EN 12710-2006 en Fibreboard Drums - Removable Head (Open Head) Drums with Closing Rings with a Nominal Capacity of 15 l to 250 l《纤维纸板筒 标称容量15～250升带锁紧圈的活动头(开口)纸筒》.pdf

《EN 12710-2006 en Fibreboard Drums - Removable Head (Open Head) Drums with Closing Rings with a Nominal Capacity of 15 l to 250 l《纤维纸板筒 标称容量15～250升带锁紧圈的活动头(开口)纸筒》.pdf》由会员分享，可在线阅读，更多相关《EN 12710-2006 en Fibreboard Drums - Removable Head (Open Head) Drums with Closing Rings with a Nominal Capacity of 15 l to 250 l《纤维纸板筒 标称容量15～250升带锁紧圈的活动头(开口)纸筒》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARDBS EN 12710:2006Fibreboard drums Removable head (open head) drums with closing rings with a nominal capacity of 15 l to 250 lThe European Standard EN 12710:2006 has the status of a British StandardICS 55.140g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48

2、g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 12710:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2006 BSI 2006ISBN 0 580 48887 XNational forewor

3、dThis British Standard is the official English language version of EN 12710:2006. It supersedes BS EN 12710:2000 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PKW/0, Packaging, which has the responsibility to: A list of organizations represented on t

4、his committee can be obtained on request to its secretary.Cross-referencesThe British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using

5、 the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from

6、 legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK.Su

7、mmary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 15 and a back cover.The BSI copyright notice displayed in this document indicates when the document was last issued.Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARDNORM

8、E EUROPENNEEUROPISCHE NORMEN 12710May 2006ICS 55.140 Supersedes EN 12710:1999 English VersionFibreboard drums - Removable head (open head) drums withclosing rings with a nominal capacity of 15 l to 250 lFts en carton - Fts ouverture totale dune capacitnominale de 15 l 250 lFibertrommeln - Deckelfsse

9、r mit Spannringen mit einemNennvolumen von 15 l bis 250 lThis European Standard was approved by CEN on 28 April 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any

10、 alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by tr

11、anslationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hu

12、ngary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre:

13、rue de Stassart, 36 B-1050 Brussels 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12710:2006: EEN 12710:2005 (E) 2 Contents Page Foreword .3 Introduction.4 1 Scope5 2 Normative references5 3 Terms and definitions .5 4 Dimensio

14、ns 6 5 Materials .8 6 Requirements.9 7 Designation 9 Annex A (normative) Fibreboard drum dimensions 11 Annex B (normative) Fibreboard drum preferred diameter-capacity relationship 12 Annex C (informative) Fitness for use .13 Annex D (informative) Fibreboard drum material identification symbols 14 Bi

15、bliography15 EN 12710:2006 (E) 3 Foreword This document (EN 12710:2006) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or b

16、y endorsement, at the latest by November 2006, and conflicting national standards shall be withdrawn at the latest by November 2006. This document supersedes EN 12710:1999 According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to

17、implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and U

18、nited Kingdom. EN 12710:2006 (E) 4 Introduction This standard is limited to the specification of constructional details and the establishment of a preferred range of diameters and capacities for fibreboard drums, in recognition of the fact that one of the important characteristics of fibreboard drum

19、s is that they can be produced in various ranges of diameters and heights with constructions to suit specific products and market needs and can be fitted with a variety of lids, bases and fasteners. EN 12710:2006 (E) 5 1 Scope This European Standard specifies the construction requirements for cylind

20、rical fibreboard drums with a nominal capacity of 15 l to 250 l and the preferred range of diameters and capacities. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated ref

21、erences, the latest edition of the referenced document (including any amendments) applies. EN ISO 2233:2001, Packaging Complete, filled transport packages and unit loads Conditioning for testing (ISO 2233:2000) 3 Terms and definitions For the purposes of this European Standard, the following terms a

