EN 61347-2-1-2001 en Lamp controlgear - Part 2-1 Particular requirements for starting devices (other than glow starters) (Incorporating Corrigenda July 2003 November 2006 and Decem.pdf

《EN 61347-2-1-2001 en Lamp controlgear - Part 2-1 Particular requirements for starting devices (other than glow starters) (Incorporating Corrigenda July 2003 November 2006 and Decem.pdf》由会员分享，可在线阅读，更多相关《EN 61347-2-1-2001 en Lamp controlgear - Part 2-1 Particular requirements for starting devices (other than glow starters) (Incorporating Corrigenda July 2003 November 2006 and Decem.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN61347-2-1:2001+A1:2006 Incorporatingcorrigenda Lamp controlgear Part 2-1: Particular requirements for starting devices (other than glow starters)ICS 29.140.99g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g

2、54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58September 2003,January 2007and December 2010BS EN +A2:2014Incorporating corrigenda September 2003, January 2007 and December 2010BS EN 61347-2-1:2001+A2:2014ISBN 978 0 580 74466 2Amendments/corrigenda issued since publica

3、tionAmd. No. Date Comments14668 Corrigendum No. 126 September 2003 Change to date of withdrawal in EN foreword16325 31 May 200616837 Corrigendum No. 229 January 2007 Change to EN foreword and Annex ZA31 March 2011 Modification of CENELEC foreword31 May 2014 Implementation of IEC amendment 2:2013 wit

4、h CENELEC endorsement A2:2014. Annex ZA amendedThis British Standard, having been prepared under the direction of the Electrotechnical Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 May 2001 The British Standards Institution 2014. Published

5、 by BSI Standards Limited 2014National forewordThis British Standard is the UK implementation of EN 61347-2-1:2001+A2:2014, incorporating corrigenda July 2003, November 2006 and December 2010. It is identical to IEC 61347-2-1:2000, incorporating amendments 1:2005 and 2:2013. It supersedes BS EN 6134

6、7-2-1:2001+A1:2006, which will be withdrawn on 30 October 2016.The start and finish of text introduced or altered by amendment is indicated in the text by tags. Tags indicating changes to IEC text carry the number of the IEC amendment. For example, text altered by IEC amendment 1 is indicated by .Th

7、e UK participation in its preparation was entrusted by Technical Committee CPL/34, Lamps and Related Equipment, to Subcommittee CPL/34/3, Auxiliaries for lamps.A list of organizations represented on this subcommittee can be obtained on request to its secretary.This publication does not purport to in

8、clude all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMCENELECEuropean Committee for Electrotechnical StandardizationComit Euro

9、pen de Normalisation ElectrotechniqueEuropisches Komitee fr Elektrotechnische NormungCentral Secretariat: 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.ICS 29.140.99 English versionLamp controlgear nullPart 2-1: Particular requirements

10、for starting devices(other than glow starters)(IEC 61347-2-1:2000)Appareillages de lampes nullPartie 2-1: Prescriptions particulirespour les dispositifs damorage(autres que starters lueur)(CEI 61347-2-1:2000)Gerte fr Lampen nullTeil 2-1: Besondere Anforderungen anStartgerte (andere als Glimmstarter)

11、(IEC 61347-2-1:2000)Up-to-date lists and bibliographical references concerning such national standards may be obtained onapplication to the Central Secretariat or to any CENELEC member.This European Standard exists in three official versions (English, French, German). A version in any otherlanguage

12、made by translation under the responsibility of a CENELEC member into its own language andnotified to the Central Secretariat has the same status as the official versions.ORUENAEP DNATSADRENNEPORUE EMRONIPORUEMRON EHCS aJunray 2001CELENECruEopean Commeetti for elEcrtotcenhcial tSnaradidaztinomoCiE t

13、ruoped ne Nromsilataino ElcertotcehniqeuruEposicseh Kmoif eetr lEkerttocehsinceh roNmgnueCntlar erceStirata: ure de tSrassat 53B , - rB 0501uessslEC 1002 ENLE- C All irhgts fo xelpiotatii non yna fomr dna yna yb mnaes ersew devrolrwdi f edoEC rENELm Cemrebs.feR. .oN EN :1-74316E 1002silgnErev hsnoip

14、maL tnocrolgear null Patr :1 eGneral dna safety meriuqerentsappAralliegel ed sampes nullraPite 1rP :rcseipitong srnlae setrprcseipited sno srucit(C316 IE-74:102)00eGrrf et Lampen Ti l 1: lAlgmeieen dnuiSrehciehstnarofredungen(ICE 316-74:102)00hTsi uEpornae tSdnaraw das ppaordev by CENELEC no 2-00011

