FORD ESB-M99J371-A2-2012 REMOVER TRANSIT COATING TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD ESB-M99J371-A1)《涂装的去除剂 与福特WSS-M99P1111-A 一起使用 在福特ESB-M99J371-A1中显示》.pdf

《FORD ESB-M99J371-A2-2012 REMOVER TRANSIT COATING TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD ESB-M99J371-A1)《涂装的去除剂 与福特WSS-M99P1111-A 一起使用 在福特ESB-M99J371-A1中显示》.pdf》由会员分享，可在线阅读，更多相关《FORD ESB-M99J371-A2-2012 REMOVER TRANSIT COATING TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD ESB-M99J371-A1)《涂装的去除剂 与福特WSS-M99P1111-A 一起使用 在福特ESB-M99J371-A1中显示》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev 02 2012 03 20 N Status No replacement named for A2 N. Benipal, NA 2006 03 21 Revised Inserted 3.0; Deleted 3.1, 3.7 and 4 1990 04 27 Released NB00E10063138000 Controlled document at www.MATS Copyright 2012, Ford Global Technologies, LLC P

2、age 1 of 2 TRANSIT COATING, ACRYLIC, WATER REDUCIBLE ESB-M99J371-A1 REMOVER, TRANSIT COATING NOT TO BE USED FOR NEW DESIGN ESB-M99J371-A2 1. SCOPE The materials defined by these specifications are a temporary transit coating and a remover with very low volatile organic compounds (VOC) content. The c

3、oating is applied over the topcoat enamel. 2. APPLICATION These specifications were released originally for materials to protect the enamel topcoat from environmental fallout paint damage during transit from the assembly plant to the Dealer and during storage on the Dealers lot. The remover is a sol

4、ubilizer to be used by the Dealer to remove the protective transit coating prior to delivery to the Customer. 3. REQUIREMENTS Material specification requirements are to be used for initial qualification of materials. 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part prod

5、ucers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.2 COMPOSITION 3.2.1 ESB-M99J371-A1, Transit Coating The transit coating is an aqueous solution of suitable resins that will provide adequate protection against paint damage. The remover is an aqueou

6、s solution of suitable wetting agents, amines and/or ammonia which will solubilize the transit coating. Specific composition data will be submitted by the Supplier on request. 3.3 FILM PROPERTIES 3.3.1 Film Thickness Requirements Coating thickness on 8 - 10 micrometer or as horizontal surfaces only

7、recommended by supplier ENGINEERING MATERIAL SPECIFICATION ESB-M99J371-A1/A2 Copyright 2012, Ford Global Technologies, LLC Page 2 of 2 3.4 RESISTANCE PROPERTIES 3.4.1 Dried Film: The film shall provide resistance to both organic and inorganic types of fallout contaminants. Examples of these types of

8、 contaminants are, but not limited to, acid rain, pollen, insect bodies and excrement, and industrial fallout contaminants. 3.4.2 Acid Spotting Test Procedure: . Apply 5 spots 8 - 10 mm in diameter of 3.5 and 4.0 pH H2SO4. . Let spots sit on painted surface for 30 minutes. . Wash off spots and dry.

9、. Examine spots for film swelling, lifting and/or discoloration. . Paint degradation in the spotted areas in excess of the control panel constitutes a failure. . Repeat test at both 37 +/- 2 C and 54 +/- 2 C. 3.5 WEATHERING PROPERTIES 3.5.1 Florida Exposure 6 months, 5 s (FLTM BI 160-01) After 6 mon

10、ths Florida exposure the coating shall not cause dirt pick up which would cause paint damage on removal. The coating after Florida exposure shall be removable without causing degradation to the paint film. 3.5.2 Accelerated Exposure 500 h QUV (SAE J2020) The completed test panel shall be subject to the same requirements as described above for Florida exposure panels. 3.6 COMPATIBILITY The coating and remover shall be compatible with all painted and unpainted materials used on the exterior of the vehicles.