ETSI TS 102 115-1-2002 Broadband Radio Access Networks (BRAN) HIPERACCESS Cell Based Convergence Layer Part 1 Common Part (V1 1 1)《宽带无线接入网(BRAN) HIPERACCESS 基于蜂窝的会聚层 第1部分 公共部分(版本1 .pdf

《ETSI TS 102 115-1-2002 Broadband Radio Access Networks (BRAN) HIPERACCESS Cell Based Convergence Layer Part 1 Common Part (V1 1 1)《宽带无线接入网(BRAN) HIPERACCESS 基于蜂窝的会聚层 第1部分 公共部分(版本1 .pdf》由会员分享，可在线阅读，更多相关《ETSI TS 102 115-1-2002 Broadband Radio Access Networks (BRAN) HIPERACCESS Cell Based Convergence Layer Part 1 Common Part (V1 1 1)《宽带无线接入网(BRAN) HIPERACCESS 基于蜂窝的会聚层 第1部分 公共部分(版本1 .pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、ETS I TS 1 02 1 1 5- 1 VI .I .I (2002-09) Technical Specificafion Broadband Radio Access Networks (BRAN); HIPERACCESS; Cell based Convergence Layer; Part 1: Common Part 2 ETSI TS 102 115-1 V1.l.l (2002-09) Reference DTSIBRAN-0034003-1 Keywords access, ATM, broadband, HIPERACCESS, radio ETSI 650 Rout

2、e des Lucioles F-O6921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 O0 Fax: +33 4 93 65 47 16 Siret No 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-prfecture de Grasse (06) No 7803/88 Important notice Individual copies of the present document can be downloade

3、d from: http:lwmv.etsi .arq The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference sh

4、all be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is avai

5、lable at ha p:/pa rta I. etsi I a rgltbistat uslstatus .as p If you find errors in the present document, send your comment to: Cori vriaht Notifica tion No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all med

6、ia. O European Telecommunications Standards Institute 2002. All rights reserved. DECTTM, PLUGTESTSTMand UMTSTMare Trade Marks of ETSI registered for the benefit of its Members. TIPHONTM and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a

7、 Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI 3 ETSI TS 102 115-1 V1.l.l (2002-09) Contents Intellectual Property Rights 4 Foreword . 4 1 2 3 3.1 3.2 4 5 5.1 5.2 5.2.1 5.3 5.3.1 5.3.2 5.3.3 Scope 5 References 5 Definitions and abbreviatio

8、ns . 5 . 5 . 5 Convergence Layer architecture . 6 Cell based Convergence Layer . 6 . 6 . 7 7 e Sublayer . . 8 Functional Model . 8 Primitives . 8 Procedures . . 9 . 5.3.3.1 General . 9 5.3.3.2 Procedures at the receiver . . 9 5.3.3.3 Procedures at the sender . 9 . 9 5.4 Functionality . . 9 5.5 5.5.1

9、 General . 9 5.5.2 Rules for connection mapping . 9 5.5.3 Coding ofthe CPCS-PDU 10 Interface to the DLC . Annex A (normative): Numbering and Coding Conventions . 11 Annex B (informative): ATM-cell format 12 Annex C (informative): Mapping Table Example . 13 Annex D (informative): SDL Diagrams 14 D.l

10、CPCS Sender 14 D.2 CPCS Receiver . 15 Annex E (informative): Bibliography . 16 History 17 ETSI 4 ETSI TS 102 115-1 V1.l.l (2002-09) Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essenti

11、al IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR O00 314: “Intellectual Property Rights (7PRs); Essential, orpotentially Essential, IPRs notlJied to ETSI in respect ofETSI standards“, which is available from the ETSI Secretariat. Latest updates are

12、 available on the ETSI Web server (5). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR O00 3 14 (or the updates on the ETSI Web server) which are, or may be,

13、 or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Project Broadband Radio Access Networks (BRAN). The present document defines the functionality required for the support of cell based services (ATM) over HIgh PErformance Radio Loc

14、al Area Network Type 2 (HIPERACCESS) 3. Separate ETSI documents provide details on the system overview, physical layer, data link control layer, other convergence sublayers and conformance testing requirements for HIPERACCESS. The Cell based Convergence Layer is split into several parts. Part 1, Com

15、mon Part, describes the functionality for mapping ATM cells into data units used at the Data Link Control (DLC) layer i. Further parts, each defining a Service Specific Convergence Sublayer (SSCS), describe the control plane functionality required to support a specific signalling protocol, e.g. ATMF

16、s M-UNI protocol (see annex E). It is envisioned that several, independent, service specific parts will be added as market requirements develop in the future. The present document is part 1 of a multi-part deliverable covering the HIPERACCESS; Cell based Convergence Layer, as identified below: Part

