EN 12100-1997 en Plastics Piping Systems - Polyethylene (PE) Valves - Test Method for Resistance to Bending between Supports《塑料管道系统 聚乙烯(PE)阀 三点负载抗弯曲试验方法》.pdf

《EN 12100-1997 en Plastics Piping Systems - Polyethylene (PE) Valves - Test Method for Resistance to Bending between Supports《塑料管道系统 聚乙烯(PE)阀 三点负载抗弯曲试验方法》.pdf》由会员分享，可在线阅读，更多相关《EN 12100-1997 en Plastics Piping Systems - Polyethylene (PE) Valves - Test Method for Resistance to Bending between Supports《塑料管道系统 聚乙烯(PE)阀 三点负载抗弯曲试验方法》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、 STD.BS1 BS EN Z2LO-ENGL 1798 D Lb24bb7 b82237 457 BRITISH STANDARD Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to bending between supports The European Standard EN 12100 : 1997 has the status of a British Standard ICs 23.060.01 BS EN 12100 : 1998 BS 2782 : Part 1

2、1 : Method 1133D : 1997 BS EN 12100 : 1998 Amd No. Date National foreword - Text affected This British Standard is the English language version of EN 12100 : 1997 published by the European Committee for Standardization (CEN). This European Standard is incorporated into BS 2782 Methods of testing phs

3、tics : Part 11: lhemwplastics pipes, fittings and valves, as Method 1133D, for association with related test methods for plastics materials and plastics piping components. The UK participation in its preparation was entrusted to Technical Committee PW61, Plastics piping systems and components, which

4、 has the responsibility to: - aid enquirers to understand the text; - present to the responsible internationaVEuropean committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate th

5、em in the UK. - This British Standard, having been prepared under the direction of the Sector Board for Materials and Chemicals, was published under the authority of the Standards Board and comes into effect on 16 February 1998 0 BSI 1998 A list of organizations represented on this committee can be

6、obtained on request to its secretaq The responsible UK Technical Committee considers that it is necessary to clarify the combination of figure 1 and the text of subclause 6.1 in respect of a) the orientation of figure 1; b) whether and how compensation should be made to the force to be applied in ac

7、cordance with 6.3 in any arrangement where the weight of the test piece would interact with the specified force. With the operating member now shown in figure 1, vertical and opposite the point of application of the force as required by 6.1.1 in conjunction with a reference to the figure, together w

8、ith the instruction in 6.1.4 to place the test piece the supports S the UK Technical Committee has concluded that for consistency, figure 1 should be regarded as though it is an elevation view with the downward direction towards the top of the page. In this condition, the UK Technical Committee cons

9、iders that the force should be applied at the value specified in accordance with 6.3.1 and item c) of the note to clause 3, with the effect of the weight of the test piece incidentally supplementing that of the applied force. The UK Technical Committee considers that figure 1 should not be presumed

10、to represent an elevation view with the force applied upwards and the test piece restrained by overhead supports, because the effect of the weight of the test piece would then oppose the applied force and undermine the rigour of the test, as well as being inconsistent with 6.1.4. Cross-references Th

11、e British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled International Standards Correspondence Index, or by using the Find facility of the BSI Standards Electronic Catalogue. Warnin

12、g note. This British Standard, which is identical with EN 12100 : 1997, does not necessarily detail all the precautions necessary to meet the requirements of the Health and Safety at Work etc. Act 1974. Attention should be paid to any appropriate safety precautions and the test methods should be ope

13、rated only by trained personnel. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 4, an inside back cover and a back cover. Amendments issued sinc

14、e publication ISBN O 580 29101 4 * * m STD-BSI BS EN L21O-ENGL 1998 R Lb24bb9 Ob82239 221 m EUROPEAN STANDm NORME EUR0PEE”E mTROP b) the number of test pieces to be used (see 5.2); c) the bending force to be applied to the valve (see 6.3.1); d) any test conditions, e.g., test pressure, test duration

15、, which differ from those given in IS0 5.208 : 1993 (see 6.2). Page 3 EN 12100 : 1997 4 Apparatus 4.1 Tensile testing machine or similar appa,mtus, with a device capable of applying a specified force constant to within 2 %. The stationary frame of the machine shall include two supports, S, with a 5

16、mm radius of cumme, having parallel axes and austable spacing (see figure 1). Depending upon the type of valve, the moving part of the machine shall make contact via a tool having a 5 mm radius or a semi-cylindrical face or a yoke, the axis of which is parallel to that of the supports. The tool and

17、the supports shall be made of hardened steel. NOTE. The force should not be applied directly on the body of the valve, so as not to create any damage on the obturating mechanism. The apparatus shall include force and deflection measuring indicators conforming to accuracy class II in accordance with

