EN 15386-2007 en Packaging - Flexible laminate and plastic tubes - Test method to determine the print adhesion《包装 柔性叠层板和塑料管 测定印刷附着力的试验方法》.pdf

《EN 15386-2007 en Packaging - Flexible laminate and plastic tubes - Test method to determine the print adhesion《包装 柔性叠层板和塑料管 测定印刷附着力的试验方法》.pdf》由会员分享，可在线阅读，更多相关《EN 15386-2007 en Packaging - Flexible laminate and plastic tubes - Test method to determine the print adhesion《包装 柔性叠层板和塑料管 测定印刷附着力的试验方法》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 15386:2007Packaging Flexible laminate and plastic tubes Test method to determine the print adhesionICS 55.120g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g

2、51g60g53g44g42g43g55g3g47g36g58BS EN 15386:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 February 2008 BSI 2008ISBN 978 0 580 55648 7National forewordThis British Standard is the UK implementation of EN 15386:2007.The UK participatio

3、n in its preparation was entrusted to Technical Committee PKW/0, Packaging.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct

4、application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corrigenda issued since publicationDate CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 15386November 2007ICS 55.120English VersionPackaging - Flexible laminate and plastic tubes - Test

5、method todetermine the print adhesionEmballage - Tubes souples plastiques et tubes soupleslamins - Mthode dessai pour dterminer ladhrence delimpressionPackmittel - Laminat- und Kunststofftuben - Prfverfahrenzur Bestimmung der Haftfestigkeit der BedruckungThis European Standard was approved by CEN on

6、 30 September 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may

7、 be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN

8、Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, N

9、orway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form

10、and by any means reservedworldwide for CEN national Members.Ref. No. EN 15386:2007: EEN 15386:2007 (E) 2 Contents . page Foreword. 3 1 Scope . 4 2 Principle. 4 3 Apparatus 4 4 Procedure 4 5 Test report. 5 Annex A (normative) Peel adhesion (180 ) at 300 mm/min . 6 EN 15386:2007 (E) 3 Foreword This do

11、cument (EN 15386:2007) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2008, and con

12、flicting national standards shall be withdrawn at the latest by May 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This standar

13、d is based on the professional recommendations of the European Tube Manufacturers Association (etma). According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus,

14、Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 15386:2007 (E) 4 1 Scope This standard

15、 specifies a method for the determination of the print adhesion on flexible laminate and plastic tubes. It is applicable to flexible laminate and plastic tubes used for packing pharmaceutical, cosmetic, hygiene, food and other household products. 2 Principle The adhesive tape test serves to gauge th

16、e adhesion properties of printing ink films on flexible laminate and plastic tubes. The printing ink film is tested by rapidly tearing-off a previously applied adhesive tape. After the tape has been torn off, the divided surfaces are judged by pre-established criteria. 3 Apparatus An adhesive tape o

17、f commercial quality equipped with an upper surface made of tear-proof plastic and a pressure sensitive adhesive coating, of which the adhesive power is: minimum 5 N/25 mm and maximum 7 N/25 mm, tested according to Annex A against a glass testing surface. 4 Procedure Place the printed sample on an e

18、ven surface. Apply the adhesive tape on the sample and press it on manually across the length of the decoration. It is important that there is full contact with the surface over the whole area and that no air bubbles remain between adhesive tape and sample surface. Approximately 10 s to 30 s after p

19、ressing-on, manually tear off the free end of the adhesive tape in one go from the surface at an angle of about 150 . Examine the divided surfaces (printing surface and reverse side of the adhesive tape). Analyse the divided surfaces according to Table 1. Table 1 Evaluation of test results Appearanc

20、e of the divided surfaces Assessment Category No damage of the print or the printing material, pure adhesion fracture Adhesive tape resistant Pass Damage to the print and printing material. Not adhesive tape resistant Fail The severity of the failure mode should be defined between customer and suppl

21、ier. EN 15386:2007 (E) 5 5 Test report If not otherwise agreed between supplier and customer the test report shall contain the following information: a) Reference to this standard and if necessary a specification for the method of sampling and acceptance of the batch, b) Complete identification of t

22、he batch and of the tubes checked, c) Date of printing, d) Number of tubes checked, e) Number of defects, f) Test result, g) All factors which could have affected the results or all operating details not specified in this standard, h) Date, place of test and name of tester. EN 15386:2007 (E) 6 Annex

23、 A (normative) Peel adhesion (180 ) at 300 mm/min A.1 Scope This test method is designed to quantify the permanence of adhesion or peel ability of self-adhesive, pressure sensitive materials A.2 Definition Peel adhesion is defined as the force required to remove pressure sensitive coated material, w

