EN 586-1-1997 en Aluminium and Aluminium Alloys - Forgings - Part 1 Technical Conditions for Inspection and Delivery《铝和铝合金 锻件 第1部分 交货技术要求》.pdf

《EN 586-1-1997 en Aluminium and Aluminium Alloys - Forgings - Part 1 Technical Conditions for Inspection and Delivery《铝和铝合金 锻件 第1部分 交货技术要求》.pdf》由会员分享，可在线阅读，更多相关《EN 586-1-1997 en Aluminium and Aluminium Alloys - Forgings - Part 1 Technical Conditions for Inspection and Delivery《铝和铝合金 锻件 第1部分 交货技术要求》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、STD-BSI BS EN 58b-1-ENGL 1798 D Lb24bb Ob78132 531 = BRITISH STANDARD BS EN 586-1 : 1998 Aluminium and aluminium alloys - Forgings Part 1. Technical conditions for inspection and delivery The European Standard EN 5861 : 1997 has the status of a British Standard ICs 77.150.10 u- NO COPYING WITHOUT BS

2、I PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW STD-BSI BS EN SBb-L-ENGL 1998 D lb2Libb9 Ob78133 Li78 9 Amd No. BS EN 686-1 : 1998 Date Rxtaffectd This British Stanard, having been prepared under the direction of the Sector Board for Engineering, was published under the authority of the Standarcis

3、 Board and comes into effect on 16 February 1998 Q BSI 1998 ISBN O 680 28697 6 National foreword This British Standard is the English language version of EN 586-1 : 1997, The UK participation in its preparation was entrusted to khnicd Committee NFE/35/5, Wrought aluminium and duminium aiioys, which

4、has the responsibility to: - aid enquirem to understand the text; - present to the responsible European committee any enquiries on the interpretation, or propads for change, and keep the UK interests informed; - monitor related international and European developments and promulgate them in the UK A

5、list of organizaions represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled Internatio

6、nai standards Correspondence Index, or by using the Compliance with a British Standard does not of itself confer immunity from legal obligations. facility of the BSI Standards Ele b) the type and temper condition of the material: - the designation of the duminium and aluminium - the temper condition

7、 for delivery in accordance with EN 515 (as-forged or heat treated) and, if different, the temper condition for use; c) the number of this European Standard; d) the dimensions and shape of the product (thickness, width, length, diameter) andor reference to a drawing defining the product; e) quantity

8、, and, where applicable, quanti tolerances (see 6.7); f) any requirements for inspection documents; g) any special requirements agreed between purchaser and supplier. auoy; 5 Requirements 6.1 Production and manufacturing processes The production and manufacturing processes shall be left to the discr

9、etion of the producer. Unless it is explicitly stated otherwise in the order, no obligation shall be placed on the producer to use the same processes for subsequent and similar orders. 6.2 Quality control The supplier shall be responsible for the perormance of all inspection and tests required by th

10、e relevant European Standard or specification, prior to shipment of the product. If the purchaser wishes to inspect the product at the suppliers works, he shall notify the supplier at the time of placing the order. 6.3 Chemical composition The chemical composition shall comply with the requirements

11、given in EN 573-3. If the purchaser requires content limits for elements not specified in the above standard, these limits sha be stated on the order, after agreement between purchaser and supplier. O BSI 1998 STD=BSI BS EN 58b-L-ENGL 1778 1b24bb7 Ob78137 013 W Page 4 EN 66-1: 1997 6.4 Mechanical pr

12、operties The mechanical properties shall comply with those given in EN S2. 6.6 Surface finish Unless otherwise agreed at the time of ordering, forgings shall be cleaned by pickling in an aqueous solution of NaOH prior to surface inspection. The product shall be free from defects detrimental to its u

13、se. Whilst an operation designed to mask a defect shaU not be permitted, the elimination of a superficial surface defect shall be permissible, provided that the dimensional tolerances continue to be observed. 6.6 Tolerances on dimensions and form Tolerances on dimensions and form shall comply with p

