EN 60317-15-2004 en Specifications for particular types of winding wires Part 15 Polyesterimide enamelled round aluminium wire class 180 (Incorporates Amendment A1 2010)《特种绕组线规范 第1.pdf

《EN 60317-15-2004 en Specifications for particular types of winding wires Part 15 Polyesterimide enamelled round aluminium wire class 180 (Incorporates Amendment A1 2010)《特种绕组线规范 第1.pdf》由会员分享，可在线阅读，更多相关《EN 60317-15-2004 en Specifications for particular types of winding wires Part 15 Polyesterimide enamelled round aluminium wire class 180 (Incorporates Amendment A1 2010)《特种绕组线规范 第1.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 60317-15:2004Specifications for particular types of winding wires Part 15: Polyesterimide enamelled round aluminium wire, class 180ICS 29.060.10g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53

2、g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58+A1:2010 National forewordThis British Standard is the UK implementation of EN 60317-15:2004+A1:2010. It is identical to IEC 60317-15:2004, incorporating amendment 1:2010. It supersedes BS EN 60317-15:2004 which is withdrawn.The start

3、 and finish of text introduced or altered by amendment is indicated in the text by tags. Tags indicating changes to IEC text carry th number of the IC amendment. For example, text altered by IEC amendment 1 is indicated by !“.The UK participation in its preparation was entrusted to Technical Committ

4、ee GEL/55, Winding wires.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard can

5、not confer immunity from legal obligations.BS EN 60317-15:2004+A1:2010This British Standard was published under the authority of the Standards Policy and Strategy Committee on25 November 2004 BSI 2010Amendments/corrigenda issued since publicationDate Comments 31 May 2010 Implementation of IEC amendm

6、ent 1:2010 with CENELEC endorsement A1:2010.ISBN 978 0 580 67178 4EUROPEAN STANDARD EN 60317-15:2004+A1 NORME EUROPENNE EUROPISCHE NORM March 2010CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische N

7、ormung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2004 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60317-15:2004 E ICS 29.060.10 Supersedes EN 60317-15:1994 + A1:1998English version Specifications for particula

8、r types of winding wires Part 15: Polyesterimide enamelled round aluminium wire, class 180 (IEC 60317-15:2004) Spcifications pour types particuliers de fils de bobinage Partie 15: Fil de section circulaire en aluminium maill avec polyesterimide, classe 180 (CEI 60317-15:2004) Technische Lieferbeding

9、ungen fr bestimmte Typen von Wickeldrhten Teil 15: Runddrhte aus Aluminium, lackisoliert mit Polyesterimid, Klasse 180 (IEC 60317-15:2004) This European Standard was approved by CENELEC on 2004-09-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the c

10、onditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists i

11、n three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrote

12、chnical committees of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Forewo

13、rd The text of document 55/908/FDIS, future edition 3 of IEC 60317-15, prepared by IEC TC 55, Winding wires, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60317-15 on 2004-09-01. This European Standard supersedes EN 60317-15:1994 + A1:1998. The main changes with re

14、spect to EN 60317-15:1994 are as follows: new requirements for appearance, Subclause 3.2, added; springiness test, Clause 7, determined to be inappropriate; cut-through test, Clause 10, determined to be inappropriate; high temperature failure test, Clause 22, deleted; new pin hole test, Clause 23, a

15、dded. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2005-06-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2007-09-01 Anne

16、x ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60317-15:2004 was approved by CENELEC as a European Standard without any modification. _ Page 2Foreword to amendment A1 The text of document 55/1121/CDV, future amendment 1 to IEC 60317-15:2004, prepared

17、by IEC TC 55, Winding wire, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as amendment A1 to EN 60317-15:2004 on 2010-03-01. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and CENELEC shall not be

18、 held responsible for identifying any or all such patent rights. The following dates were fixed: latest date by which the amendment has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2010-12-01 latest date by which the national standards