24、hich has been applied to a standard test plate under specified conditions from the plate at a specified angle and speed. Adhesion is measured at 20 min after the application and 24 h after application, the latter being considered as the ultimate adhesion. A.3 Apparatus and reagents A tensile tester

25、or similar machine, capable of peeling a laminate through an angle of 180 with a jaw separation rate of 300 mm/min with an accuracy of 2 %. Test plates made of float glass or similar plate glass. A 2 kg roller. NOTE 1 The standard FINAT test roller is recommended for this purpose1. The test plates s

26、hall be thoroughly cleaned so that no trace of adhesive, grease, silicone or moisture is left on the surface. The following solvents can be used to clean the test plates: Diacetone alcohol non-residual, technical grade or better Methyl Ethyl Ketone (MEK) Acetone Methanol 95 % n-Heptane Ethyl Acetate

27、 1Information on how to obtain a FINAT hand roller is available from FINAT,Laan Copes van Cattenburch 79, 2585 EW The Hague, Netherlands, e-mail: URL: 1. The FINAT test roller is an example of a suitable product available commercially. This information is given for the convenience of users of this

28、European Standard and does not constitute an endorsement by CEN of this product. EN 15386:2007 (E) 7 The cleaning material shall be absorbent, e.g. surgical gauze, cotton wool or tissue. To be suitable, materials shall be lint-free during use, absorbent, contain no additives that are soluble in the

29、solvents listed above, and made exclusively from virgin materials. Dispense one of the solvents listed above onto the panel, wiping it to dryness with fresh absorbent cleaning material. Repeat for a total of three washes with the solvent. Final wipe shall be with MEK or acetone. Alternative methods

30、that remove contamination properly can be adopted, e.g. ultrasonic cleaning. Prior to use, the cleaned plates should be left for 4 hours under standard test conditions. Care should be taken to handle clean plates by the edge only. Alternative surfaces to plate glass can be used such as stainless ste

31、el aluminium or polyester film, but this must be clearly stated alongside the results. If adhesion values are required when paper tear has occurred, then this test can be conducted at lower jaw separation rates quoting the latter against the results. NOTE 2 Conversion 1 Kgf = 9,81 N. A.4 Test Pieces

32、 These should be strips taken from a representative sample of material. The strips should be 25 mm wide and have a minimum length of 175 mm in the machine direction. The cuts should be clean and straight. At least three strips should be taken from each material sample. A.5 Conditioning Temperature 2

33、3 C 2 C, 50 % RH 5% RH. The test sample or test strips should be conditioned for not less than 4 h before testing. Figure A.1 Test strips A.6 Procedure Remove the backing material from each strip and place the adhesive coated facing material, adhesive side down, on to a clean test plate using light

34、finger pressure. Roll twice in each direction with the roller at a speed of approximately 10 mm/s to obtain intimate contact between the adhesive mass and the surface. After applying the strips to the test plate, leave for a period of 20 min before testing. Repeat the procedure with a second set of

35、strips and leave for a period of 24 h before testing. Fix the test plate and strip in the machine so that the angle of peel is 180 . Set the machine at 300 mm/min jaw separation rate. Carry out the test taking at least five readings at 10 mm intervals from the centre section of each test strip. Aver

36、age the five or more readings for each strip. EN 15386:2007 (E) 8 A.7 Results Peel adhesion (180 ) is expressed as the average result for the strips tested in Newtons per 25 mm width for either 20 min or 24 h application time. A.8 Failure Description Code CP Clear Panel - no visible stain on panel.

37、PS Panel Stain - discoloration of test area, but no tacky residue. CF Cohesive Failure - the adhesive film is split during the test, leaving residue of adhesive on both the panel and the front material. AT Adhesive Transfer - the adhesive separates cleanly from the front material, leaving adhesive f

38、ilm on the test panel. The approximate extent of transfer should be quoted as a percentage. PT Paper Tear - the adhesive force exceeds the strength of a paper facing material. The results quoted should be the maximum reached before the paper tears. EN 15386:2007 (E) 9 Bibliography 1 FINAT Technical

39、Handbook Section 2: Test Equipment 2.1 Standard FINAT Test Roller (FINAT website : http:/)12 EN 12374, Packaging Flexible tubes - Terminology 3 EN 13045, Packaging Flexible cylindrical plastic tubes Dimensions and tolerances 4 EN 13461, Packaging Cylindrical flexible laminated tubes Dimensions and t

40、olerances BS EN 15386:2007BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.Revisio

41、nsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambigui

42、ty while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that su

43、bscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the

44、 BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europea

45、n and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email

46、: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membership

47、bsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publi

48、cations of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written perm

49、ission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: