DLA SMD-5962-95698 REV C-2004 MICROCIRCUIT HYBRID LINEAR 15-VOLT SINGLE CHANNEL DC-DC CONVERTER《15伏特单通道直流电和直流电转换器线型混合微电路》.pdf

《DLA SMD-5962-95698 REV C-2004 MICROCIRCUIT HYBRID LINEAR 15-VOLT SINGLE CHANNEL DC-DC CONVERTER《15伏特单通道直流电和直流电转换器线型混合微电路》.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-95698 REV C-2004 MICROCIRCUIT HYBRID LINEAR 15-VOLT SINGLE CHANNEL DC-DC CONVERTER《15伏特单通道直流电和直流电转换器线型混合微电路》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add case outlines Y and Z. 99-08-11 Raymond Monnin B Figure 1, case outline X, correct dimensions D and E. 00-08-03 Raymond Monnin C Drawing updated to reflect current requirements. -sld 04-07-27 Raymond Monnin REV SHEET REV SHEET REV STATUS REV

2、C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY Steve Duncan DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Michael C. Jones COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil/ THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVE

3、D BY Kendall A. Cottongim MICROCIRCUIT, HYBRID, LINEAR, 15-VOLT, SINGLE CHANNEL, DC-DC CONVERTER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 96-07-02 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-95698 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E356-04 Provided by IHSNot fo

4、r ResaleNo reproduction or networking permitted without license from IHS-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95698 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes

5、 as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in

6、 the following example: 5962 - 95698 01 H X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devi

7、ces shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 MCH2815S/883, MGH281

8、5S/883 DC-DC converter, 1.5 W, 15 V output 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and

9、 E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in appli

10、cations where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guar

11、antees (but may not test) periodic and conformance inspections (Group A, B, C and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; th

12、erefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature rang

13、e. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95698 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as

14、 designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 7 Dual-in-line Y See figure 1 18 Flat pack Z See figure 1 18 Flat pack with formed leads 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute ma

15、ximum ratings. 1/ Input voltage range -0.5 V dc to +50 V dc Power dissipation (PD). 4.0 W Output power. 1.56 W Lead soldering temperature (10 seconds). +300C Storage temperature range . -65C to +150C 1.4 Recommended operating conditions. Input voltage range +12 V dc to +50 V dc Case operating temper

16、ature range (TC) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited i

17、n the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT

18、OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or www.dodssp.daps.mil or from the Standardization Document Order Desk, 700 Robbins Ave

19、nue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a spec

20、ific exemption has been obtained. 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Except for input voltage transient up to 70 volts for no more than 120 milliseconds. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH

21、S-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95698 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance

22、with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections

23、 herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimen

24、sions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 El

25、ectrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgrou

26、ps specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also

27、be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein

28、. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DSCC-VA) upon request. 3.7 Certificate of

29、 compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certif

30、icate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. QUALITY ASSURANCE PROVISIONS 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as

31、modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, meth

32、od 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, bia

33、ses, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TAas specified in accordance with table I of method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim elec

34、trical parameter tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95698 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISIO

35、N LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Limits Test Symbol Conditions -55C TC +125C VIN= 28 V dc 0.5 V unless otherwise specified Group A subgroups Device type Min Max Unit 1 14.85 15.15 Output voltage VOUT IOUT= 50 mA 2,3 01 14.40 15.60 V dc Output c

36、urrent IOUT VIN= 12 to 50 V dc 1,2,3 01 100 mA 1 150 VOUTripple voltage VRIPIOUT= 100 mA, BW = 10 kHz to 2 MHz 2,3 01 250 mVp-p VOUTline regulation VRLINEIOUT= 100 mA, VIN = 12 V dc to 50 V dc 1,2,3 01 350 mV VOUTload regulation VRLOADIOUT= 10 mA to 100 mA 1,2,3 01 1600 mV IOUT= 0 A, Inhibit (see fi