19、conflicting with the amendment have to be withdrawn (dow) 2013-03-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of amendment 1:2010 to the International Standard IEC 60317-15:2004 was approved by CENELEC as an amendment to the European Standard without any modification. _ BS E

20、N 60317-15:2004+A1:2010EN 60317-15:2004+A1:2010 (E)61307-51 CEI:2400 3 CONTENTS INTRODUCTION.4 1 Scope.5 2 Normative references .5 3 Definitions and general notes on methods of test and appearance5 3.1 Definitions and general notes on methods of test 5 3.2 Appearance.6 4 Dimensions 6 5 Electrical re

21、sistance .6 6 Elongation 6 7 Springiness 6 8 Flexibility and adherence6 9 Heat shock .6 10 Cut-through 6 11 Resistance to abrasion (nominal conductor diameters up to and including 2,500 mm) 6 12 Resistance to solvents7 13 Breakdown voltage .7 14 Continuity of insulation .7 15 Temperature index .7 16

22、 Resistance to refrigerants.7 17 Solderability .8 18 Heat or solvent bonding8 19 Dielectric dissipation factor.8 20 Resistance to transformer oil 8 21 Loss of mass 8 23 Pin hole test .8 30 Packaging 8 Table 1 Rsistance to abrasion7 Page 3BS EN 60317-15:2004+A1:2010EN 60317-15:2004+A1:2010 (E)INTRODU

23、CTION This part of IEC 60317 is one of a series which deals with insulated wires used for windings in electrical equipment. The series has three groups describing 1) winding wires Test methods (IEC 60851); 2) specifications for particular types of winding wires (IEC 60317); 3) packaging of winding w

24、ires (IEC 60264). Page 4BS EN 60317-15:2004+A1:2010EN 60317-15:2004+A1:2010 (E)61307-51 CEI:2400 7 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 15: Polyesterimide enamelled round aluminium wire, class 180 1 Scope This part of IEC 60317 specifies the requirements of enamelled round alumi

25、nium winding wire of class 180 with a sole coating based on polyesterimide resin, which may be modified providing it retains the chemical identity of the original resin and meets all specified wire requirements. NOTE A modified resin is a resin that has undergone a chemical change, or contains one o

26、r more additives to enhance certain performance or application characteristics. Class 180 is a thermal class that requires a minimum temperature index of 180 and a heat shock temperature of at least 200 C. The temperature in degrees Celsius corresponding to the temperature index is not necessarily t

27、hat at which it is recommended that the wire be operated and this will depend on many factors, including the type of equipment involved. The range of nominal conductor diameters covered by this standard is as follows: grade 1: 0,400 mm up to and including 1,600 mm; grade 2: 0,400 mm up to and includ

28、ing 5,000 mm. The nominal conductor diameters are specified in Clause 4 of IEC 60317-0-3. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition

29、 of the referenced document (including any amendments) applies. 3 Definitions and general notes on methods of test and appearance 3.1 Definitions and general notes on methods of test For definitions and general notes on methods of test, see Clause 3 of IEC 60317-0-3. _ 1To be published. Page 5!IEC 6

30、0317-0-3:2008, Specifications for particular types of winding wires Part 0-3: General requirements Enamelled round aluminium wire IEC 60851-4:1996, Winding wires Test methods Part 4: Chemical properties Amendment 1 (1997) Amendment 2 (2005)“ BS EN 60317-15:2004+A1:2010EN 60317-15:2004+A1:2010 (E)613

31、07-51 CEI:2400 8 In case of inconsistencies between IEC 60317-0-3 and this standard, IEC 60317-15 shall prevail. 3.2 Appearance See Clause 3 of IEC 60317-0-3. 4 Dimensions See Clause 4 of IEC 60317-0-3. 5 Electrical resistance See Clause 5 of IEC 60317-0-3. 6 Elongation See Clause 6 of IEC 60317-0-3

