EN 62733-2015 en Programmable components in electronic lamp controlgear - General and safety requirements.pdf

《EN 62733-2015 en Programmable components in electronic lamp controlgear - General and safety requirements.pdf》由会员分享，可在线阅读，更多相关《EN 62733-2015 en Programmable components in electronic lamp controlgear - General and safety requirements.pdf（46页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationProgrammable components in electronic lamp controlgear General and safety requirementsBS EN 62733:2015National forewordThis British Standard is the UK implementation of EN 62733:2015. It is identical to IEC 62733:2015.The UK participation in its preparation was entrusted by

2、TechnicalCommittee CPL/34, Lamps and Related Equipment, to SubcommitteeCPL/34/3, Auxiliaries for lamps.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users are re

3、sponsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 75727 3ICS 29.140.99Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStanda

4、rds Policy and Strategy Committee on 31 July 2015.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 62733:2015EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 62733 June 2015 ICS 29.140.99 English Version Programmable components in electronic lamp controlgear

5、- General and safety requirements (IEC 62733:2015) Composants programmables dans les appareillages lectroniques de lampes - Exigences gnrales et exigences de scurit (IEC 62733:2015) Programmierbare Bauteile von elektronischen Betriebsgerten fr Lampen - Teil 1: Allgemeine und Sicherheitsanforderungen

6、 (IEC 62733:2015) This European Standard was approved by CENELEC on 2015-06-11. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists an

7、d bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under

8、the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Eston

9、ia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee f

10、or Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Me

11、mbers. Ref. No. EN 62733:2015 E BS EN 62733:2015EN 62733:2015 2 European foreword The text of document 34C/1140/FDIS, future edition 1 of IEC 62733, prepared by SC 34C, “Auxiliaries for lamps“, of IEC TC 34, “Lamps and related equipment“, was submitted to the IEC-CENELEC parallel vote and approved b

12、y CENELEC as EN 62733:2015. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2016-03-11 latest date by which the national standards conflicting with the document have to b

13、e withdrawn (dow) 2018-06-11 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard

14、 IEC 62733:2015 was approved by CENELEC as a European Standard without any modification. BS EN 62733:2015EN 62733:2015 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normativel

15、y referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified by commo

16、n modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 61000-4-13 2002 Electromagnetic compatibility (EMC) - Part 4-1

17、3: Testing and measurement techniques - Harmonics and interharmonics including mains signalling at a.c. power port, low frequency immunity tests EN 61000-4-13 2002 + A1 2009 + A1 2009 IEC 61347-1 - Lamp controlgear - Part 1: General and safety requirement EN 61347-1 - IEC 61347-2 series Lamp control

18、gear EN 61347-2 series IEC 61508-4 2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 4: Definitions and abbreviations EN 61508-4 2010 IEC 61508-5 2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part

19、5: Examples of methods for the determination of safety integrity levels EN 61508-5 2010 IEC 61508-7 2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 7: Overview of techniques and measures EN 61508-7 2010 IEC 61547 2009 Equipment for general lighti

20、ng purposes - EMC immunity requirements EN 61547 2009 BS EN 62733:2015 2 IEC 62733:2015 IEC 2015 CONTENTS FOREWORD . 4 INTRODUCTION . 6 1 Scope 7 2 Normative references 7 3 Terms and definitions 7 4 General requirements 10 5 Risk assessment . 11 5.1 General . 11 5.2 Specification of tolerable risk 1

21、1 5.3 Documentation 11 6 Requirements for abnormal operating and fault conditions . 12 6.1 Abnormal operating and fault conditions in the application of the electronic lamp controlgear . 12 6.2 Fault conditions for the programmable component 12 7 Requirements for software . 13 8 Requirements for EMC

22、 immunity 13 Annex A (normative) Software evaluation . 15 A.1 General . 15 A.2 Protective programmable components using software 15 A.3 Terms and definitions 15 A.4 Requirements for the architecture . 22 A.5 Measures to avoid errors 30 Annex B (informative) FTA and FMEA analysis 34 B.1 FTA results .

