EN 1313-2-1998 en Round and Sawn Timber - Permitted Deviations and Preferred Sizes - Part 2 Hardwood Sawn Timber (Incorporating Corrigendum June 1999)《圆木材和木板材 允许偏差和优选尺寸 第2部份 阔叶木板材 .pdf

《EN 1313-2-1998 en Round and Sawn Timber - Permitted Deviations and Preferred Sizes - Part 2 Hardwood Sawn Timber (Incorporating Corrigendum June 1999)《圆木材和木板材 允许偏差和优选尺寸 第2部份 阔叶木板材 .pdf》由会员分享，可在线阅读，更多相关《EN 1313-2-1998 en Round and Sawn Timber - Permitted Deviations and Preferred Sizes - Part 2 Hardwood Sawn Timber (Incorporating Corrigendum June 1999)《圆木材和木板材 允许偏差和优选尺寸 第2部份 阔叶木板材 .pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、Round and sawn timber - Permitted deviations and preferred sizes - Part 2: Hardwood sawn timber The European Stanard EN 1313-2: 1998 has the status of a British Standard ICs 79.040 5s EN .313-2:1999 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYBIGi LAW STD-BSI BS EN 3313-2-ENGL 1999

2、= Lb2Libb9 0866033 bL2 BS EN 1313-2:1999 - been ppared under the direction of the Sector Committee for Building and Ci Engineeing, was published under the authority of the standards Committee and comes into effect on 16 March 1999 Amd No. 10981 No. 1 8 BSI 082000 National foreword Date Text affected

3、 August 2000 Indicated by a sideline. This Brijsh StanM is the English language version of EN 131S2 1998, including conigendum August 2000. It Supersedes BS 5450:1977 which is withdram The UK participation in its preparation was entrusted by Technical Committee W54.3, Round and sawn timber, to Subco

4、mmittee B/543/2, Sawn timber, which has the responsibility to: - aid enquirers to understand the text; - present to the responsible European committee any enquiries on the - monitor related internaiional and European developments and promulgate interpretation, or proposals for change, and keep the U

5、K interests informed; them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secrem. National annex NA (informative) contains the recommended reduction of sawn hardwood by processing. Cross-references The British Stan& which implement intemationai

6、or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “Intemationai Standards Correspondence Index“, or by using the “Find“ facility of the BSI Standards Electronic Catalogue. Informative reference BS 57561997, Sfkaton for visual

7、 stmyth gmding of hardwood. A British Standard does not purport to include all the necessary provisions of a contract Users of British standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legd obligations. Summary of page

8、s This document comprises a front cover, an inside front cover, the EN tide page, pages 2 to 4, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. ISBN O 680 32079 O STDeBSI BS EN L313-2-ENGL 1949 = Lb24bb9 OBbb034

9、559 EuRopEANsrANDARD EN 13132 NORME EUR0PEE”E EUROP- NORM November 1998 ICs 79.040 Incorporating conigendum June 1999 kript wood, sawlogs, sawn timber, hardwood, dimensional deviations, dimensionai stabiity, humidity, dimensions English version RoundandSaWnthber- Permitted deviations and preferred s

10、izes - Part2 Hardwood sawntimber Bois mnds et bois scis - Ecars admissibles et imensions p&Entielles - partie 2: Bois scis feuillus hd- und Schnioh - Zuhssige AbWeiChUngen und VOIZUKE& - Teil2Laubschni tthOlZ This European Standard was approved by CEN on 8 November 1998. CEN members are bound to com

11、ply with the CENKENELEC Internai Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration Uptodate lists and bibliographicd references concerning such national standards may be obtained on application to the Centrai Secreta

12、riat or to any CEN member. This European Standard exists in three official versions (English, French, German). Aversion in any other ianguage made by translation under the responsibility of a CEN member into its own language and noed to the Central Secretariat has the same status as the official ver

13、sions. CEN members are the national standards bodies of Ausria, Belgium, Czech Republic, Denmark, Fnland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and Unitd Kingdom. CEN European Committee for Standardization Comit Europe

14、n de Normalisation Europisches Komitee fur Normung Central Secretariat: rue de Stassart 36, B-1060 Brussels O 1998 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members Ref. No. EN 1313-2:1998 E STD=BSI BS EN II3L3-2-ENGL II999 D II624669 0866035 495

