EN ISO 10664-2014 en Hexalobular internal driving feature for bolts and screws《螺栓和螺钉用内板拧的六角花形(ISO 10664 2014)》.pdf

《EN ISO 10664-2014 en Hexalobular internal driving feature for bolts and screws《螺栓和螺钉用内板拧的六角花形(ISO 10664 2014)》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 10664-2014 en Hexalobular internal driving feature for bolts and screws《螺栓和螺钉用内板拧的六角花形(ISO 10664 2014)》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationBS EN ISO 10664:2014Hexalobular internal drivingfeature for bolts and screwsBS EN ISO 10664:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO10664:2014. It supersedes BS EN ISO 10664:2005 which is withdrawn.The UK participation in

2、 its preparation was entrusted to TechnicalCommittee FME/9, Fasteners.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplicat

3、ion. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 85833 8ICS 21.060.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee

4、on 31 October 2014.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 10664 October 2014 ICS 21.060.10 Supersedes EN ISO 10664:2005English Version Hexalobular internal driving feature for bolts and screws (ISO 10664:2014) Empreinte six lobes

5、 internes pour vis (ISO 10664:2014) Innensechsrund fr Schrauben (ISO 10664:2014) This European Standard was approved by CEN on 13 September 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a

6、 national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German).

7、A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyp

8、rus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Ki

9、ngdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 1

10、0664:2014 EBS EN ISO 10664:2014EN ISO 10664:2014 (E) 3 Foreword This document (EN ISO 10664:2014) has been prepared by Technical Committee ISO/TC 2 “Fasteners“ in collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN. This European Standard shall be gi

11、ven the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2015, and conflicting national standards shall be withdrawn at the latest by April 2015. Attention is drawn to the possibility that some of the elements of this document may be

12、 the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 10664:2005. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to i

13、mplement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Roma

14、nia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 10664:2014 has been approved by CEN as EN ISO 10664:2014 without any modification. BS EN ISO 10664:2014ISO 10664:2014(E) ISO 2014 All rights reserved iiiContents PageForeword iv1 Sc

15、ope . 12 Basic dimensions 13 Gauging . 23.1 Principle 23.2 GO gauge . 33.3 NO GO gauge 54 Designation 7Annex A (informative) Representation of hexalobular internal driving feature contour . 8BS EN ISO 10664:2014ISO 10664:2014(E)ForewordISO (the International Organization for Standardization) is a wo

16、rldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented o

17、n that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this

18、document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Dire

19、ctives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the devel

20、opment of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO

21、specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 2, Fasteners, S

22、ubcommittee SC 11, Fasteners with metric external thread.This third edition cancels and replaces the second edition (ISO 10664:2005), which has been technically revised with the following changes: several sizes of the driving feature have been added with respective values in Tables 1 to 5.iv ISO 201

23、4 All rights reservedBS EN ISO 10664:2014INTERNATIONAL STANDARD ISO 10664:2014(E)Hexalobular internal driving feature for bolts and screws1 ScopeThis International Standard specifies the shape and basic dimensions of the hexalobular internal driving feature for bolts and screws, including the gaugin

24、g method.The curvature of the contour of the hexalobular internal driving feature is defined by the gauges specified in Tables 3, 4, and 5. Additional information which can be used when drawing the contour is given in Annex A.The intent of this International Standard is to provide the details necess

25、ary for inspection of the hexalobular driving feature. It is not suitable for, nor intended to be used as, a manufacturing standard.2 Basic dimensionsSee Figure 1 and Table 1.Counterbore: c 0,13 mm up to socket no. 15c 0,25 mm over socket no. 15Penetration depth, t: see relevant product standard.aSe

26、e Table 2.NOTE The contour of the bottom of the socket beyond the gauge is at the option of the manufacturer.Figure 1 Basic dimensions ISO 2014 All rights reserved 1BS EN ISO 10664:2014ISO 10664:2014(E)Table 1 Basic dimensionsDimensions in millimetresHexalobular socket no.Nominal dimensionsaA B1 0,9

27、 0,62 1,0 0,73 1,2 0,854 1,35 1,05 1,5 1,16 1,75 1,277 2,1 1,58 2,4 1,759 2,6 1,910 2,8 2,0515 3,35 2,420 3,95 2,8525 4,5 3,2527 5,1 3,6830 5,6 4,0540 6,75 4,8545 7,93 5,6450 8,95 6,4555 11,35 8,0560 13,45 9,670 15,7 11,280 17,75 12,890 20,2 14,4100 22,4 16aThe curvature of the contour of the hexalo

28、bular internal driving feature is defined by the gauges specified in Tables 3, 4, and 5.3 Gauging3.1 PrincipleThe hexalobular internal driving feature shall allow the GO gauge (see 3.2) to enter freely to the penetration depth, t, as specified in the relevant product standards.The NO GO gauges (see

29、3.3.1 and 3.3.2) shall not enter the hexalobular internal driving feature to a depth greater than the fallaway allowance specified in Table 2.2 ISO 2014 All rights reservedBS EN ISO 10664:2014ISO 10664:2014(E)Table 2 Fallaway allowanceDimensions in millimetresSocket no. 1 2 3 4 5 6 7 8 9 10 15 20Fal

30、laway allowance f0,064 0,070 0,114 0,13 0,22 0,35 0,41 0,48 0,51 0,56 0,67 0,79Socket no. 25 27 30 40 45 50 55 60 70 80 90 100Fallaway allowance f0,90 1,02 1,12 1,18 1,39 1,56 1,98 2,35 2,75 3,11 3,53 3,92All gauging is performed with reference to the top surface of the head. In the case of oval or

31、round top heads, measurements are taken from the actual intersection of the top surface of the head and the hexalobular internal driving feature counterbore.When using a dial penetration gauge, this should be adjusted to zero while the gauge is pressed against a flat surface, thereby compressing the

32、 plunger to make it flush with the gauge reference surface (see Figure 2).Figure 2 Dial gauge (zero position)3.2 GO gaugeThe GO gauge dimensions (see Figure 3) shall be within the limits specified in Table 3. ISO 2014 All rights reserved 3BS EN ISO 10664:2014ISO 10664:2014(E)aRadius max. 0,076 mm at

33、 juncture of side and face to gauge sizes no. 10 and max. 0,025 4 mm for gauge sizes no. 10.Figure 3 Dimensions of GO gaugeTable 3 Limiting sizes of GO gauge dimensionsDimensions in millimetresSocket no.A B RiReHmin. max. min. max. min. max. min. max. min. max.1 0,841 0,855 0,592 0,607 0,198 0,204 0

34、,055 0,062 0,64 1,142 0,953 0,967 0,674 0,688 0,221 0,227 0,065 0,072 1,15 1,653 1,131 1,145 0,800 0,815 0,263 0,270 0,078 0,085 1,15 1,654 1,291 1,305 0,912 0,927 0,305 0,312 0,087 0,093 1,15 1,655 1,415 1,430 1,013 1,028 0,318 0,342 0,107 0,111 1,15 1,656 1,695 1,709 1,210 1,224 0,371 0,396 0,130

35、0,134 1,33 1,827 2,012 2,026 1,437 1,453 0,442 0,450 0,157 0,165 2,54 3,058 2,335 2,349 1,672 1,686 0,498 0,523 0,188 0,193 2,54 3,059 2,520 2,534 1,809 1,823 0,542 0,566 0,204 0,210 2,79 3,3010 2,761 2,776 1,979 1,993 0,585 0,609 0,227 0,231 3,05 3,5615 3,295 3,309 2,353 2,367 0,704 0,728 0,265 0,2

36、69 3,30 3,8120 3,879 3,893 2,764 2,778 0,846 0,871 0,303 0,307 3,56 4,0725 4,451 4,465 3,170 3,185 0,907 0,932 0,371 0,378 3,94 4,4527 5,009 5,024 3,564 3,578 1,095 1,120 0,387 0,393 4,19 4,7030 5,543 5,557 3,958 3,972 1,182 1,206 0,448 0,454 4,44 4,9540 6,673 6,687 4,766 4,780 1,415 1,440 0,544 0,5

37、48 5,08 5,5945 7,841 7,856 5,555 5,570 1,784 1,808 0,572 0,576 5,71 6,2250 8,857 8,872 6,366 6,380 1,804 1,828 0,773 0,777 5,97 6,4855 11,245 11,259 7,930 7,945 2,657 2,682 0,765 0,769 6,22 6,7360 13,302 13,317 9,490 9,504 2,871 2,895 1,065 1,069 7,68 8,1770 15,588 15,603 11,085 11,099 3,465 3,489 1

38、,192 1,196 8,46 8,9680 17,619 17,635 12,646 12,661 3,625 3,629 1,524 1,529 9,4 9,990 20,021 20,035 14,232 14,246 4,456 4,480 1,527 1,534 10,06 10,56100 22,231 22,245 15,820 15,834 4,913 4,937 1,718 1,724 10,85 11,354 ISO 2014 All rights reservedBS EN ISO 10664:2014ISO 10664:2014(E)3.3 NO GO gauge3.3

