EN 50342-3-2008 en Lead-acid starter batteries - Part 3 Terminal system for batteries with 36 V nominal voltage《铅酸起动电池组 第3部分 标称电压为36V电池引出端系统》.pdf

《EN 50342-3-2008 en Lead-acid starter batteries - Part 3 Terminal system for batteries with 36 V nominal voltage《铅酸起动电池组 第3部分 标称电压为36V电池引出端系统》.pdf》由会员分享，可在线阅读，更多相关《EN 50342-3-2008 en Lead-acid starter batteries - Part 3 Terminal system for batteries with 36 V nominal voltage《铅酸起动电池组 第3部分 标称电压为36V电池引出端系统》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、Lead-acid starter batteries Part 3: Terminal system for batteries with 36 Vnominal voltageBS EN 50342-3:2008raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI British StandardsNational forewordThis British Standard is the UK implementation of EN 5034

2、2-3:2008.The UK participation in its preparation was entrusted to Technical CommitteePEL/21, Secondary cells and batteries.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions of aco

3、ntract. Users are responsible for its correct application. BSI 2009ISBN 978 0 580 65470 1ICS 29.220.20BRITISH STANDARDBS EN 50342-3:2008Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of the StandardsPolicy and S

4、trategy Committee on Amendments issued since publicationAmd. No. Date Text affectedMarch 200931EUROPEAN STANDARD EN 50342-3 NORME EUROPENNE EUROPISCHE NORM October 2008 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee

5、 fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2008 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 50342-3:2008 E ICS 29.220.20 English version Lead-acid starter batteries - Part 3: Termi

6、nal system for batteries with 36 V nominal voltage Batteries daccumulateurs de dmarrage au plomb - Partie 3: Systme de bornes pour batteries de tension nominale de 36 VBlei-Akkumulatoren-Starterbatterien - Teil 3: Anschlusssystem fr Batterien mit 36 V Nennspannung This European Standard was approved

7、 by CENELEC on 2008-10-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national

8、 standards may be obtained on applica-tion to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other lan-guage made by translation under the responsibility of a CENELEC member into its own language

9、and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,

10、Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 50342-3:2008EN 50342-3:2008 - 2 - Foreword This European Standard was prepared by the Technical Committee CENELEC TC 21X, Secondary cells and

11、 batteries. The text of the draft was submitted to the Unique Acceptance Procedure and was approved by CENELEC as EN 50342-3 on 2008-10-01. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endor

12、sement (dop) 2009-10-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2011-10-01 _ BS EN 50342-3:2008- 3 - EN 50342-3:2008 Contents 1 Scope . 4 2 Normative references . 4 3 Definitions . 4 4 Design, dimensions and resignations 4 4.1 General 4 4.2 Syst

13、em of battery terminals . 5 Figures Figure 1 Top view of battery terminals . 5 Figure 2 Cut AA across the terminal . 6 Figure 3 Plastic cap for protection of lead taper . 8 Figure 4 Touch protection with polarity coding . 9 BS EN 50342-3:2008EN 50342-3:2008 - 4 - 1 Scope This European Standard is ap

14、plicable to lead-acid batteries used for starting, lighting and ignition of passenger automobiles and light commercial vehicles with a nominal voltage of 36 V. This standard specifies the position, details of design and dimensions of a system of battery terminals. Starter batteries with 36 V nominal

15、 voltage may have the same dimensions and means for fixation as 6 V or 12 V batteries. This can be either intentional or unintentional. Therefore, the compatibility of batteries with 36 V nominal voltage down to electric power nets with 6 V or 12 V nominal voltage should be prevented. Such design of

16、 a 36 V termination and contacting system must prevent the case to be connected to a 6 V or 12 V power net in order to avoid serious damage in the 6 V or 12 V power net. For the same reason the design of the battery terminals must prevent that standard commercial jumper-cables may be contacted to th

17、e 36 V battery terminals if the battery is installed in the vehicle or not. A commercial application of this standard must expressively be agreed upon as the final standard may differ from the present draft. 2 Normative references The following referenced documents are indispensable for the applicat

18、ion of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 50342-1 Lead-acid starter batteries Part 1: General requirements and methods of test EN 61429 Marking of secondary

19、cells and batteries with the international recycling symbol ISO 7000-1135 and indications regarding directives 93/86/EEC and 91/157/EEC (IEC 61429) EN ISO 1043 Series Plastics Symbols and abbreviated terms (ISO 1043 Series) IEC 60050-482 International Electrotechnical Vocabulary (IEV) Part 482: Prim

20、ary and secondary cells and batteries IEC 60417 Graphical symbols for use on equipment 3 Definitions For the purposes of this document, the terms and definitions of the International Electrotechnical Vocabulary (IEC 60050-482) are applicable. 4 Design, dimensions and resignations 4.1 General All mea

21、sures are indicated in millimetres. Mechanical tensions must be kept away from the bushings of the battery. A free space at the side and behind each terminal is required for electric/electronic devices. Further on the free space may provide the possibility to support the cables mechanically. The sys

