EN ISO 15252-1-1999 en Plastics - Epoxy Powder Moulding Compounds (EP-PMCs) - Part 1 Designation System and Basis for Specifications《塑料 环氧树脂模塑化合物(EP-PMCs) 第1部分 命名体系及基本规范 ISO 15252-.pdf

《EN ISO 15252-1-1999 en Plastics - Epoxy Powder Moulding Compounds (EP-PMCs) - Part 1 Designation System and Basis for Specifications《塑料 环氧树脂模塑化合物(EP-PMCs) 第1部分 命名体系及基本规范 ISO 15252-.pdf》由会员分享，可在线阅读，更多相关《EN ISO 15252-1-1999 en Plastics - Epoxy Powder Moulding Compounds (EP-PMCs) - Part 1 Designation System and Basis for Specifications《塑料 环氧树脂模塑化合物(EP-PMCs) 第1部分 命名体系及基本规范 ISO 15252-.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、Plastics - Epoxy powder moulding compounds (EP-PMCS) - Part 1: Designation system and basis for specifications The European Standard EN IS0 15252-1: 1999 has the status of a British Standard o 093 m iS EN IS0 .5252-1:2000 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW STD-BSI

2、 BS EN IS0 15252-1-ENGL 2000 16246b9 OBSbBL T2T BS EN IS0 15252-1:2000 direction of the Sector Amd. No. Committee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 January 2000 O BSI 01-2000 National foreword Date Comments This Brit

3、ish Standard is the English language version of EN IS0 15252-1:1999. It is identical with IS0 15252-1:1999. The UK participation in its preparation was entrusted to Technical Committee PRU42, Fibre reinforced thermosetting piastics and prepregs, which has the responsibility to: - aid enquirers to un

4、dersand the text; - present to the responsible intemationavEuropean committee any enquiries on the interpretation, or proposais for change, and keep the UK interests informed; - monitor related international and European developments and promulgate them in the UK A list of organizations represented

5、on this committee can be obtained on request to its secretary. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards norndiy include an annex which lists normative references to intrnationai publications with their corresponding European publications. The British Standards w

6、hich implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled ?International standards Correspondence Index?, or by using the ?Find? faci!.ity of the BSI Standards Electronic Catalogue. A British Standard does not purport to includ

7、e ail the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN

8、IS0 title page, the EN IS0 foreword, the IS0 title page, pages ii and iii, a blank page, pages 1 to 6, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. ISBN O 580 35888 7 STD*BSI BS EN IS0 25252-2-ENGL 2000 .II Lb

9、24bb9 0826882 9bb EUROPEAN STANDARD EN IS0 152524 NORME EUROPENNE EUROPISCHE NORM November 1999 ICs 83.080.10 English version Plastics - Epoxy powder moulding compounds (EP-PMCs) - Part 1 : Designation system and basis for specifications (IS0 15252- 1 : 1 999) Plastiques - Poudres mouler base dpoxyd

10、es (EP- PMC) - Partie 1: Systme de dsignation et base de spciiication (IS0 15252-1:1999) This European Standard was approved by CEN on 13 October 1999. CEN members are bound to comply wih the CEWCENELEC internal Regulations which stipulate the conditions for giving this European Standard the status

11、of a national standard without any alteration. Up-to-date lists and bibliographicat references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A vers

12、ion in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, Fran

13、ce, Germany, Greece, Iceland, Ireland, Italy. Luxembourg, Netherlands, Norway, Portugal. Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMiTTEE FOR STANDARDIZATION EUROPISCHES KOMITEE FOR NORMUNG COMITE EUROPEEN DE NORMALISATION Central Secretariat: rue de Stassart, 36 B-1050 Brussels (9

14、1999 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN IC0 15252-1:1999 E STDOBSI BS EN IS0 15252-L-ENGL 2000 W lb24bb7 082b8B3 BT2 ai EN IS0 15252-1:1999 Foreword The text of the International Standard IS0 15252-1 :1999 has been pre

15、pared by Technical Cornmittee ISO/TC 61 Plastics in collaboration with Technical Committee CEN/TC 249 “Plastics”, the secretariat of which is held by IBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the lat

