EN 61248-6-1997 en Transformers and Inductors for Use in Electronic and Telecommunication Equipment Part 6 Sectional Specification for Inductors on the Basis of the Capability Appr.pdf

《EN 61248-6-1997 en Transformers and Inductors for Use in Electronic and Telecommunication Equipment Part 6 Sectional Specification for Inductors on the Basis of the Capability Appr.pdf》由会员分享，可在线阅读，更多相关《EN 61248-6-1997 en Transformers and Inductors for Use in Electronic and Telecommunication Equipment Part 6 Sectional Specification for Inductors on the Basis of the Capability Appr.pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、 STD-BSI BS EN blEY8-b-ENGL 1797 = Zb24bb9 Ob58b7L 888 m BRITISH STANDARD I - _ Tkansformers and inductors for use in electronic and telecommunication equipment Part 6. Sectional specification for inductors on the basis of the capability approval procedure * * rn The European Standard EN 612486 : 19

2、97 has the status of a British Standard ICs 29.180 NO COPYING WITHOUT ES1 PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 61248-6 : 1997 IEC 61248-6 : 1996 BS EN 61248-6 : 1997 Amd.No. National foreword Date Text affected This British Standard is the English language version of EN 612486 : 199

3、7. It is identical with IEC 612486 : 1996. The UK participation in its preparation was entrusted to Technical Committee EPL51, Iliansfonners, inductors, magnetic components and ferrite materials, which has the responsibility to: - aid enquirers to understand the text; - present to the responsible in

4、ternationalEuropean committee any enquiries on the interpretation, or proposals for change, and keep the UK interests Wormed; - monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to i

5、ts secretary. From 1 January 1997, aJ IEC publications have the number 60000 added to the old number. For instance, IEC 27-1 has been renumbered as lEC 60027-1. For a period of time during the change over from one numbering system to the other, publications may contain identifiers from both systems.

6、 Cross-references Attention is dram to the fact that CEN and CENELEC Standardc normally include an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement these international or European publications m

7、ay be found in the BSI Standards Catalogue under the section entitled Jnternational Standards Correspondence Index, or by using the Find facility of the BSI Standards Electronic Catalogue. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages

8、This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 14, an inside back cover and a back cover. This British Standard, having been prepared under the direction of the Electrotechnicai Sector Board, was published under the authority of the Standards Board and co

9、mes into effect on 15 November 1997 O BSI 1997 Amendments issued since publication ISBN O 680 28430 1 STD-BSI BS EN bL2Y8-b-ENGL 1997 D Zb24bb9 Ob58b93 b50 E EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 61 248-6 August 1997 ICs 29.1 80 Descriptors: Inductors, sectional specification, capabil

10、ity approval, preparation of the detail specification, inspection requirements, detail specification English version Transformers and inductors for use in electronic and telecommunication equipment Part 6: Sectional specification for inductors on the basis of the capability approval procedure (IEC 6

11、1 248-6:1996) Transformateurs et inductances destins aux quipements lectroniques et de tlcommunications Einrichtungen Partie 6: Spcification intermdiaire pour les inductances sur la base de Ia Transformatoren und Drosseln fr elektronische und nachrichtentechnische Teil 6: Rahmenspezifikation fr Dros

12、seln mit Befhigungsanerkennung procdure de lagrment de savoir-faire (CE1 61 248-6:1996) (IEC 61 248-61996) This European Standard was approved by CENELEC on 1997-07-01. CENELEC members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving this Europea

13、n Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (Englis

14、h, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Be

15、lgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC Eutopean Committee for Eiectrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr

16、Elektrotechnische Normung Centrai Secretariat: rue de Stassart 35, B - 1050 Brussels 1997 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61248-6:1997 E STD-BSI BS EN b124-b-ENGL 1777 m Zb24bb7 b58694 597 W Page 2 EN 61248-6 : 199

17、7 Foreword The text of the International Standard IEC 61 248-6: 1996, prepared by IEC TC 5 1, Magnetic components and ferrite materials, was submitted to the Unique Acceptance Procedure and was approved by CENELEC as EN 61 248-6 on 1997-07-01 without any modification. The following dates were fixed:

18、 - latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dopl 1 998-06-0 1 - latest date by which the national standards conflicting with the EN have to be withdrawn (daw) 1998-06-01 Annexes designated “normative“ are

