EN ISO 13534-2000 en Petroleum and Natural Gas Industries - Drilling and Production Equipment - Inspection Maintenance Repair and Remanufacture of Hoisting Equipment《石油和天然气工业 钻井和生产.pdf

《EN ISO 13534-2000 en Petroleum and Natural Gas Industries - Drilling and Production Equipment - Inspection Maintenance Repair and Remanufacture of Hoisting Equipment《石油和天然气工业 钻井和生产.pdf》由会员分享，可在线阅读，更多相关《EN ISO 13534-2000 en Petroleum and Natural Gas Industries - Drilling and Production Equipment - Inspection Maintenance Repair and Remanufacture of Hoisting Equipment《石油和天然气工业 钻井和生产.pdf（21页珍藏版）》请在麦多课文档分享上搜索。

1、STD*BSI BS EN IS0 13534-ENGL 2OOL II Lb24bb9 0891945 710 BRITISH STANDARD I BS EN IS0 13534:2001 Petroleum and natural gas industries - Drilling and production equipment - Inspection, maintenance, repair and re-manufacture of hoisting equipment The European Standard EN IS0 13534:2 has the status of

2、a British Standard ICs 76.180.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMiTTED BY COPYRIGHT LAW National foreword direction of the Engineering Amd. No. Date Sedor Committee, was published under the authority of the Standards Committee and comes into effect on 16 February 2001 This British St

3、andard is the officiai English language version of EN IS0 135W2000. It is identical with Is0 13534:2000. The UK participation in its preparation was entrusted to Technical Committee pSW17, Petroleum and natural gas industries, which has the responsibility to: Comments - aid enquirers to understand t

4、he text; - present to the responsible internatiod European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; - monitor related intedonal and European developments and promulgate them in the UK, A ist of organizations represented on this commi

5、ttee can be obtained on request to its secretary. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normaily include an annex which lists normative references to international publications with their corresponding European publidons. The British Standards which implement

6、 these international or European publications may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index“, or by using the “Find“ facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include ali the neces

7、sary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN IS0 title page,

8、 the EN Is0 foreword page, the IS0 title page, pages ii to v, a blank page, pages 1 to 12, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. O BSI 022001 I I ISBN O 580 36914 5 I I STD-ES1 BS EN IS0 L3534-ENGL 2001

9、 lb24bb9 0893947 593 EUROPEAN STANDARD EN IS0 13534 NORME EUROPENNE EUROPISCHE NORM December 2000 ICs 07.018.10 English version Petroleum and natural gas industries - Drilling and production equipment - Inspection, maintenance, repair and remanufacture of hoisting equipment (IS0 13534:2000) Industri

10、es du ptrole et du gaz naturel - Equipement de forage et de production - Vrification, maintenance, rparation et fabrication partir de matriaux recycls du matriel de levage (IS0 13534:2000) This European Standard was approved by CEN on 1 December 2000. CEN members are bound to comply with the CENEENE

11、LEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN

12、 member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN memb

13、ers are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMTEE FOR STANDARDIZATION COMITE EUROPEEN DE NORMALISATI

14、ON EUROPISCHES KOMITEE FOR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels Q 2000 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN IS0 13534:2000 E Foreword The text of the International Standard IS0 13534:2000 has be

15、en prepared by Technical Committee ISOTTC 67 I Materials, equipment and offshore structures for petroleum and natural gas industries“ in collaboration with Technical Committee CEN/TC 12 “Materials, equipment and offshore structures for petroleum and natural gas industries“, the secretariat of which

16、is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2001, and conflicting national standards shall be withdrawn at the latest by June 2001. According to the CENKENELEC Internal

17、Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and

18、the United Kingdom. NOTE FROM CMC: The foreword is susceptible to be amended on reception of the German language version. The confirmed or amended foreword, and when appropriate, the normative annex ZA for the references to international publications with their relevant European publications will be