15、 D Page 2 EN 1313-21998 Foreword This European Standard has been prepared by Technical Committee CENlC 175, Round and sawn timber, the Secretariat of which is held by AFNOR. This European Standard shali be given the status of a national stan- either by publication of an identical text or by endorsem

16、ent, at the latest by May 1999, and confiicting national standards shall be withdrawn at the latest by May 1999. According to the CEN/CENELEC Internai Regukions, the national standards organizations of the foiiowing counties are bound to implement this European Stan- Austria, Belgium, Czech Republic

17、, Denmark, Fnland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzeriand and the United Kingdom This standard is one of two conceniing permitted deviations and preferred sizes of sawn timber. The other standard is: EN 1313-1, Round an

18、d sawn timber- Permitted dayiations and pqfd sizes - Part 1: SoJEwood sawn timber. Contents Foreword 1 Scope 2 Normative references 3 Definitions 4 Moisturecontent 5 Change in size due to changes in moisture content 6 Permitfeddeviations 7 Preferredsizes Annex A (informative) Complementary national

19、sizes page 2 3 3 3 3 3 3 3 4 Q BSI 082000 STD-ES1 BS EN 1333-2-ENGL 1979 1624bb9 OBbb03b 321 Page 3 EN 1313-21998 1 scope This European Standard specifies permitted deviations and preferred sizes of European hardwood sawn timber at a moisture content of 20 %. 2 Normative references This European Sta

20、ndard incorporates, by dated or undated reference, provisions from other pubiicaons. These nonnative references are cited at the appropriate piaces in the text and the pubidons are listed hereafta For dated references, subsequent amendments to or revisions of any of these publications appiy to this

21、European Standard oniy when incorporated in it by amendment or revision. For undated references, the latest edition of the publication refemd to applies. EN 336, SEruchmL timber- ConiferozLs and poplar- sizes, pemwle d,#iuth. EN 844-1, Round and sawn timber- Tminabgy- part 1: Genmd terms common to m

22、nd timber and sawn timber. EN 844-3, Round and sawn timber- Tminabgy- Part3: kneml terms relating to sawn timber. EN 844-4, Round and sawn timber- hindogy- Partk lbms rehting to moishm content. EN 844-6, Round and sawn timber- Tmmbgy- Part 6: Terms relating to dimensms of sawn timber. EN 1309-1, Rou

23、nd and sawn tinaber- Method of measumt of dim - Part 1: Sawn timber. prEN 13183-1, Round and sawn timber- Method of measuremat of nwistum content - Part 1: Method for determining moisture content of a piece of sawn timber (Oven-dr.q method). prEN 13183-2, Round and sawn tiwtber- Method of measuremen

24、t of rrwishre content - Part 2: Method for estimating misi?uw content of a piece of sawn timber (ElecW method). 3 Denitions For the purposes of this standard, the definitions contained in EN 844-1, EN 844-3, EN 844-4 and EN 844-6 apply. 4 Moisture content The measurement of moisture content sha be c

25、arried out according to prEN 13183-1 or prEN 131B2. The reference moisture content is 20 %. 6 Change in size due to changes in moisture content Unies there is evidence to the contrary, it is assumed that the thickness and width of a piece of timber will increase by 0,25 % for every 1 % of moisture c

26、ontent higher than 20 % up to 30 %, and wiii decrease by 0,25 % for every 1 % of moisture content lower than 20 %. The above values are independent of the species. 6 Permitted deviations For a specifed number of pieces of hardwood sawn timber of the same target thickness andor width, the average thi

27、ckness andor width shall not be les than the target thickness andor widh. If the timber is for structural use, the permitted deviations shall be those specified in EN 336. The permitted deviations, at a moisture content of 20 %, are the foliowing. 6.1 On thicknesses (t) t 32mm: -lm, +3m1 t32mm: -2mm

28、,+4111 The permitted deviations of thickn- appiy to all thicknesses, not ony to preferred ones. 6.2 On widths (b) bs100mm: -2nt1, +6mm b 200m 1OOmm c b s 200 m -3mm, +9 mm I -4 mm, +12 mm 6.3 On lengths (2) - For unedged timber O, +3 % of the target and boules: length but no more than90mm. -For squa

29、re edged O, +3 % of the target timber. length but no more than90mm. 7 Preferred sizes Sizes are measured according to EN 1309-1 at a moisture content of 20 %. 7.1 Preferred thicknesses 20mm,27mm,32mm,40mm,50mm,60mm, 65 mm, 70 mm, 80 mm and 100 mm 7.2 Preferred widths 10 mm intervals for widths betwe