23、 34 B.2 FMEA results 35 Annex C (informative) Guidance on the identification of a protective programmable component 37 Annex D (normative) Risk classification . 38 D.1 General . 38 D.2 Frequency of occurrence. 38 D.3 Risk severity . 38 D.4 Classification of risks 39 Bibliography 40 Figure B.1 Exampl

24、e of a fault tree diagram 35 Table A.1 General fault/error conditions . 24 Table A.2 Specific fault/error conditions 26 Table A.3 Semi-formal methods . 31 Table A.4 Software architecture specification . 31 Table A.5 Module design specification . 32 Table A.6 Design and coding standards . 33 Table A.

25、7 Software safety validation 33 Table D.1 Frequency definition and categorization (from IEC 61508-5:2010 Annex C) 38 BS EN 62733:2015IEC 62733:2015 IEC 2015 3 Table D.2 Risk severity definitions (from IEC 61508-5:2010, Annex C) 38 Table D.3 Safety risk classification 39 BS EN 62733:2015 4 IEC 62733:

26、2015 IEC 2015 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ PROGRAMMABLE COMPONENTS IN ELECTRONIC LAMP CONTROLGEAR GENERAL AND SAFETY REQUIREMENTS FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical co

27、mmittees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Techni

28、cal Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, government

29、al and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agr

30、eements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use

31、 and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promo

32、te international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indica

33、ted in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6)

34、All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage

35、 or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this public

36、ation. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all suc

37、h patent rights. International Standard IEC 62733 has been prepared by subcommittee 34C: Auxiliaries for lamps, of IEC technical committee 34: Lamps and related equipment. The text of this standard is based on the following documents: FDIS Report on voting 34C/1140/FDIS 34C/1156/RVD Full information

38、 on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. NOTE In this standard the following print types are used: Requirements proper: in Roman type. BS EN

39、 62733:2015IEC 62733:2015 IEC 2015 5 Test specifications: in Italic type. Explanatory matter: in smaller roman type. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data

40、related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. BS EN 62733:2015 6 IEC 62733:2015 IEC 2015 INTRODUCTION This International Standard provides safety requirements and test methods for programmable components

41、when in electronic lamp controlgear. It provides additional safety requirements for electronic lamp controlgear containing programmable components to the requirements of IEC 61347 series. In general, the two means of protection safety principle is used for protection against hazards such as electric

42、 shock. Consequently one single fault condition or abnormal operation of the electrical equipment will not lead to a hazardous situation. Until recent technology, two means of protection have been realized in traditional hardware. Examples are the provision of basic insulation and supplementary insu

43、lation between hazardous live parts and accessible parts, and provision of basic insulation combined by disconnection of the mains supply by a fuse. Nowadays however programmable components (with embedded software) may be used as a measure to provide safety under normal conditions, single fault cond

44、itions and/or abnormal operation. Since the traditional lighting standards do not provide requirements for programmable components, this standard has been drawn up. This standard recognizes the internationally accepted level of protection against hazards such as electrical, mechanical, thermal, fire

45、 and radiation of appliances when operated as in normal use taking into account the manufacturers instructions. It also covers conditions for electromagnetic phenomena that can be expected in practice with influence on the operation of the programmable component, for taking into account the way this

46、 can affect the safe operation of the electronic lamp controlgear. This first edition is based upon IEC 60730-1:2010 and IEC 60335-1:2010 and adapted for electronic lamp controlgear NOTE The terms and definitions and Tables A.1 and A.2 respectively of this standard are equivalent to terms and defini

47、tions and Table R.1 and R.2 of IEC 60335-1:2010, and equivalent terms and definitions and Table H.1 (class B and class C software) of IEC 60730-1:2010. BS EN 62733:2015IEC 62733:2015 IEC 2015 7 PROGRAMMABLE COMPONENTS IN ELECTRONIC LAMP CONTROLGEAR GENERAL AND SAFETY REQUIREMENTS 1 Scope This Intern

48、ational Standard provides general and safety requirements for programmable components used in products covered by IEC 61347. The requirements of this standard are only applicable to the programmable components (including its embedded software) in the electronic lamp controlgear. For other electric/e

49、lectronic circuits and their components in the electronic lamp controlgear, the requirements of IEC 61347 series apply. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61000-4-13:2002, Electromagneti