32、. 7 Springiness Test inappropriate. 8 Flexibility and adherence See Clause 8 of IEC 60317-0-3. 9 Heat shock See Clause 9 of IEC 60317-0-3, where the minimum heat shock temperature shall be 200 C. 10 Cut-through Test inappropriate. 11 Resistance to abrasion (nominal conductor diameters up to and incl

33、uding 2,500 mm) The wire shall meet the requirements given in Table 1. Page 6BS EN 60317-15:2004+A1:2010EN 60317-15:2004+A1:2010 (E)61307-51 CEI:2400 9 Table 1 Rsistance to abrasion Grade 1 Grade 2 Nominal conductor diameter mm Minimum average force to failure N Minimum force to failure of each meas

34、urement N Minimum average force to failure N Minimum force to failure of each measurement N 0,400 0,450 0,500 0,560 0,630 1,95 2,10 2,25 2,40 2,55 1,65 1,75 1,90 2,05 2,20 3,15 3,40 3,60 3,85 4,15 2,65 2,85 3,05 3,25 3,50 0,710 0,800 0,900 1,000 1,120 2,75 2,95 3,15 3,40 3,70 2,35 2,50 2,70 2,90 3,1

35、0 4,45 4,75 5,10 5,45 5,80 3,75 4,05 4,30 4,60 4,90 1,250 1,400 1,600 1,800 2,000 3,95 4,25 4,60 3,35 3,60 3,90 6,25 6,65 7,15 7,70 8,20 5,25 5,45 5,85 6,50 6,95 2,240 2,500 8,75 9,30 7,40 7,90 For intermediate nominal conductor diameters, the value of the next larger nominal conductor diameter shal

36、l be taken. 12 Resistance to solvents See Clause 12 of IEC 60317-0-3. 13 Breakdown voltage See Clause 13 of IEC 60317-0-3, where the elevated temperature shall be 180 C. 14 Continuity of insulation See Clause 14 of IEC 60317-0-3. 15 Temperature index See Clause 15 of IEC 60317-0-3, where the minimum

37、 temperature index shall be 180. 16 Resistance to refrigerants Test inappropriate. Page 7BS EN 60317-15:2004+A1:2010EN 60317-15:2004+A1:2010 (E)61307-51 CEI:2400 01 17 Solderability Test inappropriate. 18 Heat or solvent bonding Test inappropriate. 19 Dielectric dissipation factor Test inappropriate

38、. 20 Resistance to transformer oil 21 Loss of mass Test inappropriate. 23 Pin hole test See Clause 23 of IEC 60317-0-3. 30 Packaging See Clause 30 of IEC 60317-0-3. _ Page 8!Test according to Clause 6 of IEC 60851-4 appropriate. Test requirements are under consideration.“ BS EN 60317-15:2004+A1:2010

39、EN 60317-15:2004+A1:2010 (E)- 3 - NE 063-7115:2004 !Annex ZA (normative) Normative references to international publications with their corresponding European publications The following referenced documents are indispensable for the application of this document. For dated references, only the edition

40、 cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Page 9Publication Year Title EN/HD Year IEC 603

41、17-0-3 2008 Specifications for particular types of winding wires - Part 0-3: General requirements - Enamelled round aluminum wire EN 60317-0-3 2008 IEC 60851-4 + A1 + A2 1996 1997 2005 Winding wires - Test methods - Part 4: Chemical properties EN 60851-4 + A1 + A2 1996 1997 2005 BS EN 60317-15:2004+

42、A1:2010EN 60317-15:2004+A1:2010 (E)“BSI GroupHeadquarters 389 Chiswick High Road, London, W4 4AL, UK Tel +44 (0)20 8996 9001 Fax +44 (0)20 8996 7001 standardsBSI - British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view

43、on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the qua

44、lity of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (

45、0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (

46、0)20 8996 9001. Fax: +44 (0)20 8996 7001 Email: You may also buy directly using a debit/credit card from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unles

47、s otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its produ

48、cts and services. Contact Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British Standards Online can be found at http:/ information about BSI is available on the BSI website at http:/ CopyrightCopyright subsists in all BS