EN 3757-2009 en Aerospace series - Nuts anchor self-locking floating selfaligning two lugs in heat resisting steel MoS2 lubricated - Classification 900 MPa (at ambient temperature).pdf

《EN 3757-2009 en Aerospace series - Nuts anchor self-locking floating selfaligning two lugs in heat resisting steel MoS2 lubricated - Classification 900 MPa (at ambient temperature).pdf》由会员分享，可在线阅读，更多相关《EN 3757-2009 en Aerospace series - Nuts anchor self-locking floating selfaligning two lugs in heat resisting steel MoS2 lubricated - Classification 900 MPa (at ambient temperature).pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BS EN 3757:2009ICS 49.030.30NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAerospace series Nuts, anchor, self-locking, floating, self-aligning, two lugs, inheat resisting steel,MoS2 lubricated Classification: 900MPa (at ambienttemperature) / 315 CThis British

2、Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 30 June2010 BSI 2010ISBN 978 0 580 68570 5Amendments/corrigenda issued since publicationDate CommentsBS EN 3757:2009National forewordThis British Standard is the UK implementation of EN 3757:2009.The UK particip

3、ation in its preparation was entrusted to TechnicalCommittee ACE/12, Aerospace fasteners and fastening systems.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. User

4、s are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.BS EN 3757:2009EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3757 November 2009 ICS 49.030.30 English Version Aerospace series - Nuts, anchor, self-locking, floating,

5、self-aligning, two lugs, in heat resisting steel, MoS2 lubricated - Classification: 900 MPa (at ambient temperature) / 315 C Srie arospatiale - crous river, freinage interne, flottants, orientables, double patte, acier rsistant chaud, lubrifis MoS2 - Classification : 900 MPa ( temprature ambiante) /

6、 315 C Luft- und Raumfahrt - Annietmuttern, selbstsichernd, schwenkbar, beiderseitiger Flansch, aus hochwarmfestem Stahl, MoS2-geschmiert - Klasse: 900 MPa (bei Raumtemperatur) / 315 C This European Standard was approved by CEN on 17 October 2009. CEN members are bound to comply with the CEN/CENELEC

7、 Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CE

8、N member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN

9、 members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Swe

10、den, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members.

11、 Ref. No. EN 3757:2009: EBS EN 3757:2009EN 3757:2009 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Required characteristics .5 4 Designation 7 5 Marking .7 6 Technical specification .7 BS EN 3757:2009EN 3757:2009 (E) 3 Foreword This document (EN 3757:2009) has been prepared by

12、the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of A

13、SD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2010, and conflicting national standards shall be withdrawn at the latest by May 2010. Attention is drawn

14、to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following

15、countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,

16、 Spain, Sweden, Switzerland and the United Kingdom. BS EN 3757:2009EN 3757:2009 (E) 4 1 Scope This European Standard specifies the characteristics of self-locking, floating, self-aligning, two lugs anchor nuts, in heat resisting steel, MoS2-lubricated. Classification: 900 MPa 1) / 315 C 2). 2 Normat

17、ive references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2424:2008, Aerospace series Mar

18、king of aerospace products EN 2491, Aerospace series Molybdenum disulphide dry lubricants Coating methods EN 9100, Quality Management Systems Requirements for Aviation, Space and Defense Organizations EN 9133, Aerospace series Quality management systems Qualification procedure for aerospace standard

19、 parts ISO 5855-2, Aerospace MJ threads Part 2: Limit dimensions for bolts and nuts ISO 5858, Aerospace Nuts, self-locking, with maximum operating temperature less than or equal to 425 C Procurement specification ISO 8788, Aerospace Nuts, metric Tolerances of form and position ISO 12273, Aerospace N

20、uts, anchor, self-locking, floating, self-aligning, two lug, with MJ threads, classifications: 900 MPa (at ambient temperature)/235 C, 900 MPa (at ambient temperature)/315 C and 900 MPa (at ambient temperature)/425 C Dimensions TR 3791, Aerospace series Materials for self-locking nuts, threaded inse

21、rts and screw thread inserts of temperature classes 425 C 3)1) Corresponds to the minimum tensile stress which the nut is able to withstand at ambient temperature without breaking or cracking when tested with a bolt of a higher strength class. 2) Maximum temperature that the nut is able to withstand

22、, without permanent alteration to its original characteristics, after ambient temperature has been restored. The maximum temperature is conditioned by the surface treatment. 3) Published as ASD-STAN Technical Report at the date of publication of this standard. BS EN 3757:2009EN 3757:2009 (E) 5 3 Req

23、uired characteristics 3.1 Configuration Dimensions Masses See Figure 1 and Table 1. Dimensions and tolerances are in conformity with ISO 12273, expressed in millimetres and apply before MoS2lubrication. Details of form not stated are at the manufacturers option. 3.2 Tolerances of form and position I

24、SO 8788. 3.3 Materials TR 3791. 3.4 Surface treatment EN 2491, thickness not specified, mandatory on threads, optional on other surfaces. These values in micrometres apply before surface treatment. They do not apply tothreads punched holes or sheared edges, the surface texture of which will be as ac

25、hieved by usual manufacturing methods. Remove sharp edges 0,1 to 0,4. 6,3 3,2 BS EN 3757:2009EN 3757:2009 (E) 6 Key 1 Marking 2 Float inclusive 3 Convex washer 4 Threaded element 5 Thread 6 Form out-of-round in this area to achieve the self-locking torque requirements. Tooling marks are permitted in

26、 this area. 7 Cage a 8 minimum alignment in any direction from central position Figure 1 BS EN 3757:2009EN 3757:2009 (E) 7 Table 1 Diameter code Thread aE F H K L M NbP R S T Z Massc+ 0,2 0 Radial float min. max. max. max. max. min. max. min. 050 MJ50,8-4H6H 8,75 17,5 3,5 15,2 23,7 8,3 0,9 6,63 2,5

27、7,2 0,7 2,6 060 MJ61-4H5H 12,7 25,4 4 17 31,6 10,21,1 7,6 7,8 0,75 5,8 080 MJ81-4H5H 5 20,5 32,6 11,8 11 3,5 3 8,4 9 aIn accordance with ISO 5855-2. In the self-locking zone, the tolerances apply before forming out-of-round. bMeasured at the rivet hole location. cApproximate values (kg/1 000 pieces)

28、, given for information purposes only. 4 Designation EXAMPLE Description block NUT Identity block EN3757060 Number of this standard Diameter code (see Table 1) NOTE If necessary the originator code I9005 shall be placed between the description block and the identity block. 5 Marking EN 2424:2008, st

29、yle N. See Figure 1. 6 Technical specification ISO 5858, except for: Approval of manufacturers: see EN 9100; Qualification of products: see EN 9133. BS EN3757:2009BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionB

30、SI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sur

31、e that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible,

32、the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, inter

33、national and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy t

34、o supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various B

35、SI electronic information services are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on

36、 the purchase price of standards. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is ava

37、ilable on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored i

38、n a retrieval system or transmitted in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email: