EN 2591-416-2001 en Aerospace Series - Elements of Electrical and Optical Connection - Test Methods - Part 416 Contact Bending Strength《航空航天系列 光电连接元件的试验方法 第416部分 接点弯曲强度》.pdf

《EN 2591-416-2001 en Aerospace Series - Elements of Electrical and Optical Connection - Test Methods - Part 416 Contact Bending Strength《航空航天系列 光电连接元件的试验方法 第416部分 接点弯曲强度》.pdf》由会员分享，可在线阅读，更多相关《EN 2591-416-2001 en Aerospace Series - Elements of Electrical and Optical Connection - Test Methods - Part 416 Contact Bending Strength《航空航天系列 光电连接元件的试验方法 第416部分 接点弯曲强度》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AEROSPACE SERIES Elements of electrical and optical connection Test methods Part 4 16: Contact bending strength The European Standard EN 2591-416:2001 has the status ofa British Standard ICs 49.060 BS EN 2591 -41 612001 Wk present to the responsible international/European committee

2、any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. - A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cr oss-r e

3、fer enc e s The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic

4、 Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This documen

5、t comprises a front cover, an inside front cover, the EN title page, pages 2 to 4, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. O BSI 12 December 2001 ISBN O 580 38109 9 EUROPEAN STANDARD NORME EUROPENNE EUROPIS

6、CHE NORM EN 2591-416 November 2001 ICs 49.060 English version Aerospace series - Elements of electrical and optical connection - Test methods - Part 416: Contact bending strength Srie arospatiale - Organes de connexion lectrique et optique - Mthodes dessais - Partie 416: Rsistance du contact la flex

7、ion Luft- und Raumfahrt - Elektrische und optische Verbindungselemente - Prfverfahren - Teil 416: Biegefestigkeit der Kontakte This European Standard was approved by CEN on 4 June 2001 CEN members are bound to comply with the CENKENELEC Internal Regulations which stipulate the conditions for giving

8、this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (

9、English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Re

10、public, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION EUROPISCHES KOMITEE FR NORMUNG COMIT EUROPEN DE NORMALISATION Management Centre: rue de Stassar

11、t, 36 B-1050 Brussels O 2001 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2591-416:2001 E EN 2591-416:2001 (E) Foreword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA) . Af

12、ter inquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of

13、 a national standard, either by publication of an identical text or by endorsement, at the latest by May 2002, and conflicting national standards shall be withdrawn at the latest by May 2002. According to the CENKENELEC Internal Regulations, the national standards organizations of the following coun

14、tries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. 2 EN 2591-416:2001 (E) 1 Scope This standard specif

15、ies a method of determining the bending strength of male contacts used in elements of electrical and optical connection. It shall be used together with EN 2591-100. NOTE This test applies only to male contacts of nominal diameter I 1 mm. 2 Normative references This European Standard incorporates by

16、dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standar

17、d only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 2591-100 Aerospace series - Elements of electrical and optical connection - Test methods - Part 100: General 1) 3 Preparation of specimens 3.1 Specimens shall

18、 not be wired and shall not have been subjected to any deformation 3.2 Unless specified in the technical specification, the following details shall be stated: - bending moment; - requirement. 4 Apparatus The specimens shall be held in a suitable fixture, see figure 1. 1 0,8 L Key 1 Permanent set 2 P

19、oint of direction of application of force Figure 1 - Example of test fixture 1) Published as AECMA Prestandard at the date of publication of this standard 3 EN 2591-416:2001 (E) 5 Method 5.1 10 of each size Number of contacts to be tested 5.2 Procedure A load corresponding to the specified bending m

20、oment shall be applied to point Pat a speed of 25 mm/min. The load indicating in the product standard shall be maintained for 1 min and then released. The contact permanent set shall be measured at 0,8 i (see figure 1). 5.3 The permanent set of the contact shall not exceed 0,13 mm Req u i remen t 4

21、BS EN 2591-41612001 BSI 389 Chiswick High Road Lon don w4 4AL BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Re vi si ons British Standards are updat

22、ed by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British

23、Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically rec

24、eive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: orders&-. Standards are also available from the BSI website at http:/www.b

25、si-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international stan

26、dards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 71 11. Fax: +44 (0)20 8996 7048. Email: infomi-. Subscribing

27、members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details ofthese and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 700 1. Email: membershipbsi-. Information regar

28、ding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, ofthe publications of th

29、e international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise -without prior written permission fro

30、m BSI. This does not preclude the free use, in the course of implementing the standard, ofnecessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then the prior written permission ofBSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyright&-.