37、gure 2) = 0 1,2,3 01 3.5 mA Input current IINIOUT= 0 A, Inhibit (see figure 2) = open 1,2,3 01 12 mA 1 200 IINripple current IRIPIOUT= 100 mA, LIN = 2 H BW = 10 kHz to 10 MHz 2,3 01 250 mAp-p 1 01 74 Efficiency Eff IOUT= 100 mA 2,3 01 72 % Isolation ISO Input to output or input to case ground or out

38、put to case ground at 500 V dc, (see figure 2) TC= +25C 1 01 100 M 1 3.7 Short circuit power dissipation PDPIN POUT 2,3 01 4.0 W 4 300 450 Switching frequency FSIOUT= 100 mA 5,6 01 270 470 kHz See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without

39、 license from IHS-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95698 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol Conditions -55C TC +125C VIN= 28 V dc 0.5 V unle

40、ss otherwise specified Group A subgroups Device type Min Max Unit 4 -700 +700 VOUTstep load transient 1/ VTLOAD50% load to/from 100% load 5,6 01 -800 +800 mV pk 4 600 VOUTstep load transient recovery 1/ 2/ 3/ TTLOAD50% load to/from 100% load 5,6 01 750 s VOUTstep line transient 2/ 4/ VTLINEInput ste

41、p 12 V dc to/from 50 V dc, IOUT= 100 mA 4,5,6 01 -850 +850 mV pk VOUTstep line transient recovery 2/ 3/ 4/ TTLINEInput step 12 V dc to/from 50 V dc, IOUT= 100 mA 4,5,6 01 2.5 ms Start up overshoot 2/ VtonOSIOUT= 100 mA, VIN= 0 to 28 V dc 4,5,6 01 450 mV pk Start up delay 3/ 5/ TonDIOUT= 100 mA 4,5,6

42、 01 40 ms Load fault recovery 2/ TrLF4,5,6 01 20 ms Capacitive load 2/ 6/ CL No effect on dc performance, TC= +25C 4 01 200 F 1/ Load step transition time greater than 10 micro-seconds. 2/ Parameter shall be tested as part of device characterization and after design and process changes. Thereafter,

43、parameters shall be guaranteed to the limits specified in table I. 3/ Recovery time is measured from the initiation of the transient until VOUThas returned to within 1 percent of VOUT final value. 4/ Input step transition time greater than 10 micro-seconds. 5/ Start up delay time measurement is eith

44、er for a step application of power at the input or the removal of a ground signal from the inhibit pin (see figure 2) while power is applied to the input. 6/ Capacitive load may be any value from 0 to the maximum limit without compromising dc performance. Provided by IHSNot for ResaleNo reproduction

45、 or networking permitted without license from IHS-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95698 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 Case outline X. Millimeters Inches Symbol Min Max Min Max A 6.86 .270 b 0.41 0.51 .016 .020 b1 1

46、.37 1.47 .054 .058 D 24.89 .980 e 3.30 3.56 .130 .140 e1 5.84 6.10 .230 .240 e2 10.92 11.18 .430 .440 e3 13.46 13.72 .530 .540 e4 21.08 21.34 .830 .840 E 20.45 .805 E1 15.11 15.37 .595 .605 L 7.40 .290 S 2.34 2.60 .092 .102 S1 17.58 17.83 .692 .702 NOTES: 1. The U.S. government preferred system of m

47、easurement is the metric SI. This item was designed using inch- pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule. 2. Pin numbers are for reference only. 3. Device weight: 12 grams maximum. FIGURE 1. Case outl

48、ine(s). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95698 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 Case outline Y. Symbol Millimeters Inches Min Max Min Max A 6.35 .250 b 0.30 0.56 .012 .022 c 0.20 0.41 .008 .016 D 21.84 22.35 .860 .880 E 25.15 25.65 1.095 1.010 e 2.54 BSC 0.100 BSC L 12.70 TYP 0.500 TYP Q 1.78 2.29 .070