19、 circulated with the German version. Endorsement notice The text of the International Standard IS0 13534:2000 was approved by CEN as a European Standard without any modification. STDmBSI BS EN IS0 13534-ENGL i1001 Lb24bb7 0871747 3bb O EN IS0 13634:2000 INTERNATIONAL IS0 STANDARD 13534 First edition

20、 2000-12-01 Petroleum and natural gas industries - Drilling and production equipment - Inspection, maintenance, repair and remanufacture of hoisting equipment Industries du ptrole et du gaz naturel - quipement de forage et de production - Vrification, maintenance, rparation et fabrication 21 partir

21、de matriaux recycls du matriel de levage Reference number IS0 13534:2000(E) STD-BSI BS EN IS0 13534-ENGL 2001 1b24bb9 0891950 088 EN IS0 13634:2000 Contents Page Foreword . iv Introduction . v 1 2 3 3.1 3.2 4 4.1 4.2 5 5.1 5.2 5.3 6 6.1 6.2 6.3 7 7.1 7.2 8 8.1 8.2 8.3 9 9.1 9.2 9.3 scope 1 Normative

22、 reference 2 Terms, definitions and abbreviated terms 2 Terms and definitions . 2 Abbreviated terms . 3 General principles 3 Procedures . 3 Personnel qualification . 4 Inspection and maintenance 4 General 4 Maintenance . 5 Inspection . 5 Procedures . 9 Bearings 9 Replacement parts . 9 Remanufacture

23、. 9 Procedures . 9 Verification . 10 Load testing 10 General 10 Performance load test . 10 Proof load test 10 Documentation and records . 10 General 10 User/owner equipment file 10 Activity records 11 Repair 9 Bibliography 12 Previous page is blank . . 111 STD.BS1 BS EN IS0 13534-ENGL 2001 - 1624669

24、 0893951 TI4 EN IS0 13534:ZOOO Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body intere

25、sted in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical

26、Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication

27、 as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. IS0 shall not be held responsible for identifying any or all such

28、patent rights. international Standard IS0 13534 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures for petroleum and natural gas industries, Subcommittee SC 4, Drilling and production equipment. iV STD-BSI BS EN IS0 L3534-ENGL 2OOL Lb24669 0893952 950 EN IS0

29、13534:2000 Introduction This International Standard is based on API RP 8B, 6h edition, December 1997 l. Users of this International Standard should be aware that further or differing requirements may be needed for individual applications. This International Standard is not intended to inhibit the us

30、er from utilizing alternative equipment, methods or engineering solutions for individual applications. This may be particularly applicable where there is innovative or developing technology. Where an alternative is offered, the vendor should identify any variations from this International Standard a

31、nd provide details. V STDIBSI BS EN IS0 L3534-ENGL 2001 M Lb24663 0831953 697 M EN IS0 13634:2000 Petroleum and natural gas industries - Drilling and production equipment - Inspection, maintenance, repair and remanufacture of hoisting equipment 1 Scope This International Standard gives guidelines an

32、d establishes requirements for inspection, maintenance, repair and remanufacture of items of hoisting equipment used in drilling and production operations, in order to maintain the serviceability of this equipment. Items of drilling and production hoisting equipment covered by this International Sta

33、ndard are: crown-block sheaves and bearings; travelling blocks and hook blocks: block-to-hook adapters; connectors and link adapters; drilling hooks; tubing hooks and sucker-rod hooks; e levator I inks ; casing elevators, tubing elevators, drill-pipe elevators and drill-collar elevators; sucker-rod

34、elevators; rotary swivel-bail adapters; rotary swivels; power swivels; power subs; spiders, if capable of being used as elevators: dead-line tie-down/wireline anchors; drill-string motion compensators; kelly spinners, if capable of being used as hoisting equipment; riser-running tool components, if