22、tem of battery terminals must prevent reversed polarity in order to avoid damages in the 36 V power net. BS EN 50342-3:2008- 5 - EN 50342-3:2008 4.2 System of battery terminals 4.2.1 Position of terminals in relation to the outer contours Figure 1 shows the top view of the battery with the systems o

23、f the positive and negative battery terminals and there position to the outer contour of the battery cover. The position and dimension of the battery terminals including the free space besides the terminals are identical for the battery dimension LN3-36V through LN6-36V. As well Figure 1 shows the p

24、osition of the marking of polarity and the device for the rotatable touch-prevention. Figure 1 Top view of battery terminals BS EN 50342-3:2008EN 50342-3:2008 - 6 - 4.2.2 Cut A-A, sectional view of the system of battery terminals Figure 2 shows the cut AA across the terminals with the following deta

25、ils: - contacting sleeve; - plastic cap for protection of lead taper (Figure 3); - clips for touch protection; - touch protection (Figure 4). Figure 2 Cut AA across the terminal BS EN 50342-3:2008- 7 - EN 50342-3:2008 4.2.3 Basic terminal with contacting sleeve The basic terminal is a lead-cone (sho

26、wn single hatched) with a tinned sleeve made from brass for the electrical contact (shown double hatched). The contact may be positioned and rotated in the area of the niche walls of the terminal by an angle of more than 225. NOTE The surface of the tinned sleeve needs to be specified later. In the

27、upper section the sleeve has a groove around. This groove may be used for additional mechanical fixation of the electrical contact. The free portion of the lead-cone can be used by the battery manufacturer for the formation. This lead-cone is covered by means of a plastic cap (4.2.5) before deliveri

28、ng the battery. 4.2.4 Clips for the rotatable touch protection The battery lid surface includes six clips for touch protection centrically around each terminal. These clips have grooves at the inside to hold the rotatable touch protection. Five of these clips have also grooves at the outside (at the

29、 sixth groove this is not realizable because of manufacturing process reasons). These grooves may be used alternatively for the mechanical fixation of the electric contact if necessary. NOTE The outside groves may be cancelled, if they are not needed. 4.2.5 Plastic cap for terminal protection The ca

30、p for terminal protection according to Figure 3 prevents short circuits between the two polarities. At the same time the cap for terminal protection together with the touch protection (4.2.6) prevents to use standard jumper-cables. The plastic cap is mounted by the manufacturer and remains unchanged

31、 on the battery during the battery live. The cap clips into the upper contour of the contacting sleeve and closes flush with the sleeve. For contacting the electrical contacting clamp is pushed over the cap. 4.2.6 Rotatable touch protection The battery terminal is covered in its full height by a con

32、tinuously rotating touch protection device (Figure 4). This touch protection device is a plastic cylinder and is permanently connected to the battery cover with its clips. The slot in the cylinders is used for intrusion and positioning of the battery cables. The battery terminals and the touch prote

33、ction have the same dimensions for both polarities. In order to achieve prevention of reversed polarity the touch protection features differently positioned codes. 4.2.7 Free space behind the terminal Behind respectively at the side of the terminal the battery cover features a rectangular free space

34、 of minimum area of 50 mm x 50 mm. This free space may be used for components like electronic parts or distributors. Furthermore, the free space may be used to keep away mechanical tensions of the battery cable from the terminal bushing. 4.2.8 Marking of polarity For the marking of the polarity pola

35、rity signs are moulded into the battery cover. In addition the caps for terminal protection are marked in different colours. BS EN 50342-3:2008EN 50342-3:2008 - 8 - Figure 3 Plastic cap for protection of lead taper BS EN 50342-3:2008- 9 - EN 50342-3:2008 Figure 4 Touch protection with polarity codin

36、g BS EN 50342-3:2008This page deliberately left blankBS EN 50342-3:2008This page deliberately left blankBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter

37、.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or

38、editions.It is the constant aim of BSI to improve the quality of our products andservices. We would be grateful if anyone finding an inaccuracy orambiguity while using this British Standard would inform the Secretary ofthe technical committee responsible, the identity of which can be foundon the ins

39、ide front cover.Tel: +44 (0)20 8996 9000 Fax: +44 (0)20 8996 7400BSI offers members an individual updating service called PLUS whichensures that subscribers automatically receive the latest editions ofstandards.Buying standardsOrders for all BSI, international and foreign standards publicationsshoul

40、d be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: You may also buy directly using a debit/credit card from the BSI Shopon the website response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have bee

41、n publishedas British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library.Various BSI electronic information services are also available which givedetails on all its products and s

42、ervices. Contact the Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact MembershipA

43、dministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website CopyrightCopyright subsists in all BSI publications. BSI also holds the

44、 copyright, in the UK, of thepublications of the international standardization bodies. Except as permitted under theCopyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrievalsystem or transmitted in any form or by any means electronic, photocopying, recording orother

45、wise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard of necessarydetails such as symbols, and size, type or grade designations. If these details are to be used forany other purpose than implementation then the prior written permission of BSI must beobtained. Details and advice can be obtained from the Copyright & Licensing Manager.Tel: +44 (0)20 8996 7070 Email: WB9423_BSI_StandardColCov_noK_AW:BSI FRONT COVERS 5/9/08 12:55 Page 2