16、est by May 2000, and conflicting national standards shall be withdrawn at the latest by May 2000. According to the CENKENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark

17、, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. NOTE FROM CEWCS: The foreword is susceptible to be amended on reception of the German language version. The confirmed or amended foreword, and wh

18、en appropriate, the normative annex ZA for the references to international publications with their relevant European publications will be circulated with the German version. Endorsement notice The text of the International Standard IS0 15252-1 :1999 was approved by CEN as a European Standard without

19、 any modification. STD.BSI BS EN IS0 15252-1-ENGL 2000 Lb24bb 082b884 739 18 EN IS0 15252-1:1999 I NTE RN ATION AL STANDARD IS0 15252-1 First edition 1999-1 1-1 5 Plastics - Epoxy powder moulding compounds (EP-PMCs) - Part 1: Designation system and basis for specifications Plastiques - Poudres moule

20、r base dpoxydes (EP-PMC) - Partie 1: Systme de dsignation et base de spcification Reference number IS0 15252-1 11 999(E) - STDmBSI BS EN IS0 15252-I,-ENGL 2000 m 1624669 082L885 b75 EN IS0 15252-1:1999 Foreword IS0 (the International Organization for Standardization) is a worldwide federation of nat

21、ional standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Interna

22、tional organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the r

23、ules given in the ISOAEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 O/O of the member bodies casting a vote. Attention is drawn to the

24、possibility that some of the elements of this part of IS0 15252 may be the subject of patent rights. IS0 shall not be held responsible for identifying any or all such patent rights. International Standard IS0 15252-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 12, Thermo

25、setting materials. IS0 15252 consists of the following parts, under the general title Plastics - Epoxy powder moulding compounds (EP- PMCS): - Part 7: Designation system and basis for specifications - Part 2: Preparation of test specimens and determination of properties - Part 3: Requirements for se

26、lected moulding compounds Previous page is blank . 111 Plastics - Epoxy powder moulding compounds (EP-PMCs) - Part 1: Designation system and basis for specifications 1 Scope 1.1 compounds (EP-PMCs). This part of IS0 15252 establishes a data block system for the designation of epoxy powder moulding 1

27、.2 The various types of EP-PMC are differentiated from each other by a classification system based on information about the filler/reinforcement type and content, the intended method of processing, any special properties and those of the special properties used specifically for designation purposes

28、(designatory properties). 1.3 ground material. This part of IS0 15252 is applicable to all EP-PMCs ready for normal use in the form of powder, granules or 1.4 it is not intended to imply that materials having the same designation necessarily give the same performance. This part of IS0 15252 does not

29、 provide engineering data, Performance data or data on processing conditions which may be required to specify a material for a particular application and/or method of processing. If such additional properties are required, they shall be determined in accordance with the test methods specified in par

30、t 2 of this International Standard, if suitable. 1.5 indicated, this is also done using this data block system. Whenever general requirement data, as covered by part 3 of this International Standard, need to be 1.6 To ensure that code-letters and code-numbers remain unambiguous, and to avoid conflic

31、ts within the system, any new code-letters or code-numbers for use in data block 1, 2 or 3 shall be approved before use by the secretariats of ISOKC 61/SC 1. SC 12 and SC 13. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute

32、 provisions of this part of IS0 15252. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of IS0 15252 are encouraged to investigate the possibility of applying the most recent editions of the nor

33、mative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of IS0 and IEC maintain registers of currently valid International Standards. IS0 75-2:1993, Plastics - Determination of temperature of deflection under load - Pari 2:

34、Plastics and ebonite. IS0 179-1 :-l), Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test. IS0 472999, Plastics - Vocabulaty. 1) To be published. (Revision of IS0 179:1993) 1 STD-BSI BS EN IS0 55252-I-ENGL 2000 11111 Lb24bb9 082b887 448 m EN IS0 15252-1:1999 D

35、escription block IS0 1043-1:1997, Plastics - Symbols and abbreviated terms - Part 1: Basic polymers and their special characteristics. Identity block Individual-item block Data Data Data Data Data block block block block block 1 2 3 4 5 IS0 Standard IS0 1 043-2:-2), Plastics - Symbols and abbreviate

