EN 60317-0-9-2015 en Specifications for particular types of winding wires - Part 0-9 General requirements - Enamelled rectangular aluminium wire.pdf

《EN 60317-0-9-2015 en Specifications for particular types of winding wires - Part 0-9 General requirements - Enamelled rectangular aluminium wire.pdf》由会员分享，可在线阅读，更多相关《EN 60317-0-9-2015 en Specifications for particular types of winding wires - Part 0-9 General requirements - Enamelled rectangular aluminium wire.pdf（32页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards PublicationSpecifications for particular types of winding wiresPart 0-9: General requirements Enamelled rectangular aluminium wireBS EN 60317-0-9:2015National forewordThis British Standard is the UK implementation of EN 60317-0-9:2015.It is identical to IEC 60317-0-9:2015.The UK partic

2、ipation in its preparation was entrusted to TechnicalCommittee L/-/99, Miscellaneous Standards - Electrical.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users a

3、re responsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 83231 4ICS 29.060.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theS

4、tandards Policy and Strategy Committee on 31 December 2015.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 60317-0-9:2015EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60317-0-9 December 2015 ICS 29.060.10 English Version Specifications for particular type

5、s of winding wires - Part 0-9: General requirements - Enamelled rectangular aluminium wire (IEC 60317-0-9:2015) Spcifications pour types particuliers de fils de bobinage - Partie 0-9: Exigences gnrales - Fil de section rectangulaire maill en aluminium (IEC 60317-0-9:2015) Technische Lieferbedingunge

6、n fr bestimmte Typen von Wickeldrhten - Teil 0-9: Allgemeine Anforderungen - Flachdrhte aus Aluminium, lackisoliert (IEC 60317-0-9:2015) This European Standard was approved by CENELEC on 2015-06-09. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the con

7、ditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard

8、exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the

9、national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,

10、 Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17,

11、 B-1000 Brussels 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 60317-0-9:2015 E BS EN 60317-0-9:2015EN 60317-0-9:2015 (E) 2 European foreword The text of document 55/1519/FDIS, future edition 1 of IEC 60317-0-9, prepared by I

12、EC/TC 55 “Winding wires“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60317-0-9:2015. The following dates are fixed: latest date by which the document hasto be implemented at national level bypublication of an identical nationalstandard or by endorsement(dop) 2016-06-

13、04 latest date by which the nationalstandards conflicting with thedocument have to be withdrawn(dow) 2018-06-09 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any o

14、r all such patent rights. Endorsement notice The text of the International Standard IEC 60317-0-9:2015 was approved by CENELEC as a European Standard without any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 60264 serie

15、s NOTE Harmonized in EN 60264 series. IEC 60317 series NOTE Harmonized in EN 60317 series. BS EN 60317-0-9:2015EN 60317-0-9:2015 (E) 3 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part,

16、are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been mod

17、ified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 60172 2015 Test procedure for the determination

18、of the temperature index of enamelled and tape wrapped winding wires EN 60172 2015 IEC 60317-0-1 - Specifications for particular types of winding wires - Part 0-1: General requirements - Enamelled round copper wire EN 60317-0-1 - IEC 60851 series Winding wires - Test methods EN 60851 series ISO 3 -

19、Preferred numbers; Series of preferred numbers - - BS EN 60317-0-9:2015 2 IEC 60317-0-9:2015 IEC 2015 CONTENTS FOREWORD . 4 INTRODUCTION . 6 1 Scope 7 2 Normative references 7 3 Terms, definitions, general notes and appearance . 7 3.1 Terms and definitions 7 3.2 General notes . 7 3.2.1 Methods of te

20、st 7 3.2.2 Winding wire 8 3.3 Appearance 8 4 Dimensions 8 4.1 Conductor dimensions 8 4.2 Tolerance on conductor dimensions 9 4.3 Rounding of corners 9 4.4 Increase in dimensions due to the insulation . 11 4.5 Overall dimensions . 11 4.5.1 Nominal overall dimensions . 11 4.5.2 Minimum overall dimensi

21、ons 11 4.5.3 Maximum overall dimensions . 11 5 Electrical resistance 12 6 Elongation . 12 7 Springiness . 12 8 Flexibility and adherence . 12 8.1 Mandrel winding test . 12 8.2 Adherence test 12 9 Heat shock 12 10 Cut-through . 12 11 Resistance to abrasion 13 12 Resistance to solvents . 13 13 Breakdo

22、wn voltage 13 14 Continuity of insulation 13 15 Temperature index 13 16 Resistance to refrigerants 13 17 Solderability 14 18 Heat or solvent bonding . 14 19 Dielectric dissipation factor 14 20 Resistance to transformer oil . 14 21 Loss of mass . 14 23 Pin hole test 14 30 Packaging . 14 Annex A (info

23、rmative) Nominal cross-sectional areas for preferred and intermediate sizes . 15 Annex B (informative) Special tolerances . 24 BS EN 60317-0-9:2015IEC 60317-0-9:2015 IEC 2015 3 Bibliography 25 Table 1 Conductor tolerances . 9 Table 2 Nominal cross-sectional areas of preferred sizes . 10 Table 3 Corn

24、er radii . 11 Table 4 Increases in dimensions 11 Table 5 Mandrel winding 12 Table 6 Breakdown voltage 13 Table A.1 Nominal cross-sectional areas (1 of 9) . 15 Table B.1 Overall dimensional tolerances for grade 2 24 BS EN 60317-0-9:2015 4 IEC 60317-0-9:2015 IEC 2015 INTERNATIONAL ELECTROTECHNICAL COM

