DLA SMD-5962-94544 REV D-2012 MICROCIRCUIT HYBRID LINEAR 90-VOLT SYNCHRO TO DIGITAL CONVERTER.pdf

《DLA SMD-5962-94544 REV D-2012 MICROCIRCUIT HYBRID LINEAR 90-VOLT SYNCHRO TO DIGITAL CONVERTER.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-94544 REV D-2012 MICROCIRCUIT HYBRID LINEAR 90-VOLT SYNCHRO TO DIGITAL CONVERTER.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R114-96. 96-04-22 K. A. Cottongim B Update drawing requirements to MIL-PRF-38534. 01-03-16 Raymond Monnin C Rewrite paragraphs 4.2.a.2. and 4.3.3.b.2 to add TC. 04-07-16 Raymond Monnin D Updated drawing paragra

2、phs. -sld 12-08-07 Charles F. Saffle REV SHEET REV SHEET REV STATUS OF SHEETS REV D D D D D D D D D D D SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Gary Zahn DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAWING CHECKED BY Michael C.

3、Jones THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Kendall A. Cottongim MICROCIRCUIT, HYBRID, LINEAR, 90-VOLT, SYNCHRO TO DIGITAL CONVERTER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 95-03-17 AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-94544 SHEET 1

4、 OF 11 DSCC FORM 2233 APR 97 5962-E268-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94544 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scop

5、e. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are ref

6、lected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 94544 01 H X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiat

7、ion hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type

8、 Generic number Circuit function Frequency Accuracy 1 LSB 01 SD-14552DX-112 90 V S/D converter 400 Hz 4 min 02 SD-14554DX-112 90 V S/D converter 60 Hz 4 min 03 SD-14552DX-114 90 V S/D converter 400 Hz 2 min 04 SD-14554DX-114 90 V S/D converter 60 Hz 2 min 1.2.3 Device class designator. This device c

9、lass designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device

10、 class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing versio

11、n of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D).

12、E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) ta

13、ken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without licens

14、e from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94544 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals P

15、ackage style X See figure 1 34 Dual-in-line, staggered pins 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Positive supply voltage (VCC) +7.0 V dc Reference input voltage 130 V rms Digital input voltage range -0.3 V dc to +7.0 V dc Power d

16、issipation, TA = +125 C (PD) 170 mW Thermal resistance junction-to-case (qJC) 8.0 C/W Thermal resistance junction-to-ambient (qJA) 20 C/W Storage temperature range -65 C to +150 C Lead temperature (soldering, 10 seconds) . +300 C 1.4 Recommended operating conditions. Positive supply voltage (VCC) +4

17、.75 V dc to +5.25 V dc Reference input voltage range. 10 V rms to 130 V rms Reference input carrier frequency range: Device types 01 and 03. 360 Hz to 5000 Hz Device types 02 and 04. 47 Hz to 1000 Hz Signal input voltage range 81 V rms to 99 V rms Ambient operating temperature range (TA) -55 C to +1

18、25 C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or cont

19、ract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-H

20、DBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 O

21、rder of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 1/ Stresses above t

22、he absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-9

23、4544 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall

24、include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify, or optimize the tests and inspections herein, however, the performance requirements as defin

25、ed in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensio

26、ns shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Block diagram. The block diagram shall be as specified

27、 on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements

28、shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor s

29、imilar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each devic

30、e type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime

31、 -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the manufacturers product meets the performa

32、nce requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be

33、 in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional cri

34、teria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request. Als

35、o, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA or TC as specified in accordance with table I of method 1015 of MIL-STD-883. b. Interim and final electrical test paramet

36、ers shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-945

37、44 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55 C TA +125 C VCC = +5 V dc, unless otherwise specified Group A subgroups Device type Limits Unit Min Max Resolution control 1/

38、RC A = B = 0.8 V 7,8A,8B All 10 10 Bits A = 2.0 V, B = 0.8 V 12 12 A = 0.8 V, B = 2.0 V 14 14 A = B = 2.0 V 16 16 Accuracy repeatability AR 2/ 3/ 7,8A,8B All -1.0 +1.0 LSB Accuracy differential AD 2/ 3/ 7,8A,8B All -1.0 +1.0 LSB Output accuracy AOUT In 16-bit mode 2/ 7,8A,8B 01,02 -13 +13 LSB 03,04,

39、05 -7 +7 Reference input voltage range 3/ VIN1 4,5,6 All 10 130 V rm s Reference input impedance 3/ ZIN1 Single ended 4,5,6 All 270 kW Differential 540 Reference input common mode range 3/ VCM1 4,5,6 All -200 +200 V pk Signal input common mode range 3/ VCM2 4,5,6 All -180 +180 V pk Signal input impe

40、dance 3/ ZIN2 Line-to-line 4,5,6 All 123 kW Line-to-ground 80 Digital output low voltage 1/ VOL IOL = -1.6 mA 1,2,3 All 0.4 V Digital output high voltage 1/ VOH IOH = 0.4 mA 1,2,3 All 2.8 V Output leakage current 3/ IOZ 1,2,3 All -10 +10 mA See footnotes at end of table. Provided by IHSNot for Resal

41、eNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94544 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55

42、 C TA +125 C VCC = +5 V dc, unless otherwise specified Group A subgroups Device type Limits Unit Min Max Digital input high voltage 1/ VIH Digital inputs A, B, INH, EL, and EM. VIN = 2.0 V 1,2,3 All pass/ fail Digital input low voltage 1/ VIL Digital inputs A, B, INH, EL, and EM. VIN = 0.8 V 1,2,3 A

43、ll pass/ fail Digital input current 1/ IIN EL, EM, INH, A, B, internal pull-up 4,5,6 All -10 mA Inhibit voltage 1/ VINH No digital angles change while INH is logic 0 and analog input is rotating 7,8A,8B All 0.8 V Enable voltage 1/ VE EM controls output bits 1 through 8 and EL controls output bits 9

44、through 16. 7,8A,8B All 0.8 V Disable voltage 1/ (high impedance) VD EM controls output bits 1 through 8 and EL controls output bits 9 through 16. 7,8A,8B All 2.0 V Positive supply voltage ICC VCC = +5.25 V 1,2,3 All +34 mA Analog velocity output voltage VOUT 4/ 7,8A,8B All 2.24 3.36 V Bandwidth 1/

45、BW 7,8A,8B 01,03 39 72 Hz 02,04 9.8 18.2 1/ These parameters are tested on a go-no-go basis only or in conjunction with other measured parameters and are not directly testable. 2/ Output accuracy is measured at angles from 0 , to 180 , in 15 increments, and at 225 , 270 , and 315 . 3/ Parameters sha

46、ll be tested as part of device initial characterization and after design and process changes. Parameter shall be guaranteed to the limits specified in table I for all lots not specifically tested. 4/ Analog output voltage is tested at 8 revolutions per second (rps) for device types 01, 03 and at 1.6

47、 rps for device types 02, 04. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94544 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 Case outline X. Symbol Millim

48、eters Inches Minimum Maxim um Minimum Maxim um A1 - 5.33 - 0.210 b 0.41 0.51 0.016 0.020 b1 1.14 1.40 0.045 0.055 D - 25.40 1.000 D1 20.19 20.45 0.795 0.805 D2 17.65 17.91 0.695 0.705 D3 2.41 2.67 0.095 0.105 D4 1.14 1.40 0.045 0.055 E - 19.81 0.780 E1 15.11 15.37 0.595 0.605 E2 10.03 10.29 0.395 0.405 L1 4.06 - 0.160 - Q1 1.14 1.40 0.045 0.055 Q2 0.1