35、capable of being used as hoisting equipment; wellhead-running tool components, if capable of being used as hoisting equipment; safety clamps, capable of being used as hoisting equipment. 1 2 Normative reference The following normative document contains provisions which, through reference in this tex

36、t, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most rec

37、ent edition of the normative document indicated below. For undated references, the latest edition of the normative document referred to applies. Members of IS0 and IEC maintain registers of currently valid International Standards. IS0 97 12, Non-destructive testing - Qualification and certification

38、of personnel. 3 Terms, definitions and abbreviated terms For the purposes of this International Standard, the following terms, definitions and abbreviated terms apply. 3.1 Terms and definitions 3.1.1 critical area highly stressed region of a primary-load-carrying component as defined by the manufact

39、urer 3.1.2 expendable parts parts normally used up or consumed in service, EXAMPLES fasteners. Seals, gaskets, filters, packing, V-belts, covers, guards, breathers, drains and misceilaneous hardware and 3.1.3 inspection comparison of equipment conformity to predetermined standards, followed by a det

40、ermination of action required 3.1.4 load test test wherein a load is applied under controlled and monitored conditions to verify the serviceability of equipment 3.1.5 maintenance actions including inspection, adjustments, cleaning, lubrication, testing, and replacement of expendable parts, as necess

41、ary to maintain the serviceability of the equipment 3.1.6 manufacturer individual or company that makes or processes equipment or material covered by this International Standard 3.1.7 owner individual, legal entity or organization holding legal title to the equipment 3.1.8 primary load axial load to

42、 which the equipment is subjected in operation 3.1.9 primary-load-carrying component component of the equipment through which the primary load is carried STD.BSI BS EN IS0 13534-ENGL 2001 W 1624669 0893955 bbT EN IS0 13534:2000 3.1.1 O remanufacture action performed on equipment that involves a spec

43、ial process or re-machining 3.1.1 1 repair action performed on equipment that involves replacement of parts, other than expendable parts, but excludes remanufacture 3.1.12 serviceability condition of a piece of equipment at any point in time that affects the ability of the equipment to perform its f

44、unction(s) as intended 3.1 -1 3 special process operation that can change or affect the mechanical properties, including toughness, of the materials used in equipment 3.1.1 4 testing action carried out on a piece of equipment to ensure that it can perform a required function 3.1.1 5 user individual

45、or company that uses equipment or material, or implements standards 3.2 Abbreviated terms MT magnetic particle testing NDT non-destructive testing PSL product specification level PT liquid penetrant testing RT radiographic testing UT ultrasonic testing 4 General principles 4.1 Procedures 4.1.1 Gener

46、al Users/owners of hoisting equipment shall establish written procedures for inspection, maintenance, repair and remanufacture of each item of equipment. 4.1.2 Procedure development 4.1.2.1 User/owner and manufacturer joint procedure development The user/owner and manufacturer should jointly develop

47、 and update inspection, maintenance, repair and remanufacture procedures consistent with equipment application, loading, work environment, usage, and operational conditions. 3 STD.BS1 BS EN IS0 13534-ENGL 2001 m Lb24bb9 O919Cb 5Tb E EN IS0 13534:2000 These factors may change as a result of new techn

48、ology, product improvements or fundamental changes in service conditions. 4.1.2.2 User/owner procedure development If the manufacturer of the equipment no longer exists or is unable for any reason to provide suitable recommendations, the usedowner shall develop inspection, maintenance, repair and re

49、manufacture procedures consistent with widely-accepted industry practices. 4.1.2.3 Parts and tooling NDT, maintenance, and dismantling equipment shall be properly selected and adapted to the parts to be inspected and maintained. 4.2 Personnel qualification 4.2.1 NDT personnel qualification levels 4.2.1.1 Qualification Inspectors shall be aware of the type of equipment to be evaluated and the NDT methods to apply. The users/owners shall verify that the NDT inspector has the following information: - assembly drawings and drawings identifying cri