FORD ESB-M9H118-A-1985 FABRIC NONWOVEN - RAYON POLYESTER - 50 G M2《50 G M2人造丝 聚酯无纺织物》.pdf

《FORD ESB-M9H118-A-1985 FABRIC NONWOVEN - RAYON POLYESTER - 50 G M2《50 G M2人造丝 聚酯无纺织物》.pdf》由会员分享，可在线阅读，更多相关《FORD ESB-M9H118-A-1985 FABRIC NONWOVEN - RAYON POLYESTER - 50 G M2《50 G M2人造丝 聚酯无纺织物》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONMaterial Name Spe cification NumberDate Release No. Release/Revision1985 08 29 C3P1-PR-524265 ReleasedWP 3948-a Page 1 of 2FABRIC, NON-WOVEN - RAYON/POLYESTER - 50 g/m 2 ESB-M9H118-A1. SCOPEThe material defined by this specification is a sized, non-woven,polyester/

2、rayon fabric with an acrylic resin.2. APPLICATIONThis specification was released originally for material used as adecorative and protective cover on fiberglass hood insulators for the1986 Tempo/Topaz.3. REQUIREMENTS3.1 CONDITIONINGAll test values indicated herein are based on material conditionedin

3、a controlled atmosphere of 23 +/- 2 C and 50 +/- 5%relative humidity for 24 h prior to testing and tested under thesame controlled conditions.3.2 ADDITIONAL REQUIREMENTSThis material must always be bonded 100% to another material toform a composite that will comply with flammability requirements.3.3

4、 THICKNESS 0.17 +/- 0.05 mm(SAE J315)3.4 WEIGHT(AATCC Test Methods 20 and 94)Fibrous Material 41 +/- 2 g/m 2(40% polyester/60% rayon)Acrylic Resin 9 +/- 2 g/m 23.5 BREAKING STRENGTH, min(ASTM D 1117 - Cut Strip Method 5.0 mm/s Jaw Speed)Machine Direction 20 NAcross Machine Direction 4 NENGINEERING M

5、ATERIAL SPECIFICATION ESB-M9H118-AWP 3948-b Page 2 of 23.6 COLOR As specified on engineering drawing3.7 FLAMMABILITY, max 101 mm/minTested in CompositeThis material must always be bonded 100% at all points to form acomposite (localized or spotty adhesion is unacceptable). Thecomposite shall not burn

6、 or transmit a flame across its surface, ata rate of more than 101 mm per min. To demonstrate compliance, thesample size and method of testing shall be in accordance with FLTMBN 24-2.3.8 INFRARED SPECTROPHOTOMETRYFord Motor Company, at its option, may conduct infrared analysis ofmaterial/parts suppl

7、ied to this specification. The spectraestablished for initial approval shall constitute the referencestandard and shall be kept on file at the designated materiallaboratory. All samples shall produce spectra that correspond tothe reference standard when tested under the same conditions asthose speci

8、fied on the master spectrum.3.9 SUPPLIERS RESPONSIBILITYAll materials supplied to this specification must be equivalent inall characteristics to the material upon which approval wasoriginally granted.Prior to making any changes in the properties, composition,construction, color, processing, or label

9、ing of the materialoriginally approved under this specification, whether or not suchchanges affect the materials ability to meet the specificationrequirements, the Supplier shall notify Purchasing, Toxicology, andthe affected Materials Engineering activity of the proposed changesand obtain the writt

10、en approval of the Materials Engineeringactivity. Test data, test samples, and a new code identificationare to be submitted with the request.Substance restrictions imposed by law, regulations, or Ford applyto the materials addressed by this document. The restrictions aredefined in Engineering Materi

11、al Specification WSS-M99P9999-A1,unless a different suffix (e.g., A2 or A3) is specified on theengineering document for the application.4. APPROVAL OF MATERIALSMaterials defined by this specification must have prior approval by theresponsible Materials Engineering activity. Suppliers desiring approv

12、alof their materials shall first obtain an expression of interest from theaffected Purchasing, Design, and Materials Engineering activity. Uponrequest, the Supplier shall submit to the affected Materials Engineeringactivity its own laboratory report to the specification (test results,not nominal values), the material designation and code number, and testspecimens for Ford evaluation. Upon approval, the material will be addedto the Engineering Material Approved Source List.