18、EN 45501 : 1992. 4.2 Torque measuring device, accurate to 5 % (e.g. a torque wrench). 4.3 Compressed air supply, O mbar to 50 mbarl) (O MPa to 0,005 ma), with a pressure regulator. 4.4 Pressure gauge, O mbar to 50 mbar (O MPa to 0,005 MPa), conforming to accuracy class 1,6 in accordance with prEN 83

19、7-1 : 1994. 4.6 Leak detecting danke, accurate to within 0,l cm3/h, (typically with a capacity of 35 cm3) and graduated to enable measurement of volumes of 0,l cm3 (e.g. having a graduated tube with a conical base). 4.6 Airtight piping systems, equipped with the a) fittings for connecting to the pip

20、e sections; b) shut-off devices enabling the valve to be connected to the compressed air supply and the leakdetecting device e.g. pressure gauge (4.4) and gradmed tube (4.5). following: 5 Test pieces 6.1 Preparation The test piece shall comprise a complete vaive, obtained by sampling in accordance w

21、ith the referring standard, assembled between two lengths of PE pipe, each having a length such that the overall length of the test piece can be supported (see 6.1.3). The valve ends shall be fitted with plugging or capping devices (4.6). 5.2 Number The number of test pieces shall be as specified in

22、 the referring standard. 1 1 bar = lo5 N/m2 O BSI 1998 Page 4 EN 12100 : 1997 6 Procedure 6.1 Arrangements 6.1.1 Carry out the following procedure (6.1.2 to 6.3.6 inclusive), by successively placing the valve operating member: - verti, and opposite the point of application of the force (see figure i

23、), then - horizonm, and perpendicular to the direction of the force. 6.1.2 Note the ambient temperature at the start of the test. 6.1.3 Separate the machine frame supports by 10 d, (see figure 1). 6.1.4 Place the test piece on the supports, S, so that the middle of the Valve body under test is equid

24、istant from the two supports and its longitudinal axis is perpendicular to the tool axis and the operating member placed in one of the positions specied in 6.1.1. 6.1.6 Connect the valve assembly to the piping system and install the leakdetecting device downstream from the asemby 6.2 Initial charact

25、eristics Check and record the leaktghtness when the valve is half+pen (shell test) and when it is closed (obturator tightness test) by testing in accordance with Is0 5208 : 1993 and any associated test conditions specified in the referring standard. Measure and record the actuation torque in accorda

26、nce with EN 28233 : 1991. 6.3 Characteristics with the force applied 6.3.1 Apply to the vaive, the force specified in the referring standard at a speed of 25 mmhnin f 10 % (see 4.1). 6.3.2 Mahtain the force, F, on the valve for 10 h, during which time: a) check and record in accordance with Is0 5208

27、 : 1993 the tightness when the valve is open (internal) or haif open (external); b) measure and record the actuation torque in accordance with EN 28233 : 1991; c) if and when an internal or extemal leak or a rupture appears, record the details, including, if possible, its location(s) and report the

28、results in accordance with clause 7. Otherwise proceed in accordance with 6.3.3 to 6.3.6. 6.3.3 Measure and record the amount of deflection present. Release the force F on the valve. 6.3.4 Examine the appearance of the valve and its connecting pipe sections and record any deformation. 6.3.6 Repeat t

29、he procedure given in 6.1.2 to 6.3.4 inclusive, by setting the operating member in the other position specified in 6.1.1. When this has been completed, proceed in accordance with 6.4. 6.4 Final characteristics after removing the force Repeat the procedure given in 6.2. 7 %st report The test report s

30、hall include the following information: a) the reference to this standard and to the referring Stank b) the complete identification of the test piece; c) the type of material, d) the nominal size of the valve; e) the number of test pieces tested; f) whether or not any loss of internai andor external

31、 tightness was observed and the position(s) thereof; g) the torque values, measured in accordance with 6.2, 6.3.2 and 6.4 h) any factors which may have affected the results, such as any incidents or any operating detaiis not specified in this stan Fax: 0181 996 7001. in response to orders for intern

32、ational standads, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library, the Standar

33、dline Database, the BSI Information Technology Service (BIS) and its Technical Help to Exporters Service. Contact the information Department at Chiswick Tel: 0181 996 7111; Fax: 0181 996 7048. Subscribing members of BSI are kept up to date with stan- developments and receive substantial discounts on

34、 the purchase price of standards. For details of these and other benefits contact Customer Services, Membemhip at Chiswick Tel: 0181 996 7002; Fax: 0181 996 7001. Copyright Copyright subsists in ali BSI publications. BSI also holds the copynght, in the UK, of the publications of the intedonal standa

35、rdization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no e-t may be reproduced, stored in a retrieval system or trmsmilted in any form or by any means - electronic, photocopying, recording or otherwise - without prior written permission from BSI. This does not precl

36、ude the he use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grae designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained if permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copynght Manager, MI, 389 CMck High Road, London W4 4AL