30、en 60 mm and 90 mm 20 mm intervals for widths of 100 nun or more 7.3 Preferred lengths For unedged timber and boules: OJO m intervals for lengths between 2,00 m and 6,00 m For square edged timber: 0,05 m intervals where I I i,00 m O, 10 m intends where I 1,OO m STD-BSI BS EN 1313-2-ENGL 1999 9 1b24b

31、b9 08bb037 268 m Page 4 EN 1313-2199s Annex A (informative) Complementary national sizes Complementary preferred sizes in Germany (DE) Thicknesses (in millimetres): 18 22 Thickness of the board for all standardized pallets 24 Standardized thickness of the industrid packages 25 30 35 45 52 63 78 “hic

32、knw of the blocks for all the standardized pallets Width (in miilimetres): 145 Width of the boards in standardized pailets, especially in Ewepallets Complementary preferred sizes in the United Kingdom (GB) Thicknesses (in millimetres): 19,26,38,52,63,75 Complementary preferred sizes in Ireland (IR)

33、Thicknesses (in milhetres): 25,38, 63,75 Complementary preferred sizes in Italy (IT) Width (in millimetres): 250 Complementary preferred sizes in the Netherlands (NL) Thicknesses (in millimetres): 15,18,26,34,41,45,52, 54,63,75 Complementary preferred sizes in Norway (NO) Width (in millimetres): 63,

34、75,125,160,250 Complementary preferred sizes in France (FR) Thicknaes (in millimetres): 3655 Q BSI 082000 National annex NA (informative) Reduction of sawn hardwoods by processing NA.1 General Processing of hardwoods to accurate finished sizes involves rextions in size which vary with the size, the

35、process and the product. The figures in Table NA1 have been established in the United Kingdom as being economic, workable and not wasteful. NA.2 Reductions The recommended reductions appropriate to some end uses and products appear in Table NA.1. Any finished sizes in British Standards covering part

36、icular hardwood products and components will take precedence over those in Table NA1. For other end uses not specifically mentioned, the same figures as those for one of the end uses listed may be adopted. intermediate figures would be unlikely to achieve any greater accuracy and would tend to confu

37、se. If the timber is for structurai use, the reduction hits specified in BS 6766 apply. NA.3 Permitted deviations For all finished sizes after processing, permitted deviations of fo,5 mm are recommended If the timber is for structurai use, the permitted deviations specified in BS EN 336 apply. End u

38、se or product Floorings,matchingsand interlocked boarding and planed aii round nhn Joinery and cabinet wood Reduction from sawn size to ilnished target size For target sizes of width or thickness 15 to 26 26to 50 51 to 100 101 to 150 151 to 300 5 6 7 7 7 6 7 8 9 10 7 9 10 12 14 BS EN 1313-2:1999 BSI

39、 STDaBSI BS EN L313-2-ENGL 1799 E Lb24669 O866037 030 389 Chiswi High Road London w4 4AL BSI - British Standards Institution BSI is the independent nationai body responsible for preparing British Stan&. It presents the UK view on standards in Europe and at the international level. It is incorporated

40、 by Royal Charter. Revisions British Standards are updated by amendment or revision Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant alln of BSI to improve the quality of our products and services. We would be grateful if anyone finc

41、ling an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identiy of which can be found on the inside front cover, Tel: 020 8996 9OOO. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS whic

42、h ensures that subscribers automaticaiiy receive the last editions of standards. Buying standards rders for all BSI, intemational and foreign standards publications should be addressed to Customer Services. Tel: O20 8996 9001. Fax 020 8996 7001. In response to orders for intedonal standards, it is B

43、SI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested Information on standards BSI provides a wide range of information on nationai, European and intemationai standards through its Library and its Technid Help to Exporters Servi

44、ce. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax 020 8996 7048. Subscribing members of BSI axe kept up to date with standards developments and receive sub&mtiaJ discounts on

45、 the purchase price of standards. For details of these and other benets contact Membership Fax O20 8996 7001. -on. Tel: O20 8996 7002. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of he publications of the international standadhation bodies. Except a

46、s permitted under the copyright, Designs and Patents Act 1988 no extract may be reproduced, -red in a rexievai system or transmitted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission from BSL lbis does not preclude the free use, in the

47、course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these ietails are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained if permission is granted, the temis may include royalty payments or a licensing greement. Details and advice can be obtained from the copyright Manager. kk O20 8996 7070.