14、rEN 586-3. NCYE. The purchaser can only reject those products having dimensions not complying with the specified tolerances 6.7 Quantity tolerance The quantity tolerance shall be f 10 W unless otherwise agreed between purchaser and supplier. 6.8 Internal quality The forgings shail be free from inkrn

15、ai defects which may be detrimental to their use. If special inspections or tests are required, these shal be agreed between purchaser and supplier. 6.9 Special properties Additionai property requirements in respect of harness and electrid conductivity tests shall be met in accordance with EN B2 whe

16、n agreed between purchaser and supplier. 6 %st method 6.1 Sampling 6.1.1 Specimens for chernicd and.s The specimens for chemical analysis shall be taken at the time of castin b) a prolongation of the forging taken to represent the inspection lot; c) an actuai forging taken from the inspection lot O

17、BSI 1998 STDDBSI BS EN 58b-L-ENGL 1778 W Lb2qbbS Ob78138 T5T 6.1.3.2 Type and location Where section thicknesses permit, a round or flat test piece shall be prepared. The longitudinal axis of the test piece shall be located at mid-section thickness. 6.1.3.3 Identif trtwn of test piecas Each test pie

18、ce shall be marked in such a manner that it is possible to identify the inspection lot from which it was taken, and, if required, its location and orientation in the product. If a test piece is marked by stamping, this shail not be in a place or manner which may interfere with subsequent testing. Wh

19、ere it is not convenient to mark a test piece, an identification tag may be attached. 6.1.3.4 Machining Any machining necessary shall be ded out in such a manner that it does not change the characteristics of the metal in the test piece. 6.1.3.6 Number of test pieces One test piece shall be taken fr

20、om each specimen unless otherwise specified 6.2 Test procedure 6.2.1 Chemical composition Methods of analysis shall be at the discretion of the supplier. In case of dispute concerning the chemical composition, reference anaipis shall be carried out by the methods specified in the relevant European S

21、tandards and the results obtained by these methods shd be accepted. If the check analysis is to be made on the processed product, a sample of the product shall be dissolved and a wet analysis carried out. 6.2.2 Mechanical and phgsical tests Tensile testing shall be carried out in accordance with EN

22、10002-1. if other mechanical or physical tests are required, these shall be agreed between purchaser and supplier. These tests shall be carried out either in accordance with relevant European Standards or by methods agreed between purchaser and supplier. 6.2.3 Measurement of dimensions The dimension

23、s shall be measured by means of measuring instruments which are of the accuracy required by the dimensions and dimensional tolerances. All dimensions shall be checked at the ambient temperature of the workshop or laboratory, and, in case of dispute, at a temperature between 15 “C and 25 “C inclusive

24、. 6.2.4 Sutface finish Examination of surface appearance shall be carried out without the assistance of magniSring apparatus on products before delivery. Page 5 EN 586-1 : 1997 6.3 Retests 6.3.1 Mechanical properties If any of the test pieces first selected fails to meet the requirements for the mec

25、hanical tests, the following procedures shal be applied: - if an error is clearly identified, either in the test piece preparation or in the test procedure, then the corresponding resuit shall be disregarded and the testing resumed as initially requird, - if this is not the case, then two further sp

26、ecimens shall be taken from the same inspection lot, one being from the me unit of product (hand forging, die forging, etc.) from which the original specimen was taken, unless that unit of product has been withdrawn by the supplier. If both test pieces from these additional specimens meet the requir

27、ements, the inspection lot which they represent shall be deemed to comply with the requirements of this European Standard. Should one test piece fail, the inspection lot sha be deemed not to comply with the requirements of this European Standard At the discretion of the supplier, the inspection lot

28、may be submitted to additional thermal treatment(s) and then retested as a new inspection lot. 6.3.2 Other properties The retests of other properties shall be agreed upon between purchaser and supplier. 7 Inspection documents 7.1 General If requested by the purchaser on the order, the supplier shall

29、 provide one of more of the following documents as applicable. These inspection documents are based on EN 10204 with modifications due to the specific needs of aluminium and aluminium alloys. The requirements of 3.1.h 3.1.B, 3.1.C are in The requirements of 7.2, 7.2.1,7.2.2 are specific to aluminium