22、nd definitions apply. 3.1 fibreboard drum rigid, cylindrical container with a sidewall, made of multiple plies of virgin or recycled paper or board firmly bonded together, and a base, firmly connected to the sidewall and a bottom chimb, and a top, which can be removed as a lid and closed by means of

23、 the closing ring over the top chimb, the chimb being secured to the sidewall 3.2 nominal capacity (NC) capacity in litres which, by convention, is used to represent a class of drums of similar brimful capacities 3.3 sidewall cylindrical body of the drum 3.4 lid removable top of the drum 3.5 chimb t

24、op or bottom rim of the drum 3.6 internal lining fixed inner ply of material, other than that which is used for the general construction of the drum, used to give the drum specific properties 3.7 external lining fixed outer ply of material, other than that which is used for the general construction

25、of the drum, used to give the drum specific properties EN 12710:2006 (E) 6 3.8 barrier multiple or single ply of material, other than that which is used for the general construction of the drum, incorporated into the sidewall, lid or base of the drum 3.9 liner separate bag or semi-rigid container, u

26、sed inside the drum to give the drum specific properties 3.10 internal coating material applied to the inner surface of the drum, by spray, brush or other means to give the drum specific properties 3.11 external coating material applied to the outer surface of the drum, by spray, brush or other mean

27、s to give the drum specific properties 3.12 closing ring band by which a lid can be held to the top of the drum and secured in position by means of a fastening device 3.13 base horizontal bottom wall of the drum 4 Dimensions 4.1 General The drum description shall include the dimensions listed in 4.2

28、 and 4.3. In addition the description shall include the nominal capacity as determined in 4.4. Drum dimensions are shown in annex A. 4.2 Diameter 4.2.1 Nominal internal diameter The nominal internal diameter is used only to provide a classification of drum diameters. 4.2.2 Internal diameter (d1) The

29、 internal diameter (d1), in millimetres, is the internal measurement from the inner sidewall to the diametrically opposite inner sidewall. 4.2.3 Outside diameter (d2) The outside diameter (overall diameter) (d2), in millimetres, is the measurement over the closing ring, but not over the fastening de

30、vice. EN 12710:2006 (E) 7 4.3 Height and depth 4.3.1 Internal height (h1) The internal height (h1), in millimetres, is the height from the inner surface of the drum base to the top surface of the top inner bead profile. This dimension indicates the maximum filling height. 4.3.2 External height (h2)

31、The external height (h2), in millimetres, is the height from the lowest point of the drum to the top edge of the closing ring. 4.3.3 Stacking height The stacking height, in millimetres, of the drum is calculated by: height of a stack of N drums = (N - 1) x h2+ h3. 4.3.4 Overall height (h3) The overa

32、ll height (h3), in millimetres, is the height of a drum closed for despatch, measured from the lowest point of the drum to the highest point of the lid. NOTE Depending on lid design, overall height (h3) and external height (h2) may be the same. In all designs the difference between h3and h2, (h3- h2

33、), shall not be greater than the chimb depth (h4) to ensure stability of stacking. 4.3.5 Chimb depth (h4) The chimb depth (h4), in millimetres, is the measurement from the lowest point of the chimb to the underside of the base. 4.4 Capacity calculations 4.4.1 Nominal capacity (NC) The nominal capaci

34、ty (see 3.2) is the internal volume, in litres, to the top internal bead of the drum as calculated from the dimensions d1and h1. 4.4.2 Shipping cube Dimensions d2and h3are used to calculate the shipping cube. 4.5 Tolerances As drums are manufactured from materials which are subject to dimensional an

35、d weight variations according to changes in atmospheric conditions, all dimensions and tolerances are quoted on completed drums which have been conditioned for 24 h at 23 C 2 C and 50 % 2 % r.h., in accordance with EN ISO 2233:2000, Condition 7. NOTE Short term fluctuations and measurement limitatio

36、ns may cause individual measurements to vary up to 5 % relative humidity. EN 12710:2006 (E) 8 4.5.1 Mass tolerance The mass tolerance is 5 % of the mass, in kilograms, of a complete drum. 4.5.2 Manufacturing tolerances The manufacturing tolerances applicable to dimensions shall be: a) all diameters