17、1: “Common part“; Part 2: “UNI Service Specific Convergence Sublayer (SSCS)“. Further parts may be added in the future. ETSI 5 ETSI TS 102 115-1 V1.l.l (2002-09) 1 Scope The present document describes the basic transport of ATM cell streams via HIPERACCESS. The mapping between ATM cells and HIPERACC

18、ESS DLC PDUs is specified. The present document does only address the functionality required to transfer ATM cells over the radio interface between a HIPERACCESS Access Point and Access Terminal. It does not address the requirements and technical characteristics for wired network interfaces at the A

19、ccess Point and at the Access Terminal. The Cell based Convergence Layer consists of a Common Part Convergence Sublayer, defined in the present document, and several Service Specific Convergence Sublayers (SSCS), which are defined in separate documents. The Service Specific Convergence Sublayers all

20、 use services provided by the Common Part Convergence Sublayer and the HIPERACCESS Data Link Control (DLC) layer i. The present document does not address the requirements and technical characteristics for conformance testing. These are covered by separate documents. 2 Re fe re nces The following doc

21、uments contain provisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication andor edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. For

22、a non-specific reference, the latest version applies. il ETSI TS 102 000: “Broadband Radio Access Networks (BRAN); HIPERACCESS; DLC protocol specification“. ITU-T Recommendation 1.361: “B-ISDN ATM layer specification“. ETSI TR 101 378: “Broadband Radio Access Networks (BRAN); Common ETSI -ATM Forum

23、reference model for Wireless ATM Access Systems (WACS)“. 21 31 3 3.1 Definitions and abbreviations De fi nit ions For the purposes of the present document, the following terms and definitions apply: Protocol Data Unit (PDU): data unit exchanged between entities at the same IS0 layer Service Data Uni

24、t (SDU): data unit exchanged between adjacent IS0 layers 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: AP Access Point AT Access Terminal ATM Asynchronous Transfer Mode CL Convergence Layer CLP Cell Loss Priority ETSI 6 ETSI TS 102 115-1 V1.l.l (2002-

25、09) CPCS DLC GFC HA HEC LAN LSB MSB “I OAM PDU PTI SDU sscs UNI M-UNI vc VCI VP VPI Common Part Convergence Sublayer Data Link Control Generic Flow Control HiperAccess Header Error Control Local Area Network Least Significant Bit Most Significant Bit Network Node Interface Operation And Management P

26、rotocol Data Unit Payload Type Identifier Service Data Unit Service Specific Convergence Sublayer User Network Interface User Network Interface + Mobility Extension Virtual Channel Virtual Channel Identifier Virtual Path Virtual Path Identifier 4 Convergence Layer architecture The Convergence Layer

27、(CL) resides on top of the Data Link Control (DLC) layer. The task of this Convergence Layer is to adapt the service requirements of ATM to the services offered by the HIPERACCESS DLC layer. c Higher Layers f .e f T T Convergence Layers Figure 4.1 : HIPERACCESS Convergence Layers 5 Cell based Conver

28、gence Layer 5.1 Gen eral The Cell based Convergence Layer provides the capability to transfer User Service Data Units (User SDUs), that correspond to an ATM cell, transparently between users of the Convergence Layer. The Cell based CL itself consists of two parts, a Common Part Convergence Sublayer

29、(CPCS) and a Service Specific Convergence Sublayer (SSCS). It is intended that several different Service Specific Convergence Sublayers will be specified within BRAN. An Access Point may support several SSCSs simultaneously. The CPCS describes the user plane functionality, i.e. how the information c

30、ontained in an ATM cell is mapped into a HIPERACCESS DLC transport unit (SDU) and vice versa. The Convergence Layer performs the adaptation between the User SDU and the DLC-SDU. ETSI 7 ETSI TS 102 115-1 V1.l.l (2002-09) The SSCS defines the mapping of Control Plane procedures for connection between

31、HIPERACCESS and the ATM specific control plane. Applications ILVI UNI signalling ATM I Figure 5.1: Protocol profile for Cell based Convergence Layer on ATM data transport (scope of HIPERACCESS specifications shaded in grey) Figure 5.1 shows a protocol profile for the Cell based Convergence Layer tha

32、t uses ATM for basic data transport. The application interfaces with the ATM user plane comprising of ATM AAL, ATM layer and the ATM control plane using the UNI signalling protocols. If needed, UNI signalling messages are encapsulated into AAL5 frames, which are segmented into ATM cells for further

33、transport. The Common Part Convergence Sublayer of the Cell based CL adapts the ATM cell format to the DLC-SDU of HA. The ATM control plane functionality, like connection control, is handled by the UNI signalling protocols. The UNI Service Specific Part of the Cell based CL translates UNI control pl

