EN 1096-4-2004 en Glass in building - Coated glass - Part 4 Evaluation of conformity Product standard《建筑玻璃 镀膜玻璃 第4部分 一致性评估 产品标准》.pdf

《EN 1096-4-2004 en Glass in building - Coated glass - Part 4 Evaluation of conformity Product standard《建筑玻璃 镀膜玻璃 第4部分 一致性评估 产品标准》.pdf》由会员分享，可在线阅读，更多相关《EN 1096-4-2004 en Glass in building - Coated glass - Part 4 Evaluation of conformity Product standard《建筑玻璃 镀膜玻璃 第4部分 一致性评估 产品标准》.pdf（42页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS EN 1096-4:2004 Glass in building Coated glass Part 4: Evaluation of conformity/Product standard The European Standard EN 1096-4:2004 has the status of a British Standard ICS 81.040.20 BS EN 1096-4:2004 This British Standard was published under the authority of the Standards Polic

2、y and Strategy Committee on 20 October 2004 BSI 20 October 2004 ISBN 0 580 44630 1 National foreword This British Standard is the official English language version of EN 1096-4:2004. The UK participation in its preparation was entrusted by Technical Committee B/520, Glass and glazing in building, to

3、 Subcommittee B/520/1, Glass and glazing in building Basic and transformed glass products, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or Eu

4、ropean publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include

5、 all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquirie

6、s on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 39 and a back cove

7、r. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM EN10964 October2004 ICS81.040.20 Englishversion GlassinbuildingCoatedglassPart4:Evaluationof co

8、nformity/Productstandard VerredanslaconstructionVerrecouchePartie4: Evaluationdelaconformit/Normedeproduit GlasimBauwesenBeschichtetesGlasTeil4: Konformittsbewertung/Produktnorm ThisEuropeanStandardwasapprovedbyCENon27May2004. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipu

9、latetheconditionsforgivingthisEurope an Standardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheCentralSecretariatortoanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,Fren

10、ch,German).Aversioninanyotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheCentralSecretariathasthesamestatusast heofficial versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,Cyprus,CzechRepublic,Denmark,Estonia,Finland,France, Germany

11、,Greece,Hungary,Iceland,Ireland,Italy,Latvia,Lithuania,Luxembourg,Malta,Netherlands,Norway,Poland,Portugal, Slovakia, Slovenia,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050B

12、russels 2004CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.EN10964:2004:EEN 1096-4:2004 (E) 2 Contents Page Foreword. 4 1 Scope 5 2 Normative references . 5 3 Terms, definitions and symbols 6 3.2 Symbols . 7 4 Requirements 7 4.1 Product description 7

13、 4.2 Conformity with the definition of coated glass8 4.3 Determination of the characteristics performances. 8 4.3.1 Characteristic of coated glass. 8 4.3.2 Determination of characteristics of coated glass 10 4.4 Durability 12 4.5 Dangerous substances. 12 5 Evaluation of conformity 12 5.1 General. 12

14、 5.2 Initial type testing of the product (see 5.1, 2). 13 5.2.1 General. 13 5.2.2 Initial type testing of coated glass 14 5.2.3 Initial type testing of characteristics performances. 15 5.3 Factory production control and inspection of samples in accordance with a prescribed test plan (see 5.1, 1a and

15、 b) 15 5.4 Initial inspection of factory and of factory production control (see 5.1, 1c). 16 5.5 Continuous surveillance and assessment of the factory production control (see 5.1, 1c) 17 6 Marking and/or labelling. 17 6.1 General. 17 6.2 Product marking 17 6.3 Product characteristics 17 6.4 “Charact

16、eristics/performance identification paper” . 18 7 Initial type testing; sampling and measurement of photometric and energy characteristics. 18 7.1 Sampling 18 7.1.1 General. 18 7.1.2 Sample specification 18 7.2 Measurement of photometric and energy characteristics 18 Annex A (normative) Factory prod