30、 products. 7.2 Documents established on the basis of inspections and tests performed by qualified personnel who are involved in the manufacturing process andor belong to the quality control department 7.2.1 Certificate of collformity Documents by which the producer certifies that according to inspec

31、tions and results of representative tests the products for delivery comply with the relevant standards and with the additional requirements in the order, if any conformity with EN 10204. O ES1 1998 STD-BSI BS EN SBb-L-ENGL 1978 LbZibb7 Ob78137 77b W Page 6 EN586-1:1997 7.2.2 %t report Document by wh

32、ich the producer certifies that the products for delivery comply with the requirements specified on the order. This document details the results of the current production controls carried out on identical products made using the same method as the products for delivery but not necessarily on the pro

33、ducts for delivery themseives. 7.3 Documents established on the basis of inspections and tests performed or supervised by qualified personnel organizationally independent from the manufacturing department, according to the requirements specified on the order and carried out on the products for deliv

34、ery or on the relevant inspection lot Inspection certificates in accordance with EN 10204: - 3.1.A: certincate issued and vaiidated by an inspector designated by the official regulations, in accordance with these and the corresponding technicai rules; - 3.1.B certificate issued by the department ind

35、ependent of the manufachring department and validated by an authorized represenwe of the producer independent of the manufacturing departmen$ - 3.1.C. certicate issued and validated by an authorized representative of the purchaser, in accordance with the specifications of the order. 8Marking Marking

36、 of products shall be undertaken only when agreed upon between purchaser and supplier and stated on the order or drawing. This marking shali not adversely Hect the finai use of the product. 9 Packaging Unless otherwise specified in European Standards reiating to specia products or specified in the o

37、rder, the mode of packaging shall be determined by the supplier who shall take ali suitable precautions to ensure that, under the usuai conditions of transportation, the products will be delivered in a condition suitable for use. 10 Arbitration In cases of dispute concerning conformity with the requ

38、irements of this standard or specification cited on the order, before rejecting the products, testing shall be carried out by an arbitrator chosen by mutual agreement between purchaser and supplier. The arbilmhrs decision shall be finai. B BSI 1998 BS EN 586-1 : 1998 BSI 389 Chiswick High Road Londo

39、n w4 4AL BSI - British Standards Institution IS1 is the independent national body responsible for preparing British Standards. It resents the UK view on standards in Europe and at the internationai level. It is ncorporated by Royal Charter. :ontract requirements i British Standard does not purport t

40、o include ali the necessary provisions of a :ontract Users of British Standards are responsible for their correct application. levisions 3ritish Standards are updated by amendment or revision. Users of British Standards ihould make sure that they possess the latest amendments or editions. t is the c

41、onstant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this 3ritish Standard would dorm the Secretary of the responsible technical committee, he identity of which can be found on the inside front cover. Te

42、l 0181 996 9000; Fax: I181 996 7400. 3SI offers members an individual updating service called PLUS which ensures that mbscribers automatically receive the latest editions of standards. Buying standards 3rders for all BSI, international and foreign standards publications should be tddressed to Custom

43、er Services, Sales Department at Chiswick Tek 0181 996 7000, Fax: 0181 996 7001. in response to orders for international standards, it is BSI policy to supply the BSI mplementation of those that have been published as British Standards, unless Dthenvise requested. information on standards BSI provid

44、es a wide range of information on national, European and international standards through its Library, the Standardline Database, the BSI Information echnology Service (BITS) and its Technical Help to Exporters Service. Contact the information Department at Ckiswick Tek 0181 996 7111; Fax. 0181 996 7

45、048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Customer Services, Membership at Chiswick Tel 0181 996 7002; Fax: 0181 996 7001. Copyright Copyright s

46、ubsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standarmon bodies. Except as permitted under the Copynght, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any m

47、eans - electronic, photocopying, recording or otherwise - without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager, BSI, 389 Chiswick High Road, London W4 4AL.