EN ISO 10675-2-2013 en Non-destructive testing of welds - Acceptance levels for radiographic testing - Part 2 Aluminium and its alloys《焊缝无损检测 射线检验的认可等级 第2部分 铝和铝合金》.pdf

《EN ISO 10675-2-2013 en Non-destructive testing of welds - Acceptance levels for radiographic testing - Part 2 Aluminium and its alloys《焊缝无损检测 射线检验的认可等级 第2部分 铝和铝合金》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 10675-2-2013 en Non-destructive testing of welds - Acceptance levels for radiographic testing - Part 2 Aluminium and its alloys《焊缝无损检测 射线检验的认可等级 第2部分 铝和铝合金》.pdf（20页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN ISO 10675-2:2013Non-destructive testing ofwelds Acceptance levels forradiographic testingPart 2: Aluminium and its alloysBS EN ISO 10675-2:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO10675-2:2013. It is identical to ISO

2、 10675-2:2010. It supersedes BS EN12517-2:2008 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee WEE/46, Non-destructive testing.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not pur

3、port to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 81137 1ICS 25.160.40Compliance with a British Standard cannot confer immunity fromlegal obligation

4、s.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 November 2013.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 10675-2 August 2013 ICS 25.160.40 Supersedes EN 12517-2:2008Englis

5、h Version Non-destructive testing of welds - Acceptance levels for radiographic testing - Part 2: Aluminium and its alloys (ISO 10675-2:2010) Essais non destructifs des assemblages souds - Niveaux dacceptation pour valuation par radiographie - Partie 2: Aluminium et ses alliages (ISO 10675-2:2010) Z

6、erstrungsfreie Prfung von Schweiverbindungen - Zulssigkeitsgrenzen fr die Durchstrahlungsprfung - Teil 2: Aluminium und seine Legierungen (ISO 10675-2:2010) This European Standard was approved by CEN on 8 August 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which st

7、ipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This Europea

8、n Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are t

9、he national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Roman

10、ia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means re

11、served worldwide for CEN national Members. Ref. No. EN ISO 10675-2:2013: EBS EN ISO 10675-2:2013EN ISO 10675-2:2013 (E) 3 Foreword The text of ISO 10675-2:2010 has been prepared by Technical Committee ISO/TC 44 “Welding and allied processes” of the International Organization for Standardization (ISO

12、) and has been taken over as EN ISO 10675-2:2013 by Technical Committee CEN/TC 121 “Welding” the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2014,

13、 and conflicting national standards shall be withdrawn at the latest by February 2014. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights.

14、 This document supersedes EN 12517-2:2008. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former

15、Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 10675-2:2

16、010 has been approved by CEN as EN ISO 10675-2:2013 without any modification. BS EN ISO 10675-2:2013ISO 10675-2:2010(E) ISO 2010 All rights reserved iiiContents Page Foreword.iv 1 Scope 1 2 Normative references 1 3 Radiographic technique1 4 General2 5 Acceptance levels2 Annex A (informative) Guide t

17、o the limitations of radiographic testing).5 A.1 Volumetric imperfections in butt welds.5 A.2 Cracks in butt welds5 A.3 Planar imperfections in butt welds 5 Annex B (informative) Examples for determination of percentage (%) of imperfections 6 Annex C (informative) Sum of acceptable areas8 Bibliograp

18、hy 10 BS EN ISO 10675-2:2013ISO 10675-2:2010(E) iv ISO 2010 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through I

19、SO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates

20、closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards.

21、Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this d

22、ocument may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10675-2 was prepared by the European Committee for Standardization (as EN 12517-2:2008) and was adopted, under a special “fast-track procedure”, by Technical Committee IS

23、O/TC 44, Welding and allied processes, Subcommittee SC 5, Testing and inspection of welds, in parallel with its approval by the ISO member bodies. Request for official interpretations of any aspect of this part of ISO 10675 should be directed to the Secretariat of ISO/TC 44/SC 5 via your national st

24、andards body. A complete listing of these bodies can be found at www.iso.org. BS EN ISO 10675-2:2013INTERNATIONAL STANDARD ISO 10675-2:2010(E) ISO 2010 All rights reserved 1Non-destructive testing of welds Acceptance levels for radiographic testing Part 2: Aluminium and its alloys 1 Scope This part

25、of ISO 10675 specifies acceptance levels for indications from imperfections in aluminium butt welds detected by radiographic testing. If agreed, the acceptance levels may be applied to other types of welds or materials. The acceptance levels may be related to welding standards, application standards

26、, specifications or codes. This part of ISO 10675 assumes that the radiographic testing has been carried out in accordance with ISO 17636. When assessing whether a weld meets the requirements specified for a weld quality level, the sizes of imperfections permitted by standards are compared with the

27、dimensions of indications revealed by a radiograph made of the weld. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced do

28、cument (including any amendments) applies. ISO 17636, Non-destructive examination of welds Radiographic examination of welded joints ISO 10042, Welding Arc-welded joints in aluminium and its alloys Quality levels for imperfections ISO 6520-1, Welding and allied processes Classification of geometric