15、0-1. CENELEC members are dnuoboitacilppaC eht ot ntairaterceS lartne yna ot ro CENECEL .rebmemTsih European Standard xestsi aiciffo eerht nil vsilgnE( snoisreh, G ,hcnerFv A .)namreyna ni noisre rehtoegaugnal amed yb noitalsnart nured nopser ehtlibisiyt C a foENECEL ti otni rebmemwo sdna egaugnal nC

16、 eht ot deifitonterceS lartneeht sah taira emas a sutatss ffo ehtiv laic.snoisreCENELEC members are the national electrotechnical committees irtsuA foC ,muigleB ,azR hceilbupec,comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the statu

17、s of a national standard without any alteration.Ref. No. EN 61347-2-1:2001 ECENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembour

18、g, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Switzerland and the United Kingdom.Spain, Sweden, This European Standard was approved by CENELEC on 2002-11-01. CENELEC members are bound to EN 61347-2-1:2001+A1January 2001I n c o r p o r a t i n g Corrigenda July 200

19、3, November 2006 and December 2010.Avenue Marnix 17, B-1000 Brussels EN 61347-2-1:2001+A2February 2014ForewordThe text of document 34C/498/FDIS, future edition 1 of IEC 61347-2-1, prepared by SC 34C, Auxiliariesfor lamps, of IEC TC 34, Lamps and related equipment, was submitted to the IEC-CENELEC pa

20、rallel voteand was approved by CENELEC as EN 61347-2-1 on 2000-11-01.This European Standard, together with EN 61347-1, supersedes EN 60926:1996 + A1:1999.The following dates were fixed: latest date by which the EN has to be implementedat national level by publication of an identicalnational standard

21、 or by endorsement (dop) 2001-08-01 latest date by which the national standards conflictingwith the EN have to be withdrawn (dow) 2006-12-01This standard shall be used in conjunction with EN 61347-1.NOTE In this standard, the following print types are used:- requirements: in roman type;- test specif

22、ications: in italic type;- notes: in smaller roman type.Annexes designated “normative“ are part of the body of the standard.In this standard, annexes A to J and ZA are normative.Annex ZA has been added by CENELEC._Endorsement noticeThe text of the International Standard IEC 61347-2-1:2000 was approv

23、ed by CENELEC as a EuropeanStandard without any modification._Page 2Foreword to amendment A1The text of document 34C/697/FDIS, future amendment 1 to IEC 61347-2-1:2000, prepared by SC 34C, Auxiliaries for lamps, of IEC TC 34, Lamps and related equipment, was submitted to the IEC-CENELEC parallel vot

24、e and was approved by CENELEC as amendment A1 to EN 61347-2-1:2001 on 2006-02-01. The following dates were fixed: latest date by which the amendment has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2006-11-01 latest date by which the na

25、tional standards conflicting with the amendment have to be withdrawn (dow) 2009-02-01 This European Standard makes reference to International Standards. Where the International Standard referred to has been endorsed as a European Standard or a home-grown European Standard exists, this European Stand

26、ard shall be applied instead. Pertinent information can be found on the CENELEC web site. _ Endorsement notice The text of amendment 1:2005 to the International Standard IEC 61347-2-1:2000 was approved by CENELEC as an amendment to the European Standard without any modification. _ BS EN 61347-2-1:20

27、01+A1:2006EN 61347-2-1:2001+A1:2006 (E)Page 2BS EN 61347-2-1:2001+A2:2014EN 61347-2-1:2001+A2:2014 (E)EN 61347-2-1:2001/A2:2014 - 2 - Foreword The text of document 34C/1051/FDIS, future IEC 61347-2-1:2000/A2, prepared by SC 34C “Auxiliaries for lamps“ of IEC/TC 34 “Lamps and related equipment“ was s

28、ubmitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61347-2-1:2001/A2:2014. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2014-07-30 latest date by

29、which the national standards conflicting with the document have to be withdrawn (dow) 2016-10-30 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such pate

30、nt rights. Endorsement notice The text of the International Standard IEC 61347-2-1:2000/A2:2013 was approved by CENELEC as a European Standard without any modification. Page 3BS EN 61347-2-1:2001+A2:2014EN 61347-2-1:2001+A2:2014 (E)EN 61347-2-1:2001/A2:2014 - 2 - Foreword The text of document 34C/10

31、51/FDIS, future IEC 61347-2-1:2000/A2, prepared by SC 34C “Auxiliaries for lamps“ of IEC/TC 34 “Lamps and related equipment“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61347-2-1:2001/A2:2014. The following dates are fixed: latest date by which the document has to be

32、 implemented at national level by publication of an identical national standard or by endorsement (dop) 2014-07-30 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2016-10-30 Attention is drawn to the possibility that some of the elements of this d

33、ocument may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 61347-2-1:2000/A2:2013 was approved by CENELEC as a European Standard without any modification. F