19、part of the body of the standard. In this standard, annex ZA is normative. Annex ZA has been added by CENELEC. Endorsement notice The text of the International Standard IEC 61 248-6:1996 was approved by CENELEC as a European Standard without any modification. Page 3 EN 61248-6 : 1997 CONTENTS Chuse

20、Scope . Normative references . Preparation of the detail specification . 3.1 General 3.2 Ratings and characteristics . 3.3 Outline drawings and winding schematic diagram . Inspection requirements to be listed in the detail specification . 4.1 Conformance inspection 4.2 Design verification Detail spe

21、cif ication . Blank detail spechation Annex ZA (normative) Normative references to international publications with their corresponding European publications Page 4 4 5 6 6 6 7 7 7 7 8 13 * Co * Page 4 EN 61248-6 : 1997 TRANSFORMERS AND INDUCTORS FOR USE IN ELECTRONIC AND TELECOMMUNICATION EQUIPMENT

22、- Part 6: Sectional specification for inductors on the basis of the capability approval procedure 1 Scope This part of IEC 1248 specifies how to prepare detail specifications for inductors to be released under the terms of IEC 1248-1 (QC 260000) capability approval. It includes a blank detail specif

23、ication (BOS), which shows the format and indicates which tests are considered to be appropriate to this type of component, although the final selection of tests to be included in the inspection schedule is at the discretion of the specification writer. It also lists appropriate ratings and characte

24、ristics. 2 Normative references The following normative documents contain provisions, which, through reference in this text, constitute provisions of this pari of IEC 1248. At the time of publication, the editions indicated were valid. All normative documents are subject to revision, and parties to

25、agreements based on this part of IEC 1248 are encouraged to investigate the possibility of applying the most recent editions of the normative documents listed below. Members of IEC and IS0 maintain registers of currently valid International Standards. IEC Guide 102: 1989, Electronic components - Spe

26、cification structures for quality assess- ment (Qualification approval and capability approval) IEC QC O01001 : 1986, Basic rules of the IEC Quality Assessment System for Electronic Components (IECQ) Amendment 2 (1994) IEC QC 001002: 1986, Rules of procedure of the IEC Quality Assessment System for

27、Electronic Components (IECQ) Amendment 2 (1994) IEC QC 001004: Specifications list IEC QC 001005: Register of firms, products and services approved under the IECQ System, including IS0 9000 IEC 68-2: Environmental testing - Part 2: lests IEC 68-2-6: 1982, Environmental testing - Part 2: T8StS - lest

28、 Fc and guidance: Vibration (sinusoidal) IEC 68-2-20: 1979. Environmental resting - Part 2: lests - Test T: Soldering Amendment 2 (1987) STD-BSI BS EN b1248-b-ENGL 1777 Lb2qbbS Ob58b77 2Tb I Page 5 EN 61248-6 : 1997 IEC 68-2-21: 1983, Environmental testing - Part 2: Tests - Test U: Robustness of fer

29、- minations and integral mounting devices Amendment 2 (1991). Amendment 3 (1992) IEC 68-2-27: 1987, Environmental testing - Part 2: Tests - Test Ea and Guidance: Shock IEC 68-2-29: 1987, Environmental testing - Part 2: Tests - Test Eb and Guidance: Bump IEC 41 O: 1973, Sampling plans and procedures

30、for inspection by attributes IEC 1007: 1994, Transformers and inductors for use in electronic and telecornmunication equipment - Measuring methods and test procedures IEC 1248-1 : 1996, Transformers and inductors for use in electronic and telecommunication equipment - Part 1: Generic specification I

31、S0 128: 1982, Technical drawings - General principles of presentation IS0 129: 1985, Technical drawings - Dimensioning - General principles, definitions, methods of execution and special indications * m * 3 Preparation of the detall speclfication This standard is intended to be used for the preparat

32、ion of detail specifications for inductors released under the terms of the IEC 1248-1 (QC 260000) capability approval procedure. It is intended for use by the following originators: a) a customer wishing to procure inductors that are within the scope of the approved capability of his supplying compo

33、nent manufacturer, for example for detail specifi- cations (DS); b) a capability approved manufacturer of inductors wishing to prepare specifications for his own products which are within the scope of his capability approval. NOTES 1 The detail specification should take the form of the BDS shown in

