FORD ESB-M99P22-A2-2010 WEATHERING PERFORMANCE MOLDED-IN-COLOR UNPAINTED RIGID PLASTIC ELASTOMERIC MATERIALS INTERIOR TRIM TO BE USED WITH FORD WSS-M99P1111-A 《内饰用着色模塑的未涂漆硬质塑料 弹性.pdf

《FORD ESB-M99P22-A2-2010 WEATHERING PERFORMANCE MOLDED-IN-COLOR UNPAINTED RIGID PLASTIC ELASTOMERIC MATERIALS INTERIOR TRIM TO BE USED WITH FORD WSS-M99P1111-A 《内饰用着色模塑的未涂漆硬质塑料 弹性.pdf》由会员分享，可在线阅读，更多相关《FORD ESB-M99P22-A2-2010 WEATHERING PERFORMANCE MOLDED-IN-COLOR UNPAINTED RIGID PLASTIC ELASTOMERIC MATERIALS INTERIOR TRIM TO BE USED WITH FORD WSS-M99P1111-A 《内饰用着色模塑的未涂漆硬质塑料 弹性.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Release No. Release/Revision 2010 04 22 N-STATUS No replacement named L. Sinclair, NA 1993 01 04 NB00E10043064098 Revised & Updated KPM BCF L.A. Graham 1987 05 05 AR1-6000-221 Released L.A. Graham MP WP 3948-a Page 1 of 2 WE

2、ATHERING PERFORMANCE, MOLDED-IN-COLOR ESB-M99P22-A2 UNPAINTED RIGID PLASTIC/ELASTOMERIC MATERIALS, INTERIOR TRIM NOT TO BE USED FOR NEW DESIGN 1. SCOPE This specification defines the color stability performance of interior unpainted rigid plastic and/or elastomeric trim materials. 2. APPLICATION Thi

3、s specification was released originally for unpainted molded-in-color or transparent plastic/elastomeric materials that require UV resistance for interior applications. 3.1 STATISTICAL PROCESS Suppliers must conform to the requirements of Ford Quality System Standard Q-101. A mutually acceptable Con

4、trol Plan as described therein is required for material/source approval. Appropriate statistical tools must be used to analyze process/product data so that variation in the final product is continuously reduced. 3.2 WEATHERING RESISTANCE After exposure in accordance with 3.2.1, 3.2.2, and 3.2.3, the

5、 material shall show no color change in excess of specified AATCC rating (AATCC Gray Scale for Evaluating Change in Color, 10 step). In addition, there shall be no cracking, crazing or other deterioration. A slight loss of gloss or chalking will be allowed provided an acceptable appearance can be ac

6、hieved by washing with mild detergents and water (ratio 5:95 by volume) after the Florida exposure only. All initial approvals will be based on the preliminary Weatherometer Exposure, pending Florida Exposure results for final approval. 3.2.1 Xenon Arc Weatherometer (SAE J1885, specimen size: 150 x

7、100 mm minimum, 3.2 +/- 0.2 mm thick, molded in smooth polished mold) ENGINEERING MATERIAL SPECIFICATION ESB-M99P22-A2 WP 3948-b Page 2 of 2 Exposure, min AATCC Rating Polyolefins 1240 kJ/m2 4-5 (PP, PE, TEO) Polyamide 601 kJ/m2 4 3.2.2 Florida Exposure, 12 months 4 (5 deg south, under glass, specim

8、en size: 150 x 100 mm, minimum, 3.2 +/- 0.2 mm thick, unless otherwise specified) 3.2.3 Townsville Exposure, 12 months 3-4 (20 deg north, under glass) FOA applications only. 3.3 SUPPLIERS RESPONSIBILITY All materials supplied to this specification must be equivalent in all characteristics to the mat

9、erial upon which approval was originally granted. Prior to making any change in the properties, composition, construction, color, processing or labeling of the material originally approved under this specification, whether or not such changes affect the materials ability to meet the specification re

10、quirements, the Supplier shall notify Purchasing, Toxicology and the affected Materials Engineering activity of the proposed changes and obtain the written approval of the Materials Engineering activity. Test data, test samples and a new code identification are to be submitted with the request. Subs

11、tance restrictions imposed by law, regulations or Ford, apply to the materials addressed by this document. The restrictions are defined in Engineering Material Specification WSS-M99P9999-A1. 4. APPROVAL OF MATERIALS Materials defined by this specification must have prior approval by the responsible

12、Materials Engineering activity. Suppliers desiring approval of their materials shall first obtain an expression of interest from the affected Purchasing, Design and Materials Engineering activity. Upon request, the Supplier shall submit to the affected Materials Engineering activity a completed copy

13、 of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the requirements of this specification (test results, not nominal values), the material designation and code number, and test specimens for Ford evaluation. Fords engineering approval of a material will be based on its performance to this specification and on an assessment of suitability for intended processes and/or applications. Upon approval, the material will be added to the Engineering Material Approved Source List.