17、uction control 20 A.1 Factory Production Control Requirements 20 A.1.1 General. 20 A.1.2 Organisation 20 A.1.3 Control system 20 A.2 Marking 21 A.3 Inspection and testing tables of coated glass product production. 21 A.3.1 Information on Tables A.1 and A.2 21 A.3.2 Comments specific to Table A.1 22

18、A.3.3 Comments specific to Table A.2 23 A.3.4 Use of proxy testing 23 Annex B (informative) Tests for factory production control 28 EN 1096-4:2004 (E) 3 B.1 General. 28 B.2 Radiometric properties. 28 B.2.1 Sampling 28 B.2.2 Measurements . 28 B.3 Information on ensuring durability conformity 29 Annex

19、 C (informative) Provisions for voluntary involvement of third party(ies) . 30 C.1 General . 30 C.2 Voluntary tasks for third parties 30 C.3 Marking and labelling 30 (informative) Clauses of this European Standard addressing the provisions of EU Construction Products Directive. 31 ZA.1 Scope and rel

20、evant characteristics. 31 ZA.2 Procedure(s) for the attestation of conformity of coated glass products 33 ZA.2.1 System(s) of attestation of conformity . 33 ZA.2.2 EC Certificate and Declaration of conformity 35 ZA.3 CE marking and labelling . 37 Bibliography . 39 EN 1096-4:2004 (E) 4 Foreword This

21、document (EN 1096-4:2004) has been prepared by Technical Committee CEN/TC TC 129 “Glass in building”, the secretariat of which is held by IBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April

22、 2005, and conflicting national standards shall be withdrawn at the latest by July 2006. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU D

23、irective(s), see informative Annex ZA, B, C or D, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, De

24、nmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. No existing document is superseded. This part of the document does not s

25、tand-alone, it is a part of one document: EN 1096-1, Glass in building Coated glass - Part 1: Definitions and classification EN 1096-2, Glass in building - Coated glass - Part 2: Requirements and test methods for class A, B and S coatings EN 1096-3, Glass in building - Coated glass - Part 3: Require

26、ments and test methods for class C and D coatings EN 1096-4, Glass in building - Coated glass - Part 4: Evaluation of conformity/Product standard This document contains other aspects of importance of trade. EN 1096-4:2004 (E) 5 1 Scope This document covers the evaluation of conformity and the factor

27、y production control of coated glass for use in buildings. Note: For glass products with electrical wiring or connections for, e.g. alarm or heating purposes, other directives, e.g. Low Voltage Directive, may apply. 2 Normative references The following referenced documents are indispensable for the

28、application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 356, Glass in building - Security glazing - Testing and classification of resistance against manual attack

29、EN 410, Glass in building - Determination of luminous and solar characteristics of glazing EN 572-1, Glass in building Basic soda lime silicate glass products - Part 1: Definitions and general physical and mechanical properties EN 572-2, Glass in building Basic soda lime silicate glass products - Pa

30、rt 2: Float glass EN 572-3, Glass in building Basic soda lime silicate glass products - Part 3: Polished wired glass EN 572-4, Glass in building Basic soda lime silicate glass products - Part 4: Drawn sheet glass EN 572-5, Glass in building Basic soda lime silicate glass products - Part 5: Patterned

31、 glass EN 572-6, Glass in building Basic soda lime silicate glass products - Part 6: Wired patterned glass EN 572-7, Glass in building Basic soda lime silicate glass products - Part 7: Wired or unwired channel shaped glass EN 673, Glass in building Determination of thermal transmittance (U value) Ca

32、lculation method EN 1063, Glass in building - Security glazing - Testing and classification of resistance against bullet attack EN 1096-1, Glass in building - Coated glass - Part 1: Definitions and classification EN 1096-2, Glass in building - Coated glass - Part 2: Requirements and test Methods for

33、 class A, B and S coatings EN 1096-3, Glass in building - Coated glass - Part 3: Requirements and test methods for class C and D coatings EN 1748-1-1, Glass in building - Special basic products - Borosilicate glasses Part 1-1: Definition and general physical and mechanical properties EN 1748-2-1, Gl

