EN 2591-207-1996 en Aerospace Series - Elements of Electrical and Optical Connection - Test Methods - Part 207 Voltage Proof Test《航空和航天系列 光电连接元件的试验方法 第207部分 电压校验》.pdf

《EN 2591-207-1996 en Aerospace Series - Elements of Electrical and Optical Connection - Test Methods - Part 207 Voltage Proof Test《航空和航天系列 光电连接元件的试验方法 第207部分 电压校验》.pdf》由会员分享，可在线阅读，更多相关《EN 2591-207-1996 en Aerospace Series - Elements of Electrical and Optical Connection - Test Methods - Part 207 Voltage Proof Test《航空和航天系列 光电连接元件的试验方法 第207部分 电压校验》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD AEROSPACE SERIES BS EN 2591-207:1996 Elements of electrical and optical connection Test methods Part 207: Voltage proof test The European Standard EN2591-207:1996 has the status of a British Standard ICS 49.060BSEN2591-207:1996 This British Standard, having been prepared under the d

2、irectionof the Engineering SectorBoard, was published underthe authority of the Standards Board and comes intoeffect on 15 June 1996 BSI 11-1999 The following BSI references relate to the work on this standard: Committee reference ACE/6 Draft for comment 92/84573 DC ISBN 0 580 25957 9 Committees res

3、ponsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee ACE/6, Aerospace avionic, electrical and fibre-optic technology, upon which the following bodies were represented: British Airways British Cable Makers Confederation British Rubber Manufa

4、cturers Association Civil Aviation Authority (Airworthiness Division) Federation of the Electronics Industry Ministry of Defence Society of British Aerospace Companies Amendments issued since publication Amd. No. Date CommentsBSEN2591-207:1996 BSI 11-1999 i Contents Page Committees responsible Insid

5、e front cover National foreword ii Foreword 2 1 Scope 3 2 Normative references 3 3 Preparation of specimens 3 4 Methods 3 List of references Inside back coverBSEN2591-207:1996 ii BSI 11-1999 National foreword This British Standard has been prepared by Technical Committee ACE/6 and is the English lan

6、guage version of EN2591-207:1996 Aerospace series Elements of electrical and optical connection Test methods Part207: Voltage proof test, published by the European Committee for Standardization (CEN). It supersedes BSEN2591-B7:1994 which is withdrawn. BS EN 2591-207:1996 was produced as a result of

7、international discussions in which the UnitedKingdom took an active part. Cross-references The British Standard corresponding to the European Standard referred to in the text is identical in number and title with that given in clause2. A British Standard does not purport to include all the necessary

8、 provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, the EN title

9、 page, pages2 to4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN2591-207 February 1996 I

10、CS49.060 Supersedes EN 2591-B7:1993 Descriptors: Aircraft industry, aircraft equipment, connecting equipment, electrical insulating materials, tests, withstand voltage, verification English version Aerospace series Elements of electrical and optical connection Test methods Part 207: Voltage proof te

11、st Srie arospatiale Organes de connexion lectrique et optique Mthodes dessais Partie 207: Essai de tenue en tension Luft- und Raumfahrt Elektrische und optische Verbindungselemente Prfverfahren Teil 207: Prfung der Spannungsfestigkeit This European Standard was approved by CEN on 1993-12-16. CEN mem

12、bers are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on applicat

13、ion to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the

14、same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom. CEN European Committee for Standardiza

15、tion Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1996 Copyright reserved to CEN members Ref. No. EN 2591-207:1996 EEN2591-207:1996 BSI 11-1999 2 Foreword This European Standard has been prepared by the European Association of

16、 Aerospace Manufacturers (AECMA). The alphanumerical designation of the Parts of EN2591 has been abandoned for a numerical designation in line with the Internal Regulations of CEN/CENELEC. This European Standard is the integral reproduction of the EuropeanStandard EN2591-B7 after application of this

17、 decision, without any other modification than the change in numbering. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August1996, and conflicting national standards shall be withdrawn at the lat

18、est by August1996. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway,

19、Portugal, Spain, Sweden, Switzerland and UnitedKingdom.EN2591-207:1996 BSI 11-1999 3 1 Scope This standard specifies the methods for the voltage proof test on the insulators of mated or unmated elements of connection. It shall be used together with EN2591. 2 Normative references This European Standa

20、rd incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to th

21、is European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 2591, Aerospace series Elements of electrical and optical connection Test methods General. 3 Preparation of specimens 3.1 The specimens sha

22、ll be wired as specified in the technical specification. Tests shall be carried out on elements of connection which are mated or unmated in accordance with the technical specification. Unless otherwise specified in the test concerned, the specimens shall not be cleaned. 3.2 Unless indicated in the t

23、echnical specification, the following details shall be specified: test method to be used (A, B or C); elements of connection mated or unmated; r.m.s. value of the test voltage specified for the particular test, e.g.environmental, contamination, humidity, air pressure, temperature tests, etc.; maximu

24、m permissible leakage current, where applicable. 4 Methods The a.c. test voltage indicated in the technical specification shall be applied for (60 5)s per method A, B or C, as specified by the technical specification. The test voltage shall have a40Hz to60Hz frequency and application rate shall not

25、exceed500V/s. 4.1 Method A The test voltage shall be applied in turn between each contact and all the others connected together and to the housing (shell) or the mounting plate. 4.2 Method B Alternate contacts shall be connected together to form two groups, one including all even numbered contacts,

26、the second all odd numbered contacts, for instance. The test voltage shall be applied in turn between: the first group of contacts and the second group connected to the housing (shell) or the mounting plate; the second group of contacts and the first group connected to the housing (shell) or the mou

27、nting plate. In the case of contacts arranged in two or more rows, it may be necessary to form a second arrangement of two groups in order to apply the voltage between all adjacent contacts. 4.3 Method C The specimen shall be subjected to the test voltage between two adjacent contacts or between one

28、 contact and the housing (shell) having a minimum spacing. 4.4 Requirements There shall be no breakdown or spark-over and the specified maximum leakage current shall not be exceeded when the test voltage is applied.4 blankBSEN2591-207:1996 BSI 11-1999 List of references See national foreword.BS EN 2

29、591-207:1996 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishS

30、tandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while us

31、ing this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically recei

32、ve the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation

33、of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information s

34、ervices are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For detai

35、ls of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright,

36、 Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the stand

37、ard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.