36、d terms - Part 2: Fillers and reinforcing materials. IS0 15252-2: 1 999, Plastics - Epoxy powder moulding compounds (EP-PMCs) - Part 2: Preparation of test specimens and determination of properties. IS0 15252-3:1999, Plastics - Epoxy powder moulding compounds (EP-PMCs) - Part 3: Requirements for sel

37、ected moulding compounds. 3 Terms and definitions For the purposes of this part of IS0 15252, the terms and definitions given in IS0 472 and IS0 15252-2 apply, plus the following: 3.1 powder moulding compound powder, granules or ground material capable of flowing freely through the feed systems of p

38、rocessing machines, as well as moulding compounds in the form of flakes which are normally not thought of as powders The abbreviation for powder moulding compound is PMC by analogy with bulk moulding compound (BMC) and sheet moulding compound (SMC). 3.2 the abbreviation for powder moulding compounds

39、 based on epoxy resins for both injection and compression moulding EP-PMC 4 Designation system 4.1 General The designation system defined in this part of IS0 15252 is based on the following standardized pattern: I Designation I The designation consists of an optional description block, reading “PMC“

40、, and an identity block comprising the International Standard number and an individual-item block. For unambiguous designation, the individual-item block is subdivided into five data blocks comprising the following information: 2) To be published. (Revision of IS0 1043-2:1988) 2 Data block 1 : Marki

41、ng block Item 1: Identification of the basic polymer by its symbol, in accordance with IS0 1043-1. Item 2: Nature of the designatory reinforcement materials or fillers, in accordance with IS0 1043-2. Item 3: Form of the designatory reinforcement materials or fillers, in accordance with IS0 1043-2. I

42、tem 4: Nominal content of the designatory reinforcement materials or fillers, in accordance with Table 1. Data block 2: Method of processing Method of processing for which the moulding compound is intended, designated in accordance with Table 2. Data block 3: Properties Item 1 : Special properties,

43、in accordance with Table 3. Item 2: Designatory property No. 1 - impact strength determined in accordance with IS0 179-1. Item 3: Designatory property No. 2 -temperature resistance determined in accordance with IS0 75-2. Data block 4: Further information, taken from an international, national or com

44、pany standard Data block 5 (optional): Additional requirements The first character of the individual-item block shall be a hyphen. The data blocks shall be separated from each other by commas. If a data block is not used, this shall be indicated by an “X“ (= not applicable), but only if another bloc

45、k follows. For labelling purposes, and provided no other blocks follow, the comma between blocks 1 and 2 can be ommitted. There is no need to fill in data blocks if they are not required. 4.2 Data block 1 Item 1: After the hyphen, epoxy powder moulding compounds shall be identified by the symbol EP,

46、 in accordance with IS0 1043-1. Mixtures and modifications shall be designated in accordance with IS0 1043-1:1997, subclauses 4 and 5. The following information shall be restricted to designatory fillers/reinforcements used in the material in question: Item 2: Nature of filler/reinforcement, in acco

47、rdance with Table 1. Item 3: Form of filler/reinforcement, in accordance with Table 1. Item 4: Nominal content (mass YO) of filler/reinforcement, in accordance with Table 1. Note, in particular, the following: - the same code-letters have different meanings when used for item 2 and item 3; - wheneve

48、r information needs to be indicated only for item 3, an “X“ ( = not applicable) is required for item 2. 3 STD-BSI BS EN IS0 L5252-L-ENGL 2000 I1624669 082b869 210 W EN IS0 16262-1:1999 G M Q 4.3 Data block2 General purpose T Transfer moulding Injection moulding X Not specified Compression moulding 2

49、 Others In this data block, information about the method of processing is given using the code-letters specified in Table 2. The code-letter used to indicate the intended method of processing in data block 2 shall be selected carefully. Certain brands of material can be processed in more than one way, e.g. either by compression moulding (Q) or by injection moulding (M). Such brands shall be designated “general purpose“ (G). The designation of special methods of processing shall be reserved for specially modified materials. Tab