EN ISO 17654-2011 en Resistance welding - Destructive tests of welds - Pressure test of resistance seam welds《电阻焊接 焊缝的破坏性试验 电阻缝焊的压力测试(ISO 17654-2011)》.pdf

《EN ISO 17654-2011 en Resistance welding - Destructive tests of welds - Pressure test of resistance seam welds《电阻焊接 焊缝的破坏性试验 电阻缝焊的压力测试(ISO 17654-2011)》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 17654-2011 en Resistance welding - Destructive tests of welds - Pressure test of resistance seam welds《电阻焊接 焊缝的破坏性试验 电阻缝焊的压力测试(ISO 17654-2011)》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 17654:2011Resistance welding Destructive tests of welds Pressure test of resistance seamwelds (ISO 17654:2011)BS EN ISO 17654:2011 BRITISH STANDARDNational forewordThis

2、 British Standard is the UK implementation of EN ISO 17654:2011. It supersedes BS EN ISO 17654:2003 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee WEE/29, Resistance welding.A list of organizations represented on this committee can be obtained on requ

3、est to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2011 ISBN 978 0 580 68855 3 ICS 25.160.40 Compliance with a British Standard cannot confer immunity from legal obligations.This British

4、 Standard was published under the authority of the Standards Policy and Strategy Committee on 30 September 2011.Amendments issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 17654 September 2011 ICS 25.160.40 Supersedes EN ISO 17654:2003Engli

5、sh Version Resistance welding - Destructive tests of welds - Pressure test of resistance seam welds (ISO 17654:2011) Soudage par rsistance - Essais destructifs des soudures -Essai de pression des soudures par rsistance la molette(ISO 17654:2011) Widerstandsschweien - Zerstrende Prfung von Schweiverb

6、indungen - Druckprfung an Widerstandsrollennahtschweiverbindungen (ISO 17654:2011) This European Standard was approved by CEN on 14 September 2011. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of

7、 a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German)

8、. A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, C

9、yprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION

10、 COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 17654:2011: EBS EN ISO 17654:2011EN ISO 17654:2011 (E) 3 F

11、oreword This document (EN ISO 17654:2011) has been prepared by Technical Committee ISO/TC 44 “Welding and allied processes” in collaboration with Technical Committee CEN/TC 121 “Welding” the secretariat of which is held by DIN This European Standard shall be given the status of a national standard,

12、either by publication of an identical text or by endorsement, at the latest by March 2012, and conflicting national standards shall be withdrawn at the latest by March 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/

13、or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 17654:2003. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austri

14、a, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. En

15、dorsement notice The text of ISO 17654:2011 has been approved by CEN as a EN ISO 17654:2011 without any modification. BS EN ISO 17654:2011ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing

16、 International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liais

17、on with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of tech

18、nical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn

19、 to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 17654 was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee SC 6, Resistance wel

20、ding and allied mechanical joining.This second edition cancels and replaces the first edition (ISO 17654:2003), which has been technically revised.Requests for official interpretations of any aspect of this International Standard should be directed to the Secretariat of ISO/TC 44/SC 6 via your natio

21、nal standards body. A complete listing of these bodies can be found at www.iso.org.ISO 17654:2011(E) ISO 2011 All rights reserved iiiBS EN ISO 17654:2011BS EN ISO 17654:2011INTERNATIONAL STANDARD ISO 17654:2011(E)Resistance welding Destructive tests of welds Pressure test of resistance seam welds1 S

22、copeThis International Standard specifies the pressure test method to be applied to resistance-seam-welded specimens of different types of materials with single sheet thicknesses ranging from 0,3 mm to 3,2 mm.The purpose of this pressure test is to determine the suitability of the material, welding

23、equipment, welding parameters and of other factors on a tank, a vessel or a container for liquids or gases, which are manufactured by resistance seam welding.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only th

24、e edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 14329, Resistance welding Destructive tests of welds Failure types and geometric measurements for resistance spot, seam and projection weldsISO 17677-1, Resistance we

25、lding Vocabulary Part 1: Spot, projection and seam welding3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 17677-1 and ISO 14329 apply.4 Purpose of testThe pressure test can be performed as a type test.5 Test specimens5.1 RequirementsThe following shal

26、l apply to the preparation of all specimens. Materials, thickness, heat treatment and condition of the sheets used for the test specimens shall be identical to those used for welding the actual component. For a given welding process, the welding equipment used to produce the test specimens shall hav

27、e a specification comparable to that used for welding the actual component.In special cases, e.g. transfer of welding parameters into production lines, the same parameters should be used. It has to be ensured that the electrodes that are used to weld the specimens shall be of the same material and g

28、eometry as the ones used for welding the actual component.5.2 DimensionsDimensions of resistance-seam-welded test specimens, of type A and type B, are given in Figure 1. ISO 2011 All rights reserved 1BS EN ISO 17654:2011Dimensions in millimetres(t2 t1) (t2 t1)a) Type A Specimen with four seams b) Ty

29、pe B Specimen with one seamKey1 leakproof weldR radius specified for the productt1thickness of top sheett2thickness of bottom sheetd edge distance = 2,5 b (smaller distances may be used for wire seam welding)b width of weld seamFigure 1 Dimensions of test specimens5.3 Number of test specimensAt leas

30、t three test specimens shall be tested.6 Test equipment and test procedureThe test shall be carried out with the specimen shown in Figure 1 assembled in a restraining fixture as shown in Figure 2. The purpose of the restraining fixture is to restrict expansion of the specimen within the expansion ra

31、nge, G, indicated in Figure 2.The test specimen shall be connected to a supply of compressed air or water at the specified pressure and in the case of compressed air immersed in a water bath. No leaks (in the form of bubbles escaping from any of the seam welds after a specified time) are permitted.I

32、SO 17654:2011(E)2 ISO 2011 All rights reservedBS EN ISO 17654:2011(t2 t1)Key1 nuts to adjust G G expansion range (t1+ t2+ 20 mm) (restricted expansion)2 water or compressed air supply connectiont1sheet thickness of top sheet3 leakproof weld t2sheet thickness of bottom sheet4 test specimenFigure 2 Re

33、straining fixtureIf the test pressure is not specified, the test specimen shall be checked for leakage either at a pressure sufficient to deform the sample by 20 mm, see Figure 2, or at 0,15 MPa, whichever is the lower pressure.If a test pressure greater than 0,15 MPa is specified, for safety reason

34、s, the test shall be conducted in air using internal water pressure. No leakage of water from any of the seam welds is permitted during the specified time.The time during which the test pressure is to be maintained shall be specified. This generally depends on the material, the weld process and the

35、product specification.7 Test reportThe test report shall include at least the following information:a) a reference to this International Standard (ISO 17654:2011);b) the test materials and sheet thicknesses;c) chemical composition and mechanical properties of the test materials;d) the geometry of th

36、e test specimens;e) welding method (seam welding);f) welding equipment and welding parameters;g) weld dimensions;h) test results, test pressure and time for which the pressure is maintained during the test, pressure fluid;i) any deviation(s) from this International Standard.ISO 17654:2011(E) ISO 201

37、1 All rights reserved 3This page deliberately left blankThis page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services. It presents the UK view on standards in Europe and at the inter

38、national level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of British Stan-dards should

39、 make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British Standard would inform the Secretary of the technical com-mittee

40、 responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax:

41、+44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001

42、Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeana

43、nd international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing M

44、embers are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to Brit

45、ish Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the international standardization bodies. Ex-cept as permitted under the Copyr

46、ight, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the freeuse, in the course of implementing the s

47、tandard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email: