EN ISO 2338-1997 en Parallel Pins of Unhardened Steel and Austenitic Stainless Steel《不淬硬钢和奥氏体不锈钢圆锥销ISO 2338-1997》.pdf

《EN ISO 2338-1997 en Parallel Pins of Unhardened Steel and Austenitic Stainless Steel《不淬硬钢和奥氏体不锈钢圆锥销ISO 2338-1997》.pdf》由会员分享，可在线阅读，更多相关《EN ISO 2338-1997 en Parallel Pins of Unhardened Steel and Austenitic Stainless Steel《不淬硬钢和奥氏体不锈钢圆锥销ISO 2338-1997》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、STD-BSI BS EN IS0 2338-ENGL 1998 lb2qbb9 b97654 blb BRITISH STANDARD Parallel pins of unhardened steel and austenitic stainless steel The European Standard EN IS0 2338 : 1997 has the status of a British Standard ICs 21.060.60 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS

2、EN IS0 2338 : 1998 uum - STD.BS1 BS EN IS0 2338-ENGL 1778 1b24bb7 Ob77b55 552 Amd.No. BS EN IS0 2338 : 1998 Date Text affected National foreword This British Standard is the English anguage version of EN IS0 2338 : 1997. It is identical with IS0 2338 : 1997. It supersedes BS EN 22338 : 1992 which is

3、 withdrawn. The TJK participation in its preparation was entrusted by Technical Committee FMEY9, Bolts, nuts and accessories, to Subcommittee FME/9/6, General puropse fasteners and accessories, which has the responsibfity to: - aid enquirers to understand the text; - present to the responsible inter

4、nationalEuropean committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; - monitor related international and European developments and promulgate them in the UX. A list of organizations represented on this subcommittee can be obtained on request to

5、 its secretary. Cross-references Attention is drawn to the fact that CEN and CENELEC Standaxis normally include an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement these intrnationai or European

6、 publications may be found in the BSI Standards Catalogue under the section entitled International Standards Correspondence Index, or by using the Find facility of the BSI Standards Electronic Catalogue. Compliance with a British Standard does not of itself confer immunity from legal obligations. Su

7、mmary of pages This document comprises a front cover, an inside front cover, the EN IS0 title page, the EN IS0 foreword page, the IS0 title page, page ii, pages 1 to 3 and a back cover. This British Standard, having been prepared under the direction of the Engineering Sector Board, was published und

8、er the authority of the Standards Board and comes into effect on 15 May 1998 O BSI 1998 ISBN O 580 29089 1 EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN IS0 2338 November 1997 ICs 21.060.50 Descriptors: see IS0 document Supersedes EN 22338:1992 English version Parallel pins, of unhardened ste

9、el and austenitic stainless steel (IS0 2338: 1 997) oupilles cyiindfiques en acier non trem et en acier inoxydable austnitique (IS0 2338:1997) Zylinderstlfle au8 ungehhrtelem Stahl und austenilischem nichtrostendem Stahl (IS0 2338:1997) Thk European Standard was approved by CEN on 23 October 1907. C

10、EN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this European Standard lhe status of a nalional standard without any alteration. Upla-date lists and bibliographicel references concerning such national standerda may be obtained on appl

11、ication to the Central Secretarial or to any CEN member. This European Standard exlsW1 in three offidal versions (English, French, erman). A version in any dher language made by translalion under lhe responsibility of a CEN member into its own language and notified to the Central Secretariat has the

12、 same status as he official vereims. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, ermany, ireece, Iceland, Ireland, hay, Luxembourg, Netheilands, Noway, Porlugal, Spain, Sweden, Switzeriand and United Kingdom. EUROPEAN COMhlTTEE FOR STA

13、NDARDEAiON COMITE EUROPEEN DE NORMALISATION EUROPISCHES KOMITEE FOR NORMUNG Central Secretariat: rue da Susrart, 36 81050 Brusreh (B 1997 CEN All tights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN IS0 23383997 E I STD-BSI BS EN IS0 2338-ENGL

14、1998 m 1b2Libh9 Ob77b57 325 m EN IS0 23381997 Foreword The text of the International Standard IS0 2338:1997 has been prepared by Technical Committee ISO/TC 2 “Fasteners“ in collaboration with Technical Committee CEN/TC 185 “Threaded and non-threaded mechanical fasteners and accessories“, the secreta

15、riat of which is held by DIN. This European Standard supersedes EN 22338:1992. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 1998, and conflicting national standards shall be withdrawn at th

16、e latest by May 1998. According to the CENICENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Ne

17、therlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of the International Standard IS0 2338:1997 was approved by CEN as a European Standard without any modification. STD-BSI BS EN IS0 2338-ENGL 1778 D Lb2qbb7 Ob97b58 2b1 EN IS0 2338:1997 INTERNA