34、clause 5, particularly in respect of the front page format and. in principle. in respect of the presentation of the inspection requirements. 2 Unless otherwise specified, all the tests shown in the BDC are taken from IEC 1007. Those shown lined concern operating characteristics of fundamental import

35、ance. and it is strongly recommended that these are selected by the specification writer for inclusion in the detail specification. The tests shown in plain type are listed for the convenience of the specification writer, and tests should be selected from them according to the particular application

36、 of the component. 3 The specification writer may specify tests and sampling levels different from, less than, or additional to those given in the BDS. Page 6 EN 61248-6 : 1997 3.1 General 3.1.1 these shall be fully specified in the detail specification. Where additional tests of a type not defined

37、or invoked in IEC 1007 are required, 3.1.2 by the addition of the notation “(D)“. Any tests considered as being destructive shall be so denoted in the test schedule NOTE - The use of this notation is not illustrated in the BDS. 3.1.3 Tests shall be grouped in the schedule according to the level of s

38、ampling required and, unless otherwise indicated (see 4.1 b), in the order of testing required. Where 1 O0 YO testing is not required, inspection levels and acceptable quality levels shall be selected from IEC 410. 3.1.4 The completed detail specification shall be allocated a component identity numb

39、er and issue status by the originator. NOTES 1 This number is chosen by the originator (manufacturer or customer) within his own system. It is thus not subject to any external rules or codification. 2 In the special case of a manufacturers detail specification for a standard catalogue item which the

40、 manu- facturer wishes to be listed in IEC QC 001004, the national committee will allocate an appropriate number from its register. 3.1.5 A number allocated by the component manufacturer shall be additionally included in the detail specification, comprising this specification number, his factory ide

41、ntification code letters, and a unique number within his registration system, for example OC 260500/PQR/1234. NOTE - After a detail specification has been allocated the manufacturers reference number in accordance with 3.1.5, it is to be considered a contractual part of the order. Copies of all such

42、 detail specifications are to be retained by the manufacturers chief inspector. 3.2 Ratings and characteristics 3.2.1 Ratings In the case of customer-originated detail specifications, customer and manufacturer agreement shall be obtained on the ratings to be ascribed to the component in the detail s

43、pecification. These ratings shall not exceed the scope of the manufacturers capability approval (see also 1.12 of IEC 1248-1). 3.2.2 Characteristics A customer shall prescribe in the detail specification any characteristic required for a component, 3.3 3.3.1 The detail specification shall incorporat

44、e a drawing of the inductors showing important features, such as those dimensions affecting interchangeability, restrictions on mounting, and marking requirements. Outline drawings and winding SCh8matiC diagram STD-BSI BS EN b12q-b-ENGL 1797 Lb2ilbbS Ob5b99 O77 Sll Page 7 EN 61248-6 : 1997 3.3.2 The

45、 detail specification shall incorporate a schematic diagram showing all windings, screens, taps and phasings, and giving termination identification. 4 Inspection requirements to be listed In the detall specification 4.1 Conformance inspection The detail specification shall incorporate the following

46、notes: a) sampling inspections shall be carried out in accordance with IEC 410, normal inspection; b) tests in a group may be carried out in any order, except where otherwise indicated (see 3.1.3); c) components submitted to any tests marked (D) may not be released under IEC 1248-1 capability approv

47、al (D = destructive); d) the values given for measurement limits are absolute values: measurement un- certainty is to be taken into account. 4.2 Design verification The tests to be detailed under this heading are those whicti the specification writer considers to be inappropriate to lot-by-lot relea

48、se, but appropriate to the verification of new and original designs. Accordingly, they are to be performed only when specifically so stated in the order, and the detail specification shall carry a statement to this effect. If design verification is required, the number of specimens and the requireme

49、nt that there shall be no failures shall be stated in the detail specification. NOTE - Two specimens should normally be provided, unless otherwise stated. 5 Detail specification The BDS which follows, when completed in accordance with clause 3, shall form the relevant detail specif cat ion. NOTE - The front page of the BDS has been based upon the need for a customers detail specification. Where a manufacturers detail specification is required, some changes will be necessary, but the basic format should be retained. STD*BSI BS EN bL248-b-ENGL