EN 149-2001 en Respiratory protective devices - Filtering half masks to protect against particles - Requirements testing marking (Incorporates Amendment A1 2009)《呼吸防护装置 颗粒防护用过滤半面罩 .pdf

《EN 149-2001 en Respiratory protective devices - Filtering half masks to protect against particles - Requirements testing marking (Incorporates Amendment A1 2009)《呼吸防护装置 颗粒防护用过滤半面罩 .pdf》由会员分享，可在线阅读，更多相关《EN 149-2001 en Respiratory protective devices - Filtering half masks to protect against particles - Requirements testing marking (Incorporates Amendment A1 2009)《呼吸防护装置 颗粒防护用过滤半面罩 .pdf（44页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDRespiratory protective devices Filtering half masks to protect against particles Requirements, testing, markingICS 13.340.30g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60

2、g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 149:2001 +A1:2009Incorporating corrigendum July 2002BS EN 149:2001This British Standard was published under the authority of the Standards Committee on 15 June 2001 BSI National forewordThe start and finish of text introduced or altered by amendment is i

3、ndicated in the text by tags. Tags indicating changes to CEN text carry the number of the CEN amendment. For example, text altered by CEN amendment A1 is indicated by .The UK participation in its preparation was entrusted to Technical Committee PH/4, Respiratory protection.A list of organizations re

4、presented on this subcommittee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amend

5、ments/corrigenda issued since publicationAmd. No. Date Comments 14080 Corrigendum No. 123 January 2003Changes to Clause 6, 8.9.1.1, 8.9.1.2, Figure 11 and Table 431 July 2009 Implementation of CEN amendment A1:20092009ISBN 978 0 580 62117 8+A1:2009 abThis British Standard is the UK implementation of

6、 EN 149:2001+A1:2009 incorporating Corrigendum July 2002. It supersedes BS EN 149:2001 which is withdrawn.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 149:2001+A1 May 2009 ICS 13.340.30 Supersedes EN 149:2001English Version Respiratory protective devices - Filtering half masks to protect aga

7、inst particles - Requirements, testing, marking Appareils de protection respiratoire - Demi-masques filtrants contre les particules - Exigences, essais, marquageAtemschutzgerte - Filtrierende Halbmasken zum Schutz gegen Partikeln - Anforderungen, Prfung, KennzeichnungThis European Standard was appro

8、ved by CEN on 8 March 2001 and includes Corrigendum 1 issued by CEN on 24 July 2002 and Amendment 1 approved by CEN on 26 March 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national st

9、andard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any oth

10、er language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia

11、, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPIS

12、CHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 149:2001+A1:2009: EEN 149:2001+A1:2009 (E) 2 Contents Page Foreword 4g3Introduction . 4g31g3 Scope 4g

13、32g3 Normative references 5g33g3 Terms and definitions . 5g34g3 Description . 5g35g3 Classification . 5g36g3 Designation 6g37g3 Requirements 6g37.1g3 General . 6g37.2g3 Nominal values and tolerances . 6g37.3g3 Visual inspection . 6g37.4g3 Packaging 6g37.5g3 Material . 6g37.6g3 Cleaning and disinfect

14、ing 6g37.7g3 Practical performance . 7g37.8g3 Finish of parts 7g37.9g3 Leakage 7g37.10g3 Compatibility with skin . 8g37.11g3 Flammability 8g37.12g3 Carbon dioxide content of the inhalation air 9g37.13g3 Head harness . 9g37.14g3 Field of vision 9g37.15g3 Exhalation valve(s) 9g37.16g3 Breathing resist

15、ance . 9g37.17g3 Clogging . 10g3BS EN 149:2001+A1:2009 EN 149:2001+A1:2009 (E) 3 7.18g3 Demountable parts 11g38g3 Testing . 11g38.1g3 General . 11g38.2g3 Visual inspection . 11g38.3g3 Conditioning 11g38.4g3 Practical performance 12g38.5g3 Leakage 13g38.6g3 Flammability 16g38.7g3 Carbon dioxide conte

16、nt of the inhalation air 17g38.8g3 Strength of attachment of exhalation valve housing 18g38.9g3 Breathing Resistance 18g38.10g3 Clogging . 19g38.11g3 !Penetration of filter material . 20g39g3 Marking 21g39.1g3 Packaging 21g39.2g3 Particle filtering half mask . 21g310g3 Information to be supplied by