18、TIONAL STANDARD IS0 2338 Second edition 1997-11-01 Parallel pins, of unhardened steel and austenitic stainless steel Goupilles cylindriques en acier non tremp er en acier inoxydable ausrnirique Reference number IS0 2338:1997(E) STD-BSI BS EN IS0 2338-ENGL 1778 lb2Libb7 Ob77b59 IT8 W EN IS0 2338:1997

19、 Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees. Each member body interested in a subject for which a

20、technical committee has been established has the right to be represented on that committee. International organizations, governmental and non- governmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matte

21、rs of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard IS0 2338 w

22、as prepared by Technical Committee ISO/TC 2, fasteners. This second edition cancels and replaces the first edition (IS0 2338:1986), which has been technically revised. Descriptors: fasteners, Steel products, pins (mechanics), straight pins, specifications, characteristics, dimensions, designation. i

23、 STD-BSI BS EN IS0 2338-ENGL 1798 = lb2LIbb7 Ob77bb0 9LT H EN IS0 2338:1997 Parallel pins, of unhardened steel and austenitic stainless steel 1 scope This International Standard specifies the characteristics of parallel pins of unhardened steel and austenitic stainless steel, with nominal diameters

24、d from 0,6 mm to 50 mm inclusive. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and p

25、arties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and IS0 maintain registers of currently valid International Standards. = _. rn IS0 3269: 1988, Fasteners - Acc

26、eptance inspection. IS0 3506-1: 1997, Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs. = II * v: IS0 4042:-?, Fasteners - Electroplated coatings. IS0 9717:1990, Phosphate conversion coatings for metals - Method of specifying requirements. 3 Di

27、mensions See figure 1 and table 1. Optional end shape at the manufacturer?s discretion i) Radius and dimpled pin end permissible Figure 1 1) To be published. (Revision of IS0 4042:1989) 1 I EN IS0 2338:1997 sTD.BSI BS EN IS0 2338-ENGL 1798 Lb29bb Ob77bbL 85b 1) Other tolerances as agreed between cus

28、tomer and supplier. 2) For nominal lengths above 200 mm, steps of 20 mm. 2 STD-BSI BS EN IS0 2338-ENGL 1998 W LbZqbbS 0697bb2 792 = EN IS0 2338:1997 Acceptability 4 Requirements and reference International Standards See table 2. The acceptance procedure is covered in IS0 3269. Table 2 - Requirements

29、 and reference International Standards Matenal” Steel (Sti Hardness 125 HV30 to 245 HV30 Surface finish Surface roughness Plain, .e. pins to be supplied in natural finish treated with a protective lubricant, unless otherwise specified by agreement between customer and supplier. Preferred coatings ar

30、e black oxide, phosphate coating or zinc plating with chromate conversion coating (see IS0 9717 and IS0 4042). Other coatings as agreed between customer and supplier. All tolerances shall apply prior to the ap- plication of a plating or coating. For pins with tolerance class m6: R, s 0,8 pm For pins

31、 with tolerance class h8: Ra d 1,6 pm Austenitic stainless steel AI in accordance with IS0 3506-1, hardness 210 HV30 to 280 HV30 Plain, .e. pins to be supplied in natural finish. 1 Pins shall be free of irregularities or detrimental defects. I No burrs shall appear on any part of the pin. Workmanshi

32、p 5 Designation EXAMPLE 1 An unhardened steel parallel pin, with nominal diameter d = 6 mm, tolerance class m6 and nominal length i = 30 rnm is designated as follows: Parallel pin IS0 2338 - 6 m6 x 30 - St EXAMPLE 2 An unhardened austenitic stainless steel pin of grade AI, with nominal diameter d= 6

33、 mm, tolerance class m6 and nominal length I = 30 mm is designated as follows: Parallel pin IS0 2338 - 6 m6 x 30 - Al 3 BS EN IS0 2338 : 1998 BSI 389 Chiswick High Road London w4 4AL BSI - British Standards Institution BSI is the independent national body responsible for preparing British Standards.

34、 It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Contract requirements A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct applicati

35、on. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccura

36、cy or ambiguity while using this British Standard would inform the Secretary of the responsible technical committee, the identity of which can be found on the inside front cover. Tel: 0181 996 9000; Fax: 0181 996 7400. BSI offers members an individual updating service called PLUS which ensures that

37、subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services, Sales Department at Chiswick Tel: 0181 996 7000, Fax: 0181 996 7001. In response to orders for internati

38、onal standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Libmy, the Standardhe

39、Database, the BSI Infomation Technology Service (BITS) and its Technical Help to Exporters Service. Contact the Information Department at Chiswick Tel: 0181 996 7111; Fax: 0181 996 7048. Subscribing members of BI are kept up to date with standards developments and receive substantial discounts on th

40、e purchase price of standards. For details of these and other benefits contact Customer Services? Membership at Chiswick Tel: 0181 996 7002, Fax: 0181 996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the intedonal standar

41、dization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no exkact may be reproduced, stored in a retried system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission from BI. This does not precl

42、ude the free use, in the com of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained if permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager, BSI, 389 Chiswick High Road, London W4 4AL