25、MISSION _ SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 0-9: General requirements Enamelled rectangular aluminium wire FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprisingall national electrotechnical committees (IEC N

26、ational Committees). The object of IEC is to promoteinternational co-operation on all questions concerning standardization in the electrical and electronic fields. Tothis end and in addition to other activities, IEC publishes International Standards, Technical Specifications,Technical Reports, Publi

27、cly Available Specifications (PAS) and Guides (hereafter referred to as “IECPublication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interestedin the subject dealt with may participate in this preparatory work. International, governmental and non-governmen

28、tal organizations liaising with the IEC also participate in this preparation. IEC collaborates closelywith the International Organization for Standardization (ISO) in accordance with conditions determined byagreement between the two organizations.2) The formal decisions or agreements of IEC on techn

29、ical matters express, as nearly as possible, an internationalconsensus of opinion on the relevant subjects since each technical committee has representation from allinterested IEC National Committees.3) IEC Publications have the form of recommendations for international use and are accepted by IEC N

30、ationalCommittees in that sense. While all reasonable efforts are made to ensure that the technical content of IECPublications is accurate, IEC cannot be held responsible for the way in which they are used or for anymisinterpretation by any end user.4) In order to promote international uniformity, I

31、EC National Committees undertake to apply IEC Publicationstransparently to the maximum extent possible in their national and regional publications. Any divergencebetween any IEC Publication and the corresponding national or regional publication shall be clearly indicated inthe latter.5) IEC itself d

32、oes not provide any attestation of conformity. Independent certification bodies provide conformityassessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for anyservices carried out by independent certification bodies.6) All users should ensure that they hav

33、e the latest edition of this publication.7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts andmembers of its technical committees and IEC National Committees for any personal injury, property damage orother damage of any nature whatsoeve

34、r, whether direct or indirect, or for costs (including legal fees) andexpenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IECPublications.8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications i

35、sindispensable for the correct application of this publication.9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject ofpatent rights. IEC shall not be held responsible for identifying any or all such patent rights.International Standard IEC 603

36、17-0-9 has been prepared by IEC technical committee 55: Winding wires. The text of this standard is based on the following documents: FDIS Report on voting 55/1519/FDIS 55/1525/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the

37、above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The numbering of clauses in this standard is not continuous from Clauses 21 through 30 in order to reserve space for possible future wire requirements prior to those for wire packaging. BS EN 60317-0-9:

38、2015IEC 60317-0-9:2015 IEC 2015 5 A list of all parts in the IEC 60317 series, published under the general title Specifications for particular types of winding wires, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stab

39、ility date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. BS EN 60317-0-9:2015 6 IEC 60317-0-9:2015 IEC 2015 INTRODUCTION This part o

40、f IEC 60317 is one of a series which deals with insulated wires used for windings in electrical equipment. The series has three groups describing: 1) Winding wires Test methods (IEC 60851 series);2) Specifications for particular types of winding wires (IEC 60317 series);3) Packaging of winding wires

41、 (IEC 60264 series).BS EN 60317-0-9:2015IEC 60317-0-9:2015 IEC 2015 7 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 0-9: General requirements Enamelled rectangular aluminium wire 1 Scope This part of IEC 60317 specifies the general requirements of enamelled rectangular aluminium winding

42、wires. The range of nominal conductor dimensions is given in the relevant specification sheet. When reference is made to a winding wire according to a standard of the IEC 60317 series mentioned under Clause 2, the following information is given in the description: reference to IEC specification; nom

43、inal conductor dimensions in millimetres (width thickness); grade. EXAMPLE IEC 60317-16 4,00 x 1,00 Grade 1 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the editi

44、on cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 601721, Test procedure for the determination of the temperature index of enamelled and tape wrapped winding wires IEC 60317-0-1, Specifications for particular types of wind

45、ing wires Part 0-1: General requirements Enamelled round copper wire IEC 60851 (all parts), Winding wires Test methods ISO 3, Preferred numbers Series of preferred numbers 3 Terms, definitions, general notes and appearance 3.1 Terms and definitions For the purposes of this document, the terms and de

46、finitions given in IEC 60317-0-1 apply. 3.2 General notes 3.2.1 Methods of test All methods of test to be used for this standard are given in IEC 60851. _ 1Fourth edition to be published. BS EN 60317-0-9:2015 8 IEC 60317-0-9:2015 IEC 2015 The clause numbers used in this standard are identical to the

47、 corresponding test numbers in the IEC 60851 series of standards. In case of inconsistencies between the publication on methods of test and this standard, IEC 60317-0-9 shall prevail. Where no specific range of nominal conductor dimensions is given for a test, the test applies to all nominal conduct

48、or dimensions covered by the specification sheet. Unless otherwise specified, all tests shall be carried out at a temperature from 15 C to 35 C and a relative humidity from 45 % to 75 %. Before measurements are made, the specimens shall be preconditioned under these atmospheric conditions for a time

49、 sufficient to allow the specimens to reach stability. The wire to be tested shall be removed from the packaging in such a way that the wire will not be subjected to tension or unnecessary bends. Before each test, sufficient wire should be discarded to ensure that any damaged wire is not included in the test specimens. 3.2.2 Winding wire When reference is made to a winding wire according to a standard of the IEC 60317 series mentioned under