17、the manufacturer . 22g3Annex A (informative) Marking 38g3Annex ZA . (informative) Clauses of this European Standard addressing essential requirements or other provisions of EU Directives . 39g3Bibliography 41g3BS EN 149:2001+A1:2009 EN 149:2001+A1:2009 (E) 4 Foreword This document (EN 149:2001+A1:20

18、09) has been prepared by Technical Committee CEN/TC 79 “Respiratory protective devices“, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2009, and

19、 conflicting national standards shall be withdrawn at the latest by November 2009. This European Standard supersedes !EN 149:2001“. This European Standard was approved by CEN on 8 March 2001 and includes Corrigendum 1 issued by CEN on 24 July 2002 and Amendment 1 approved by CEN on 26 March 2009. Th

20、e start and finish of text introduced or altered by amendment is indicated in the text by tags !“. The modifications of the related CEN Corrigendum have been implemented at the appropriate places in the text and are indicated by the tags . This European Standard has been prepared under a mandate giv

21、en to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this standard. Annex A is informative. According to the CEN/CENELEC Inte

22、rnal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Ma

23、lta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Introduction A given respiratory protective device can only be approved when the individual components satisfy the requirements of the test specification which may be a complet

24、e standard or part of a standard, and practical performance tests have been carried out successfully on complete apparatus where specified in the appropriate standard. If for any reason a complete apparatus is not tested then simulation of the apparatus is permitted provided the respiratory characte

25、ristics and weight distribution are similar to those of the complete apparatus. 1 Scope This European Standard specifies minimum requirements for filtering half masks as respiratory protective devices to protect against particles except for escape purposes. Laboratory and practical performance tests

26、 are included for the assessment of compliance with the requirements. BS EN 149:2001+A1:2009 EN 149:2001+A1:2009 (E) 5 2 Normative references !The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated

27、references, the latest edition of the referenced document (including any amendments) applies.“ EN 132, Respiratory protective devices - Definitions of terms and pictograms EN 134, Respiratory protective devices - Nomenclature of components EN 143, Respiratory protective devices - Particle filters -

28、Requirements, testing, marking !EN 13274-7, Respiratory protective devices Methods of test Part 7: Determination of particle filter penetration“ ISO 6941, Textile fabrics - Burning behaviour - Measurement of flame spread properties of vertically oriented specimens 3 Terms and definitions For the pur

29、poses of this European Standard the definitions given in EN 132 and the nomenclature given in EN 134 apply !together with the following: 3.1 re-useable particle filtering half mask particle filtering half mask intended to be used for more than a single shift“ 4 Description A particle filtering half

30、mask covers the nose and mouth and the chin and may have inhalation and/or exhalation valve(s). The half mask consists entirely or substantially of filter material or comprises a facepiece in which the main filter(s) form an inseparable part of the device. It is intended to provide adequate sealing

31、on the face of the wearer against the ambient atmosphere, when the skin is dry or moist and when the head is moved. Air enters the particle filtering half mask and passes directly to the nose and mouth area of the facepiece or, via an inhalation valve(s) if fitted. The exhaled air flows through the

32、filter material and/or an exhalation valve (if fitted) directly to the ambient atmosphere. These devices are designed to protect against both solid and liquid aerosols. 5 Classification Particle filtering half masks are classified according to their filtering efficiency and their maximum total inwar

33、d leakage. There are three classes of devices: FFP1, FFP2 and FFP3. The protection provided by an FFP2 - or FFP3 - device includes that provided by the device of lower class or classes. !In addition, particle filtering half masks are classified as single shift use only or as re-usable (more than one

34、 shift).“ BS EN 149:2001+A1:2009 EN 149:2001+A1:2009 (E) 6 6 Designation Particle filtering half masks meeting the requirements of this European Standard shall be designated in the following manner: !Particle filtering half mask EN 149, year of publication, classification, option (where “D“ is an op

35、tion for a non re-useable particle filtering half mask and mandatory for re-useable particle filtering half mask).“ !EXAMPLE Particle filtering half mask EN 149:2001 FFP1 NR D “ 7 Requirements 7.1 General In all tests all test samples shall meet the requirements. 7.2 Nominal values and tolerances Un