34、ass in building - Special basic products - Glass ceramics Part 2-1: Definitions and general physical and mechanical properties EN 1863-1, Glass in building Heat strengthened soda lime silicate glass Part 1: Definition and description EN 1096-4:2004 (E) 6 EN 12150-1, Glass in building Thermally tough

35、ened soda lime silicate safety glass Part 1: Definition and description EN 12337-1, Glass in building Chemically strengthened soda lime silicate glass - Part 1: Definition and description EN ISO 12543-1, Glass in building Laminated and laminated safety glass - Part 1: Definitions and description of

36、component parts (ISO 12543-1:1998) EN 12600, Glass in building - Pendulum test - Impact test method and classification for flat glass EN 12758, Glass in building - Glazing and airborne sound insulation Product descriptions and determination of properties EN 12898, Glass in building - Determination o

37、f the emissivity EN 13024-1, Glass in building Thermally toughened borosilicate safety glass - Part 1: Definition and description prEN 13474, Glass in building Design of glass panes EN 13501-1, Fire classification of construction products and building elements Part 1: Classification using test data

38、from reaction to fire tests EN 13501-2, Fire classification of construction products and building elements Part 2: Classification using data from fire resistance tests, excluding ventilation services prEN 13501-5, Fire classification of construction products and building elements - Part 5: Classific

39、ation using data from fire exposure roof tests EN 13541, Glass in building - Security glazing - Testing and classification of resistance against explosion pressure EN 14178-1, Glass in building - Basic earth alkaline silicate glass products Part 1: Float glass prEN 14179-1, Glass in building Heat so

40、aked thermally toughened soda lime silicate safety glass Part 1 Definition and description prEN 14321-1, Glass in building Thermally toughened alkaline earth silicate safety glass Part 1: Definition and description 3 Terms, definitions and symbols 3.1 Terms and definitions For the purpose of this do

41、cument, the terms and definitions given in EN 1096-1, 2 and 3 and the following apply: 3.1.1 initial type testing determination of the performance of a product (characteristic, durability), on the basis of either actual tests or other procedures (such as conventional, standardised, tabulated or gene

42、ral accepted values, standardised or recognised calculation methods, test reports when made available, ), in accordance with this document that demonstrates compliance with this document EN 1096-4:2004 (E) 7 3.1.2 test report document that covers the results of tests undertaken on a representative s

43、ample of the product from production or on a prototype design of the product 3.1.3 product description document that details the relevant parameters, e.g. process conditions, structure, etc., for defining a product that complies with the standard. It includes specific reference(s) to characteristics

44、 that are modified by the production process 3.1.4 significant change variation in performance beyond the permitted tolerance for the characteristic 3.2 Symbols and emissivity of both sides of a coated glass pane vlight transmittance vand v light reflectance of both sides of a coated glass pane eene

45、rgy transmittance eand e energy reflectance of both sides of a coated glass pane iemissivity of a test specimen measured during factory production control Additional subscripts: d indicates that the value is a declared value m indicates that the value is a determined value obtained by measurement, c

46、alculation or other means 4 Requirements 4.1 Product description For conformity purposes, the coated glass manufacturer 1is responsible for the preparation and maintenance of a product description. This description shall describe the product and/or product family. Disclosure of the product descripti

47、on shall be at the discretion of the coated glass manufacturer or his agent except in the case of regulatory requirements. The description shall contain at least a normative part. The description may also contain an informative part, when the manufacturer foresees further development of the product.

48、 1The terms manufacturer and producer are understood as being synonyms (see CPD working document NB-CPD/02/019 issued 24 April 2002 page 1) EN 1096-4:2004 (E) 8 The normative part of the description shall contain the following: Reference to EN 1096 Parts 1, 2 and 3 and all other standards with which the manufacturer claims compliance. Type of coating, i.e. on-line, off-line. Method of coating deposition, e.g. chemical-vapour deposition, sputtering, etc. The materials