BS ISO 8133-2014 Hydraulic fluid power Mounting dimensions for accessories for single rod cylinders 16 MPa (160 bar) compact series《液压流体动力 16 MPa (160 bar) 紧凑型系列单杆汽缸附件的安装尺.pdf
《BS ISO 8133-2014 Hydraulic fluid power Mounting dimensions for accessories for single rod cylinders 16 MPa (160 bar) compact series《液压流体动力 16 MPa (160 bar) 紧凑型系列单杆汽缸附件的安装尺.pdf》由会员分享,可在线阅读,更多相关《BS ISO 8133-2014 Hydraulic fluid power Mounting dimensions for accessories for single rod cylinders 16 MPa (160 bar) compact series《液压流体动力 16 MPa (160 bar) 紧凑型系列单杆汽缸附件的安装尺.pdf(28页珍藏版)》请在麦多课文档分享上搜索。
1、BSI Standards Publication BS ISO 8133:2014 Hydraulic fluid power Mounting dimensions for accessories for single rod cylinders, 16 MPa (160 bar) compact seriesBS ISO 8133:2014 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 8133:2014. It supersedes BS ISO 8133
2、:2006 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee MCE/18/-/3, Cylinders. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions o
3、f a contract. Users are responsible for its correct application. The British Standards Institution 2014. Published by BSI Standards Limited 2014 ISBN 978 0 580 81179 1 ICS 23.100.20 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published
4、under the authority of the Standards Policy and Strategy Committee on 30 November 2014. Amendments issued since publication Date Text affectedBS ISO 8133:2014 ISO 2014 Hydraulic fluid power Mounting dimensions for accessories for single rod cylinders, 16 MPa (160 bar) compact series Transmissions hy
5、drauliques Dimensions dinterchangeabilit des accessoires pour vrins, 16 MPa (160 bar) simple tige, srie compacte INTERNATIONAL STANDARD ISO 8133 Third edition 2014-11-15 Reference number ISO 8133:2014(E)BS ISO 8133:2014ISO 8133:2014(E)ii ISO 2014 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO
6、2014 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requ
7、ested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandBS ISO 8133:2014ISO 8133:2014(E)Contents
8、 Page Foreword iv Introduction v 1 Scope . 1 2 Normative references 1 3 Terms and definitions . 2 4 Mounting dimensions 2 5 Tolerances . 2 6 Application instructions . 2 6.1 Installation 2 6.2 Life spherical bearing 2 6.3 Lubrication . 3 7 Designation 3 8 Identification statement (reference to this
9、International Standard) 3 Bibliography .16 ISO 2014 All rights reserved iiiBS ISO 8133:2014ISO 8133:2014(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is n
10、ormally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part i
11、n the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular
12、 the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this d
13、ocument may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso
14、.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the W
15、TO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsible for this document is ISO/TC 131, Fluid power systems, Subcommittee SC 3, Cylinders. This third edition cancels and replaces the second edition (ISO 8133:2006),
16、 which has been technically revised.iv ISO 2014 All rights reservedBS ISO 8133:2014ISO 8133:2014(E) Introduction In hydraulic fluid systems, power is transmitted and controlled through a liquid under pressure within an enclosed circuit. One component of such systems is the fluid power cylinder. This
17、 is a device that converts power into linear mechanical force and motion. It consists of a movable element, i.e. a piston and piston rod, operating within a cylindrical bore. ISO 2014 All rights reserved vBS ISO 8133:2014BS ISO 8133:2014Hydraulic fluid power Mounting dimensions for accessories for s
18、ingle rod cylinders, 16 MPa (160 bar) compact series 1 Scope This International Standard specifies the mounting dimensions required for interchangeability of accessories for 16 MPa 160 bar ) compact cylinders conforming to ISO 6020-2. The accessories have been designed specifically for use with cyli
19、nders manufactured in accordance with ISO 6020-2, but this does not limit their application. Note 1 bar = 0,1 MPa = 10 5Pa; 1 MPa = 1 N/mm 2 . This International Standard covers the following accessories, identified in accordance with ISO 6099: AP6 rod eye spherical, female thread (see Figure 1 and
20、Table 1); AB5 clevis bracket, spherical eye, in angle (see Figure 2 and Table 2); AA6-L pivot pin, spherical bearing, locking plate (see Figure 3 and Table 3); AL6 locking plate for pivot pin (see Figure 4 and Table 4); AP2 rod clevis, female thread (see Figure 5 and Table 5); AP4 rod eye plain, fem
21、ale thread (see Figure 6 and Table 6); AB2 eye bracket (see Figure 7 and Table 7); AB4 clevis bracket, straight (see Figure 8 and Table 8); AA4-S pivot pin, plain (split pins) (see Figure 9 and Table 9); AA4-R pivot pin, plain (rings) (see Figure 10 and Table 10); AT4 trunnion bracket (see Figure 11
22、 and Table 11). These accessories are used on hydraulic cylinders for mechanically transmitting the cylinder force. The design of these accessories is based on the maximum forces resulting from the specified internal diameters of the cylinders and pressures according to ISO 3320 and ISO 3322. This I
23、nternational Standard only applies to the dimensional criteria of products manufactured in conformity with this International Standard; it does not apply to their functional characteristics. 2 Normative references The following documents, in whole or in part, are normatively referenced in this docum
24、ent and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 286-2, Geometrical product specifications (GPS) ISO code system for tolerances on linear
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BSISO81332014HYDRAULICFLUIDPOWERMOUNTINGDIMENSIONSFORACCESSORIESFORSINGLERODCYLINDERS16MPA160BARCOMPACTSERIES
链接地址:http://www.mydoc123.com/p-395776.html