34、oreword to amendment A2Ge3 BSI 05-2001CONTENTSPageINTRODUCTION 5Clause1 Scope 62 Normative references. 63 Definitions 74 General requirements. 75 General notes on tests . 85.1 Starting devices for use with lamps having different electrical characteristics. 85.2 Number of specimens . 86 Classificatio

35、n . 87 Marking 87.1 Mandatory markings 87.2 Information to be provided, if applicable 88 Protection against accidental contact with live parts 99 Terminals. 910 Provisions for earthing . 911 Moisture resistance and insulation 912 Electric strength. 913 Thermal endurance test for windings .1014 Fault

36、 conditions.1015 Heating of independent starting devices 1015.1 Normal operation .1115.2 Abnormal operation1116 Pulse voltage of ignitors 1217 Mechanical strength 1218 Construction .1219 Creepage distances and clearances 1320 Screws, current-carrying parts and connections.1321 Resistance to heat, fi

37、re and tracking1322 Resistance to corrosion.13Annex A (normative) Test to establish whether a conductive part is a live part which may causean electric shock .14Annex B (normative) Particular requirements for thermally protected lamp controlgear .14Annex C (normative) Particular requirements for ele

38、ctronic lamp controlgear with means ofprotection aginst overheating.14Annex D (normative) Requirements for carrying out the heating tests of thermally protectedlamp controlgear .14Annex E (normative) Use of constant S other than 4 500 in tw tests14Annex G (informative) Explanation of the derivation

39、of the values of pulse voltages15Page 3Annex F (normative) Draught-proof enclosure15BS EN 61347-2-1:2001+A1:2006EN 61347-2-1:2001+A1:2006 (E)Ge3 BSI 05-2001CONTENTSPageINTRODUCTION 5Clause1 Scope 62 Normative references.3 Definitions 74 General requirements.5 notes on tests . 85.1 Starting devices f

40、or use with lamps having different electrical characteristics.5.2 Number of specimens .6 Classification .7 M rking7.1 Mandatory markings7.2 Information to be provided, if applicable 8 Protection against accidental contact with live parts 99 Terminals.10 Provisions for earthing .11 Moisture resistanc

41、e and insulation12 Electric strength.13 Thermal endurance test for windings .1014 Fault conditions.1015 Heating of independent starting devices 1015.1 Normal operation .1115.2 Abnormal operation1116 Pulse voltage of ignitors 1217 Mechanical strength 1218 Construction .1219 Creepage distances and cle

42、arances 1320 Screws, current-carrying parts and connections.1321 Resistance to heat, fire and tracking1322 Resi tance to corrosion.13Annex A (normative) Test to establish whether a conductive part is a live part which may causean electric shock .14Annex B (normative) Particular requirements for ther

43、mally protected lamp controlgear .14C ( t r f electronic lamp controlgear with means ofprotection aginst overheating.14Annex D (normative) Requirements for carrying out the heating tests of thermally protectedlamp controlgear .14Annex E (normative) Use of constant S other than 4 500 in tw tests14G (

44、informative) Explanation of the derivation of the values of pulse voltages15Page 3F ative) Draught-proof enclosure15BS EN 61347-2-1:2001+A1:2006EN 61347-2-1:2001+A1:2006 (E)Page 4BS EN 61347-2-1:2001+A2:2014EN 61347-2-1:2000+A2:2014Heating of built-in and independent starting devices15.1 General 15.

45、2 Normal operation 15.3 Abnormal operation 677899999991010101010101111111112131515161616171718181818181919Ge3 BSI 05-2001Annex H (normative)15Annex I (normative) Mechanical strength testing 16Annex ZA (normative) Normative references to international publications with theircorresponding European pub

46、lications 21Bibliography 20Figure 1 Starting voltage measurement for ignitors .13Figure I.1 Tumbling barrel.17Page 4Annex J (normative) Precautions to be observed when measuring with sphere-gaps 18BS EN 61347-2-1:2001+A1:2006EN 61347-2-1:2001+A1:2006 (E)Page 5BS EN 61347-2-1:2001+A2:2014EN 61347-2-1

47、:2000+A2:201419202224231721Ge3 BSI 05-2001INTRODUCTIONThis first edition of IEC 61347-2-1, published in conjunction with IEC 61347-1, represents aneditorial review of IEC 60926. The formatting into separately published parts provides for easeof future amendments and revisions. Additional requirement

48、s will be added as and when aneed for them is recognized.This standard, and the parts which make up IEC 61347-2, in referring to any of the clauses ofIEC 61347-1, specify the extent to which such a clause is applicable and the order in which thetests are to be performed; they also include additional

49、 requirements, as necessary. All partswhich make up IEC 61347-2 are self-contained and, therefore, do not include references toeach other.Where the requirements of any of the clauses of IEC 61347-1 are referred to in this standardby the phrase ”The requirements of clause n of IEC 61347-1 apply”, this phrase is interpretedas meaning that all requirements of the clause in question of part 1 apply, except any which areclearly inapp