36、less otherwise specified, the values stated in this European Standard are expressed as nominal values. Except for temperature limits, values which are not stated as maxima or minima shall be subject to a tolerance of 5 %. Unless otherwise specified, the ambient temperature for testing shall be (16 -

37、 32) C, and the temperature limits shall be subject to an accuracy of 1 C. 7.3 Visual inspection The visual inspection shall also include the marking and the information supplied by the manufacturer. 7.4 Packaging Particle filtering half masks shall be offered for sale packaged in such a way that th

38、ey are protected against mechanical damage and contamination before use. Testing shall be done in accordance with 8.2. 7.5 Material Materials used shall be suitable to withstand handling and wear over the period for which the particle filtering half mask is designed to be used. After undergoing the

39、conditioning described in 8.3.1 none of the particle filtering half masks shall have suffered mechanical failure of the facepiece or straps. Three particle filtering half masks shall be tested. When conditioned in accordance with 8.3.1 and 8.3.2 the particle filtering half mask shall not collapse. A

40、ny material from the filter media released by the air flow through the filter shall not constitute a hazard or nuisance for the wearer. Testing shall be done in accordance with 8.2. 7.6 Cleaning and disinfecting !If the particle filtering half mask is designed to be re-usable, the materials used sha

41、ll withstand the cleaning and disinfecting agents and procedures to be specified by the manufacturer.“ BS EN 149:2001+A1:2009 EN 149:2001+A1:2009 (E) 7 Testing shall be done in accordance with 8.4 and 8.5. !With reference to 7.9.2, after cleaning and disinfecting the re-usable particle filtering hal

42、f mask shall satisfy the penetration requirement of the relevant class. Testing shall be done in accordance with 8.11.“ 7.7 Practical performance The particle filtering half mask shall undergo practical performance tests under realistic conditions. These general tests serve the purpose of checking t

43、he equipment for imperfections that cannot be determined by the tests described elsewhere in this standard. Where practical performance tests show the apparatus has imperfections related to wearers acceptance, the test house shall provide full details of those parts of the practical performance test

44、s which revealed these imperfections. Testing shall be done in accordance with 8.4. 7.8 Finish of parts Parts of the device likely to come into contact with the wearer shall have no sharp edges or burrs. Testing shall be done in accordance with 8.2. 7.9 Leakage 7.9.1 Total inward leakage The laborat

45、ory tests shall indicate that the particle filtering half mask can be used by the wearer to protect with high probability against the potential hazard to be expected. The total inward leakage consists of three components: face seal leakage, exhalation valve leakage (if exhalation valve fitted) and f

46、ilter penetration. For particle filtering half masks fitted in accordance with the manufacturers information, at least 46 out of the 50 individual exercise results (i.e. 10 subjects x 5 exercises) for total inward leakage shall be not greater than 25 % for FFP1 11 % for FFP2 5 % for FFP3 and, in add

47、ition, at least 8 out of the 10 individual wearer arithmetic means for the total inward leakage shall be not greater than 22 % for FFP1 8 % for FFP2 2 % for FFP3. Testing shall be done in accordance with 8.5. BS EN 149:2001+A1:2009 EN 149:2001+A1:2009 (E) 8 7.9.2 Penetration of filter material The p

48、enetration of the filter of the particle filtering half mask shall meet the requirements of Table 1. Table 1 Penetration of filter material Classification !Maximum penetration of test aerosol“ Sodium chloride test 95 l/min Paraffin oil test 95 l/min % % max. max.FFP1 20 20 FFP2 6 6 FFP3 1 1 !A total

49、 of 9 samples of particle filtering half masks shall be tested for each aerosol. Testing in accordance with 8.11 using the Penetration test according to EN 13274-7, shall be performed on: - 3 samples as received; - 3 samples after the simulated wearing treatment described in 8.3.1. Testing in accordance with 8.11 using the Exposure test with a specified mass of test aerosol of 120 mg, and for particle filtering devices claimed to be re-usable additionally the Storage test, according to EN 13274-7, shall be performed: - for non-re-usable devices on: - 3