ETSI EN 302 065-3-2014 Electromagnetic compatibility and Radio spectrum Matters (ERM) Short Range Devices (SRD) using Ultra Wide Band technology (UWB) Harmonized EN covering the es.pdf

《ETSI EN 302 065-3-2014 Electromagnetic compatibility and Radio spectrum Matters (ERM) Short Range Devices (SRD) using Ultra Wide Band technology (UWB) Harmonized EN covering the es.pdf》由会员分享，可在线阅读，更多相关《ETSI EN 302 065-3-2014 Electromagnetic compatibility and Radio spectrum Matters (ERM) Short Range Devices (SRD) using Ultra Wide Band technology (UWB) Harmonized EN covering the es.pdf（37页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI EN 302 065-3 V1.1.1 (2014-04) Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD) using Ultra Wide Band technology (UWB); Harmonized EN covering the essential requirements of article 3.2 of the R Part 3: Requirements for UWB devices for road and rail vehic

2、les Harmonized European Standard ETSI ETSI EN 302 065-3 V1.1.1 (2014-04) 2Reference DEN/ERM-TGUWB-018 Keywords radio, regulation, SRD, testing, UWB ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C

3、 Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions

4、of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific

5、 network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in

6、the present document, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authoriz

7、ed by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2014. All rights reserved. DECTTM, PLUGTE

8、STSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association

9、. ETSI ETSI EN 302 065-3 V1.1.1 (2014-04) 3Contents Intellectual Property Rights 5g3Foreword . 5g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 7g33 Definitions, symbols and abbreviations . 8g33.1 Definitions 8g33.2 Symbols 9g33.3 Abbreviations . 9g34 Technical

10、requirements specification . 9g34.1 Operating bandwidth 9g34.1.1 Definition of operating bandwidth for test procedure . 9g34.1.2 Test procedure 9g34.1.3 Limit . 10g34.1.4 Measurement uncertainty 10g34.2 Mean power spectral density 10g34.2.1 Definition 10g34.2.2 Test procedure 10g34.2.3 Limit . 10g34

11、.2.4 Measurement uncertainty 11g34.3 Maximum value of peak power 11g34.3.1 Definition 11g34.3.2 Test procedure 11g34.3.3 Limit . 11g34.3.4 Measurement uncertainty 12g34.4 Receiver spurious emissions. 12g34.4.1 Definition 12g34.4.2 Test procedure 12g34.4.3 Limit . 12g34.4.4 Measurement uncertainty 12

12、g34.5 Exterior Limit . 13g34.5.1 Definition 13g34.5.2 Test Procedure 13g34.5.3 Limit . 13g34.5.4 Measurement uncertainty 14g34.6 Transmit Power Control (TPC) 14g34.6.1 Definition 14g34.6.2 Test procedure 14g34.6.3 Limit . 14g34.6.4 Measurement uncertainty 14g34.7 Detect And Avoid (DAA) 14g34.7.1 Def

13、inition 14g34.7.2 Test procedure 14g34.7.3 Limit . 14g34.7.4 Measurement Tolerance 14g34.8 Low Duty Cycle (LDC) 15g34.8.1 Definition 15g34.8.2 Test procedure 15g34.8.3 Limit . 15g34.9 Equivalent mitigation techniques . 15g34.9.1 Other mitigation techniques and mitigation factors 15g34.9.2 Power vs.

14、LDC Tradeoff Method . 16g3ETSI ETSI EN 302 065-3 V1.1.1 (2014-04) 45 Test Requirements 16g35.1 Product information 16g35.2 Requirements for the test modulation . 17g35.3 Test conditions, power supply and ambient temperatures 17g35.4 Choice of equipment for test suites 17g35.4.1 Multiple Operating ba

15、ndwidths and multiband equipment . 17g35.5 Testing of host connected equipment and plug-in radio devices 17g35.6 Interpretation of the measurement results 17g35.6.1 Measurement uncertainty is equal to or less than maximum acceptable uncertainty 18g35.6.2 Measurement uncertainty is greater than maxim