29、imperfections in metallic materials Part 1: Fusion welding 3 Radiographic technique Depending on the weld quality level, radiographic technique A or B in accordance with ISO 17636 shall be used as shown in Table 1. Table 1 Radiographic testing Quality levels in accordance with ISO 10042 Testing tech

30、niques and classes in accordance with ISO 17636 Acceptance levels in accordance with this part of ISO 10675 B B 1 C B a2 D A 3 aHowever, the minimum number of exposure for circumferential weld testing may correspond to the requirements of class A of ISO 17636. BS EN ISO 10675-2:2013ISO 10675-2:2010(

31、E) 2 ISO 2010 All rights reserved4 General Welded joints should be visually tested in accordance with ISO 17637 and evaluated before radiographic testing. The acceptance levels in this part of ISO 10675 are basically valid for evaluation of imperfections which cannot be detected and evaluated by vis

32、ual testing (Table 2). Surface imperfections (Table 3; such as undercut and excessive penetration, surface damage, weld spatter, etc.) which due to object geometry cannot be evaluated, but where the interpreter suspects the ISO 10042 quality levels are not fulfilled, shall be subject to more specifi

33、c testing. When quantification of undercut and/or excessive penetration by radiographic testing is required, specific procedures using test exposures may be applied in order to establish a basis for approximate quantification in accordance with the requirements of ISO 10042. This shall be specified.

34、 5 Acceptance levels The acceptance levels for indications are shown in Tables 2 and 3. The types of imperfections are selected from ISO 10042 and defined in ISO 6520-1. The symbols used in Tables 2 and 3 are the following: A sum of projected areas of indications related to L wpin %; b width of exce

35、ss penetration of weld, in millimetres; d diameter of pore, in millimetres; dAdiameter of area surrounding a cluster, in millimetres; h width of indication, the width or height of surface or cross surface imperfection, in millimetres; l length of indication, in millimetres; L any 100 mm testing leng

36、th, in millimetres; s nominal butt weld thickness, in millimetres; t material thickness, in millimetres; wpwidth of the weld in millimetres; l summary length of imperfections within L. Any two adjacent imperfections separated by a distance smaller than the major dimension of the smaller imperfection

37、 shall be considered as a single imperfection. Indications shall not be divided into different ranges L. BS EN ISO 10675-2:2013ISO 10675-2:2010(E) ISO 2010 All rights reserved 3Table 2 Acceptance levels for indications in butt welds No Type of internal imperfections in accordance with ISO 6520-1 Acc

38、eptance level 3 aAcceptance level 2 aAcceptance level 1 1 Cracks (100) Not permitted Not permitted Not permitted 2a Gas pores (2011) d 0,4s, max. 6 mm d 0,3s, max. 5 mm d 0,2s, max. 4 mm 2b Porosity (2012) material thickness 0,5 mm to 3 mm A 6 % L = 100 mm A 2 % L = 100 mm A 1 % L = 100 mm 2c Porosi

39、ty (2012) material thickness 3 mm to 12 mm A 10 % L = 100 mm A 4 % L = 100 mm A 2 % L = 100 mm 2d Porosity (2012) material thickness 12 mm to 30 mm A 15 % L = 100 mm A 6 % L = 100 mm A 3 % L = 100 mm 2e Porosity (2012) material thickness 30 mm A 20 % L = 100 mm A 8 % L = 100 mm A 4 % L = 100 mm 3 bC

40、lustered (localized) porosity (2013) dA 25 mm or dA,max wpdA 20 mm or dA,max wpdA 15 mm or dA,max wp/2 4 cLinear porosity (2014) l 25 mm L = 100 mm Not permitted Not permitted 5 dElongated cavities (2015) and wormholes (2016) l 0,4s, max. 6 mm l dA2Figure C.2 Clustered porosity, D = dA2The sum of th

41、e different pore areas (A1+A2.) related to the evaluation area L wp(Figure C.1). If D is less than dA1or dA2, whatever is smaller, an envelope surrounding the porosity area A1+A2shall be considered as one area of imperfection (Figure C.2). Figure C.3 Linear porosity, D d2 BS EN ISO 10675-2:2013ISO 1

42、0675-2:2010(E) ISO 2010 All rights reserved 9Figure C.4 Linear porosity, D = d2The sum of the different pore areas +.442221 ddrelated to the evaluation area L wp(Figure C.3). If D is smaller than the smaller diameter of one of the neighbouring pores, the full connected area of the two pores is to be

43、 taken into the sum of imperfections (Figure C.4). Figure C.5 Elongated cavities and wormholes, D l3Figure C.6 Elongated cavities and wormholes, D = l3 The sum of the length of indications l shall be determined for each testing length L(Figure C.5). If D is smaller than the shorter length of one of

44、the neighbouring imperfections, the full connection of the two imperfections is to be taken into the sum of imperfections (Figure C.6). BS EN ISO 10675-2:2013ISO 10675-2:2010(E) 10 ISO 2010 All rights reservedBibliography 1 ISO 17635, Non-destructive testing of welds General rules for metallic mater

45、ials 2 ISO 17637, Non-destructive testing of welds Visual testing of fusion-welded joints BS EN ISO 10675-2:2013This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information

46、 and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, co

47、nsumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sec

48、tors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standard

49、sYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to mak