39、.1 Gauging the fallaway of dimensions A and ReThe NO GO gauge for dimensions A and Re(see Figure 4) shall have dimensions within the limits specified in Table 4.aRadius max. 0,076 mm at juncture of side and face for gauge sizes no. 10 and max. 0,025 4 mm for gauge sizes no. 10.Figure 4 NO GO gauge f

40、or dimensions A and ReTable 4 Limiting sizes of dimensions of NO GO gauge for dimensions A and ReDimensions in millimetresSocket no.A B RiReHmin. max. max. min. max. min. max. 0,251 0,899 0,907 0,587 0,107 0,114 0,084 0,094 0,892 1,011 1,019 0,663 0,124 0,132 0,094 0,104 1,43 1,214 1,222 0,790 0,137

41、 0,145 0,119 0,130 1,44 1,374 1,382 0,917 0,180 0,191 0,132 0,140 1,45 1,499 1,506 1,044 0,208 0,221 0,147 0,157 1,46 1,778 1,785 1,181 0,231 0,241 0,173 0,180 1,577 2,096 2,103 1,359 0,259 0,267 0,203 0,211 2,88 2,419 2,425 1,664 0,360 0,370 0,231 0,238 2,799 2,604 2,611 1,664 0,323 0,333 0,248 0,2

42、57 3,0510 2,845 2,852 1,956 0,431 0,441 0,269 0,276 3,315 3,379 3,385 1,956 0,398 0,408 0,307 0,315 3,5620 3,963 3,970 2,616 0,602 0,614 0,345 0,353 3,8125 4,560 4,566 2,868 0,637 0,647 0,429 0,436 4,1927 5,118 5,126 3,275 0,735 0,747 0,445 0,452 4,4530 5,652 5,659 3,886 0,939 0,949 0,505 0,513 4,74

43、0 6,807 6,814 4,661 1,112 1,125 0,612 0,619 5,3345 7,976 7,983 4,661 1,110 1,123 0,640 0,648 5,9750 8,992 8,999 6,413 1,628 1,640 0,840 0,848 6,2255 11,405 11,412 7,684 2,176 2,189 0,845 0,853 6,4860 13,488 13,495 7,684 2,153 2,164 1,158 1,165 7,9270 15,774 15,781 10,262 2,545 2,557 1,285 1,292 8,71

44、80 17,831 17,838 11,760 2,608 2,621 1,628 1,635 9,52 ISO 2014 All rights reserved 5BS EN ISO 10664:2014ISO 10664:2014(E)Socket no.A B RiReHmin. max. max. min. max. min. max. 0,2590 20,257 20,264 12,827 3,111 3,121 1,648 1,656 10,31100 22,467 22,473 15,240 4,006 4,018 1,839 1,847 11,103.3.2 Gauging t

45、he fallaway of dimension BSee Figure 5.Figure 5 Cylindrical zone to be gaugedA cylindrical NO GO gauge with diameter as specified in Table 5 shall not enter the hexalobular internal driving feature to a depth greater than the fallaway allowance specified in Table 2.Table 5 Diameter of cylindrical NO

46、 GO gauge for dimension BDimensions in millimetresSocket no.Diameter of cylindrical NO GO gaugemin. max.1 0,720 0,7252 0,810 0,8153 0,960 0,9654 1,100 1,1055 1,200 1,2056 1,440 1,4457 1,710 1,7158 1,920 1,9259 2,140 2,14510 2,280 2,28515 2,760 2,76520 3,280 3,28525 3,720 3,72527 4,260 4,26530 4,660

47、4,66540 5,600 5,605Table 4 (continued)6 ISO 2014 All rights reservedBS EN ISO 10664:2014ISO 10664:2014(E)Socket no.Diameter of cylindrical NO GO gaugemin. max.45 6,660 6,66550 7,380 7,38555 9,660 9,66560 11,340 11,34570 13,340 13,34580 14,920 14,92590 17,160 17,165100 19,020 19,0254 DesignationThe d

48、esignation shall make reference to this International Standard and the socket number.EXAMPLE A hexalobular internal driving feature, socket no. 20, is designated as follows:Hexalobular internal driving feature ISO 10664 20Table 5 (continued) ISO 2014 All rights reserved 7BS EN ISO 10664:2014ISO 1066

49、4:2014(E)Annex A (informative) Representation of hexalobular internal driving feature contourThe correlations of dimensions given in Figure A.1 are intended to support the drawing of the driving feature only, e.g. when using a CAD system.KeyB approximately 0,72 Areapproximately 0,1 Ariapproximately 0,175 AaThe circle is tangential to the socket contour at points 1, 2, and 3.Figure A.1 Representation of hexalobular internal driving feature8 ISO 2014 All rights reservedBS EN ISO 10664:2014This page deliberately