16、um acceptable uncertainty . 18g35.7 Emissions . 19g36 Test setups and procedures . 19g36.1 Introduction 19g36.2 Initial Measurement steps . 19g36.3 Radiated measurements 19g36.3.1 General 19g36.3.2 Test sites and general arrangements for measurements involving the use of radiated fields 19g36.3.3 Gu

17、idance on the use of a radiation test site . 19g36.3.3.1 Range length . 19g36.3.4 Coupling of signals . 20g36.3.5 Standard test methods . 20g36.3.5.1 Generic measurement method . 20g36.3.5.1.1 Calibrated setup . 20g36.3.5.1.2 Substitution method. 21g36.3.5.2 Spherical scan with automatic test antenn

18、a placement 22g36.3.5.2.1 Calibrated setup . 22g36.3.5.2.2 Substitution method. 23g36.3.5.3 Spherical scan with rotating and tilting the DUT 23g36.3.5.3.1 Calibrated setup. 24g36.3.5.3.2 Substitution method . 24g36.3.5.4 Spherical scan other methods 25g36.3.6 Standard calibration method . 25g36.4 Co

19、nducted measurements . 25g37 Test procedures for essential radio test suites 25g37.1 General . 25g37.2 Test Procedure 26g37.3 Method of measurements of the Ultra Wideband Emissions . 27g37.4 Mean power spectral density measurements 27g37.5 Peak power spectral density measurements 28g37.6 Operating b

20、andwidth 28g37.7 Receiver spurious emissions. 28g37.8 Transmitter Power Control . 28g37.9 Low Duty Cycle . 28g37.10 Detect and Avoid Mechanisms . 28g37.11 Exterior Limit . 28g3Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) 29g3Annex B (informative): Measureme

21、nt antenna, preamplifier, and cable specifications 31g3Annex C (informative): Surface mounted devices example mirror . 32g3Annex D (normative): Device mounted inside the tyre . 34g3Annex E (informative): Bibliography . 36g3History 37g3ETSI ETSI EN 302 065-3 V1.1.1 (2014-04) 5Intellectual Property Ri

22、ghts IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essentia

23、l, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by

24、 ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonized European Standard (EN) has been produced by ETSI Technical Com

25、mittee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been produced by ETSI in response to mandate M/407 issued from the European Commission under Directive 98/34/EC i.9 as amended by Directive 98/48/EC i.12. The title and reference to the present document a

26、re intended to be included in the publication in the Official Journal of the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC i.10. See article 5.1 of Directive 1999/5/EC i.10 for information on presumption of conformity and Harmonized Standards or parts t

27、hereof the references of which have been published in the Official Journal of the European Union. The requirements relevant to Directive 1999/5/EC i.10 are summarized in Annex A. Equipment covered by the present document operates in accordance with ECC/DEC(06)04 i.11 “The harmonised conditions for d

28、evices using Ultra-Wideband (UWB) technology in bands below 10,6 GHz“ in road and railway vehicles. The present document is part 3 of a multi-part deliverable covering Short Range Devices (SRD) using Ultra Wide Band technology (UWB) for communication purposes, as identified below: Part 1: “Requireme

29、nts for Generic UWB applications“; Part 2: “Requirements for UWB location tracking“; Part 3: “Requirements for UWB devices for road and rail vehicles“. National transposition dates Date of adoption of this EN: 8 April 2014 Date of latest announcement of this EN (doa): 31 July 2014 Date of latest pub

30、lication of new National Standard or endorsement of this EN (dop/e): 31 January 2015 Date of withdrawal of any conflicting National Standard (dow): 31 January 2016 ETSI ETSI EN 302 065-3 V1.1.1 (2014-04) 61 Scope The present document applies to transceivers, transmitters and receivers utilizing Ultr

31、a WideBand (UWB) technologies and used for short range applications in road and rail vehicles, which includes devices mounted inside or at the surface. The present document applies to impulse, modified impulse and RF carrier based UWB technologies in the main operating frequency ranges from 3,1 GHz

32、to 4,8 GHz or from 6 GHz to 9 GHz. Examples of applications for road and rail vehicles are: stand-alone radio equipment with or without its own control provisions; plug-in radio devices intended for use with, or within, a variety of host systems, e.g. personal computers, etc.; plug-in radio devices