34、ane functions into the corresponding HA control plane functions. 5.2 Prim i tives (informative) The Common Part Convergence Sublayer exchanges service primitives with the Higher Layer and the DLC. NOTE: The primitives are defined only for the purpose of describing layer-to-layer and sublayer-to-subl

35、ayer interactions. These primitives are defined as an abstract list of parameters, and their concrete realization may vary between implementations. No formal testing of primitives is intended. The following primitive definitions have no normative significance. 5.2.1 Primitive types Interface between

36、 layers Four primitive types may be used between different layers: -req (request), for a higher layer to request service from a lower layer; -cnf (confirm), for the layer providing the service to confirm the activity has been completed; -ind (indication), for a layer providing service to notiSl the

37、next higher layer of any specific service related activity; -rsp (response), for a layer to acknowledge receipt of an indication primitive from the next lower layer. ETSI 8 ETSI TS 102 115-1 V1.l.l (2002-09) PARAMETER Message units (possible elements) Virtual Path Identifier (VPI) Virtual Channel Id

38、entifier (VCI) Cell Loss Priority (CLP) Payload Type Identifier (PTI) Payload data 5.3 Req Ind A A A A A A A A A A Common Part Convergence Sublayer 5.3.1 Functional Model The Higher Layer exchanges CL-SDUs (which correspond to ATM cells) with the Cell based Convergence Layer. Upon transmission the C

39、ell based Convergence Layer shall map the ATM payload and header information into a DLC-SDU, which shall be subsequently passed to the HIPERACCESS DLC layer for transmission to the peer-entity. Upon reception a DLC-SDU shall be passed to the Cell based Convergence Layer where a CL-SDU is reconstruct

40、ed and passed to the Higher Layer. Figure 5.2 shows the primitives between CL and Higher Level and primitives between CL and DLC layer that are used for further reference. Higher Layers CLData-ind T CLData-req Interface to SSCS Not specified CPCS - PDU to peer entity 4- - - - - - - - - DLC Layer Fig

41、ure 5.2: Cell based Convergence Layer User Plane model 5.3.2 Primitives The following primitives are used: CLData req, ind Virtual Path Identifier PPI): this parameter specifies an 8 bit Virtual Path Identifier in case of UNI or a 12 bit Virtual Path Identifier in case of “I. Virtual Channel Identif

42、ier PCI): this parameter specifies a 16 bit Virtual Channel Identifier as it is defined in 2 Cell Loss Priority (CLP): this 1 bit parameter specifies the cell loss priority as it is defined in 2. Payload Type Identifier (PTI): this parameter specifies a 3-bit payload type as it is defined in 2. Payl

43、oad data: the 48 octet user data. The above mentioned parameters are defined for an ATM cell, see also annex B. The ATM GFC field has only local meanings and it needs not to be transmitted over the air interface. ETSI 9 ETSI TS 102 115-1 V1.l.l (2002-09) 5.3.3 P roced u res 5.3.3.1 Gen era I The pro

44、cedures defied in the following clauses are symmetric with respect to the direction. The description is valid for both the AT and the AP. 5.3.3.2 Procedures at the receiver The receiver maintains the mapping between CID and the ATM connection identifiers (VPI, VCI) for each active DLC connection. Th

45、e ATM VCI field is always transparently carried by CPCS-PDU. The SSCS shall configure the mapping for each ATM connection. A CLData indication primitive shall be formed and passed to the Higher Layer once a CPCS-PDU is received from the peer-entity . A received CPCS-PDU with a non-configured mapping

46、 for the CID and the VCI field of the CPCS-PDU shall be discarded. The CL expects an in-sequence data transfer service from the DLC. The format of the CPCS-PDU is shown in figure 5.3. 5.3.3.3 Procedures at the sender The sender maintains the mapping between the ATM connection identifiers (VPI, VCI)

47、and CID for each active CID. The ATM VCI field is always transparently carried by CPCS-PDU. The SSCS shall configure the mapping for each ATM connection. The service user invokes the transmission service with a CLData request primitive. A CPCS-PDU is constructed as described in clause 5.5.3 and pass

48、ed within a DlcData request primitive to the DLC layer. A CPCS-PDU shall only be constructed and passed to the DLC layer as part of the CLData request primitive if the mapping for the VPI, VCI exists. 5.4 Interface to the DLC The DLC primitives are specified in the DLC specification i. The CL expect

49、s an in-sequence delivery data transfer service from the DLC. The format of the CPCS-PDU (which is equivalent to the DLC-SDU) is shown in figure 5.3. 5.5 Fu nct ion al i ty 5.5.1 General The CPCS functions are performed per CPCS-PDU. The function implemented by the CPCS comprises the transfer of User-data. This function is used for the conveyance of fixed length user data between users of the Convergence Layer. 5.5.2 Rules for connection mapping The following rules apply: 1) VCI, PTI and CLP fields from a CLData request primitive shall be copied into the correspondi