SCUFF TEST (Replaces FLTM BN 008-10 FLTM EU-BN 008-10)《耐磨损试验 摩擦测定仪法 替代FLTM BN 008-10 FLTM EU-BN 008-10［替代 FORD FLTM BN 008-10 FORD FLTM EU-BN 0.pdf》由会员分享，可在线阅读，更多相关《FORD FLTM BN 108-10-2001 CROCKMETER SCUFF TEST (Replaces FLTM BN 008-10 FLTM EU-BN 008-10)《耐磨损试验 摩擦测定仪法 替代FLTM BN 008-10 FLTM EU-BN 008-10［替代 FORD FLTM BN 008-10 FORD FLTM EU-BN 0.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、FORD LABORATORY TEST METHOD BN 108-10 Date Action 2001 O924 Revised 1989 11 07 CROCKMETER SCUFF TEST Revisions Editorial - no technical change A. Cockman Application This method is used to determine the resistance to scuffing of the surface of trim materials. Apparatus Required Crockmeter - or equiv

2、alent equipment with a reciprocating stroke of variable length -50, 75, and 100 mm - together with an effective load of 900 g on the Scuffhead. Sources : Model CM-5 Atlas Electric Devices Co. 41 14 N. Ravenswood Ave. Chicago, Illinois U.S.A. Or Firma Walter Thoma 7888 Rheinfelden/Baden Wehrstrasse 6

3、 Germany Scuffhead The special Scuffhead required for this test (see Figure 1) is designed to replace the wooden cylindrical finger provided with the Crockmeter machine. Care must be taken to mount and firmly hold the Scuffhead blade perpendicular to the stroke of the machine. Conditioning and Test

4、Conditions All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +I- 2 “C and 50 +/- 5 % relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. Copynght02001, Ford Global Technologies, I

5、nc COPYRIGHT Ford Motor CompanyLicensed by Information Handling ServicesFORD LABORATORY TEST METHOD BN 108-10 Procedure 1. Prepare test specimens of 20 mm minimum width and where possible of 150 mm minimum length, so that the maximum stroke of the Crockmeter can be employed. Shorter lengths of speci

6、men may be used providing there is at least 10 mm of specimen in excess of the stroke length applied. 2. Position and secure the specimen on the support fixture so that the area to be evaluated is aligned with the stroke of the Scuffhead. 3. Adjust the Crockmeter stroke to the maximum length allowed

7、 bj the test specimen and scuff the specimen for the number of cycles required by the Engineering Materials Specification. Evaluation Remove specimen and assess according to the Engineering Materials Specification requirements. Do not include the last 6 mm at either end of the scuffed area in the ev

8、aluation. Note: When mounting foam backed specimens, depth of foam in excess of 7 mm must be removed unless otherwise indicated by the Engineering Materials Specification. The foam must be cut to provide as near as possible a horizontal level surface for the Scufhead to traverse. Chemicals, material

9、s, parts, and equipment referenced in this document must be used and handled properly. Each party is responsible for determining proper use and handling in its facilities. Page 2 of 3 Copynght02001, Ford Global Technologies, Inc COPYRIGHT Ford Motor CompanyLicensed by Information Handling ServicesFO

10、RD LABORATORY TEST METHOD BN 108-10 i 25 CROCKMETER SCUFF TEST 1 0.4 R ! 0.8 4 ( . . . . i” lj ,.a , . . . 32 3 mm BRAZED - ON CARBIDE TIP . i . SAE 1055 OR EPUIV WITH CARBIDE TIP CEMENTED TO DOWEL WOOD DOWEL Figure 1 Page 3 of 3 Copynght02001, Ford Global Technologies, Inc COPYRIGHT Ford Motor CompanyLicensed by Information Handling Services