37、2,0 mm; b) all heights 5,0 mm. 4.6 Capacity requirements 4.6.1 General As fibreboard drums provide numerous variations in size, construction and design type, they can be adapted to suit the purchasers packaging and capacity requirements. 4.6.2 Preferred range of nominal capacities The preferred rang

38、e of nominal capacities is 15 l, 20 l, 25 l, 30 l, 40 l, 50 l, 60 l, 80 l, 100 l, 120 l, 150 l, 200 l, 220 l and 250 l. NOTE Annex B shows the preferred relationship between drum diameter and nominal capacity. 4.6.3 Other capacities Other capacities are available by arrangement between the purchaser

39、 and the supplier. 5 Materials 5.1 Sidewall The sidewall of the drum shall consist either of convolutely or spirally wound plies of virgin or recycled paper or fibreboard firmly bonded together. NOTE The sidewall may incorporate one or more layers of protective material (internal or external lining/

40、barrier), the type and number of which are determined by specification details. 5.2 Base and lid The base and lid shall be manufactured from any single or composite material. NOTE The base and lid may incorporate protective linings or barriers to meet specification requirements. The base and lid sha

41、ll be attached to the sidewall in such a way as to give adequate protection to the contents of the drum. 5.3 Chimbs Chimbs shall be manufactured from any single or composite material and shall be secured to the sidewall by pressing, rolling or other means. EN 12710:2006 (E) 9 5.4 Closing ring The cl

42、osing ring shall be made of metal, plastics or any other suitable material. 5.5 Internal and external treatments Any internal or external treatment such as a lining, a liner, or coating, shall be made of a material compatible with the contents of the drum and suitable for the intended use of the dru

43、m as notified by the purchaser. (See annex C.) 5.6 Barrier A barrier shall be made of multiple or single ply material, incorporated into the sidewall, lid and base of the drum to resist the transmission of gas or vapour into, or out of the drum. 6 Requirements 6.1 Material identification symbols 6.1

44、.1 Drum materials All drums shall carry the relevant material identification code printed on the lowest possible point of the external sidewall or bottom chimb, i.e. the code identifying material from which the drum is made. Fibreboard drum material identification symbols are given in annex D. 6.1.2

45、 Plastics components All plastics components, excluding gaskets, shall be permanently marked with the relevant identification symbol, i.e. the symbol identifying the material from which the component is made. 7 Designation A removable head (open head) drum (OH) manufactured in accordance with EN 127

46、10 with a nominal capacity (NC) of 15 l to 250 l and an internal diameter (d1) of 250 mm to 630 mm shall be designated: Fibreboard drum OH EN 12710 NC - 15 l to 250 l. d1- 250 mm to 630 mm. EXAMPLE A fibreboard drum with a nominal capacity of 100 l, having an internal diameter of 450 mm would be des

47、ignated: Fibreboard drum OH EN 12710 NC-100 l. d1-450 mm NOTE Where the drums are intended to be used for the transport of dangerous goods, attention is drawn to the regulatory requirements which govern the transport of those goods in the countries concerned. In Europe, depending upon the mode of tr

48、ansport, this means meeting the requirements of: European Agreement Concerning the International Carriage of Dangerous Goods by Road (ADR); Regulations concerning the International Carriage of Dangerous Goods by Rail (RID); Technical Instructions for the Safe Transport of Dangerous Goods by Air, Doc

49、ument 9284-AN/905 published by the Council of the International Civil Aviation Organization (ICAO); EN 12710:2006 (E) 10 The International Maritime Dangerous Goods Code (IMDG-CODE) published by the International Maritime Organization (IMO). EN 12710:2006 (E) 11 Annex A (normative) Fibreboard drum dimensions Key 1 outside diameter, d2 2 internal diameter, d13 internal height, h14 external height, h25 overall height, h36 chimb depth, h4Figure A.1 Dimensions drum of circular cross section with curled profile base, lid and closing ring EN 12710:2006 (