33、intended for use within combined equipment, e.g. modems, access points, etc.; equipment for telemetry communication inside and outside of road and rail vehicles; equipment for the localization of devices inside and outside of road and rail vehicles (e.g. hand-held devices); equipment to investigate

34、materials (e.g. fuel). The present document does not apply to fixed road infrastructure installations. For fixed rail infrastructure tracking applications see TR 101 538 i.5 and TS 103 085 i.6. The present document applies to UWB equipment with an output connection used with a dedicated antenna or U

35、WB equipment with an integral antenna. The present document applies to UWB equipment conforming to ECC/DEC/(06)04 amended 9 December 2011 i.11 and CEPT Report 45 i.13. 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-speci

36、fic. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.

37、org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. 2.1 Normative references The following referenced documents are necessary for the application of the present document. 1 ETSI TS 102 883 (V1.1.1) (

38、08-2012): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD) using Ultra Wide Band (UWB); Measurement Techniques“. 2 ETSI TS 102 754 (V1.2.1) (11-2008): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Technical chara

39、cteristics of Detect-And-Avoid (DAA) mitigation techniques for SRD equipment using Ultra Wideband (UWB) technology“. 3 ETSI TR 100 028 (all parts) (V1.4.1) (12-2001): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment character

40、istics“. ETSI ETSI EN 302 065-3 V1.1.1 (2014-04) 72.2 Informative references The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 ETSI TR 102 070-2: “Electromagnetic compatibility and R

41、adio spectrum Matters (ERM); Guide to the application of harmonized standards to multi-radio and combined radio and non-radio equipment; Part 2: Effective use of the radio frequency spectrum“. i.2 ETSI TR 103 086: “Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (

42、SRD); Conformance test procedure for the exterior limit tests in EN 302065-3 UWB applications in the ground based vehicle environment“. i.3 ECC Report 120 (March 2008): “ECC Report on Technical requirements for UWB DAA (Detect and avoid) devices to ensure the protection of radiolocation in the bands

43、 3.1-3.4 GHz and 8.5-9 GHz and BWA terminals in the band 3.4-4.2 GHz“. i.4 Commission Decision 2007/131/EC of 21 February 2007 on allowing the use of the radio spectrum for equipment using ultra-wideband technology in a harmonised manner in the Community (notified under document number C(2007) 522).

44、 NOTE: This EC Decision is currently under revision based on CEPT Report 45 i.13 and amended ECC/DEC(06)04 i.11. The new EC/DEC revision is expected within 2014. i.5 ETSI TR 101 538: “Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); UWB location tracking dev

45、ices in the railroad environment“. i.6 ETSI TS 103 085: “Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD) using Ultra Wide Band (UWB) for Location and Tracking railroad applications; RF conformance testing“. i.7 CEPT/ERC Recommendation 74-01: “Unwanted emissi

46、ons in the spurious domain“. i.8 Void. i.9 Directive 1998/34/EC as amended by 1998/48/EC the European Parliament and of the Council of 22 June 1998 laying down a procedure for the provision of information in the field of technical standards and regulations. i.10 Directive 1999/5/EC of the European P

47、arliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (R the type of UWB technology implemented in the equipment (e.g. carrier-based, impulse, modified impulse, etc.); the type of modulation schemes av

48、ailable (e.g. OFDM modulation, pulsed modulation like PPM or Pulse Polarity Modulation or any other type of modulation, etc.); for all modulation schemes the modulation parameters need to be provided: for example modulation period, deviation or dwell times within a modulation period (FH systems), ra

49、te of modulation (Hz/s), number of carrier for OFDM, modulation bandwidth; the operating frequency range(s) of the equipment (see clause 7); ETSI ETSI EN 302 065-3 V1.1.1 (2014-04) 17 the type of the equipment (e.g. stand-alone equipment, plug-in radio device, combined equipment, etc.), (see also clause 5.5); the intended combination(s) of the radio equipment power settings and one or more antenna assemblies and their corresponding e.i.r.p. levels (see also clause 5.6); the nominal power supply voltage