DLA SMD-5962-89799 REV C-2011 MICROCIRCUIT HYBRID DIGITAL DRIVER RECEIVER SINGLE CHANNEL.pdf

《DLA SMD-5962-89799 REV C-2011 MICROCIRCUIT HYBRID DIGITAL DRIVER RECEIVER SINGLE CHANNEL.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-89799 REV C-2011 MICROCIRCUIT HYBRID DIGITAL DRIVER RECEIVER SINGLE CHANNEL.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes made in accordance with NOR 5962-R121-92. -sld 92-02-10 Alan Barone B Update drawing to the latest requirements -sld 05-11-03 Raymond Monnin C Updated drawing paragraphs. -sld 11-11-09 Charles F. Saffle The original first page of this dra

2、wing has been replaced REV SHEET REV SHEET REV STATUS REV C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY Steve Duncan DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAWING CHECKED BY Gary Zahn TH

3、IS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY William K. Heckman MICROCIRCUIT, HYBRID, DIGITAL, DRIVER/RECEIVER, SINGLE CHANNEL AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 91-06-26 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-89799 SHEET 1 OF 13 DSCC FOR

4、M 2233 APR 97 5962-E050-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89799 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing

5、 describes device requirements for class H hybrid microcircuits to processed in accordance with MIL-PRF-38534. 1.2 PIN. The PIN shall be as shown in the following example: 5962-89799 01 X X Drawing number Device type Case outline Lead finish (see 1.2.1) (see 1.2.2) (see 1.2.3) 1.2.1 Device type(s).

6、The device type(s) identify the circuit function as follows: Coupling transformer Turns ratio Device type Generic number Circuit function Transformer Direct 01 1/ FC 155391 Low power, driver-receiver 0.67:1 0.47:1 02 2/ FC 155392 Low power, driver-receiver 0.67:1 0.47:1 1.2.2 Case outline(s). The ca

7、se outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 24 Dual-in-line 1.2.3 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 3/ Supply voltage range (VCC) . -0.3 V

8、 dc to +7 V dc Logic input voltage range -0.3 V dc to VCCReceiver differential voltage 40 Vp-pReceiver common mode voltage range -10 V dc to +10 V dc Driver peak output current 200 mA Power dissipation (PD) at TC= +125C . 1.4 W Storage temperature range . -65C to +150C Lead temperature (soldering, 1

9、0 seconds) . +300C Junction temperature (TJ) . +160C Thermal resistance, junction-to-case (JC) 18C/W Thermal resistance, junction-to-ambient (JA) . 35C/W 1/ Interfaces with the Harris Manchester encoder/decoder. 2/ Interfaces with Smiths Manchester encoder/decoder. 3/ Stresses above the absolute max

10、imum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89799 DLA LAND A

11、ND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.4 Recommended operating conditions. Supply voltage range (VCC) . +4.5 V dc to +5.5 V dc Logic input voltage range 0 V dc to +5 V dc Receiver differential voltage 30 Vp-pReceiver common mode voltage range -10 V dc

12、to +10 V dc Driver peak output current 220 mA Serial data rate . 1.0 MHz maximum Junction temperature (TJ) . +150C Case operating temperature range (TC) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks

13、 form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARD

14、S MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available

15、 online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this dr

16、awing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements shall be in accordance with MIL-PRF-38534 and as specified herein.

17、3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein and figure 1. 3.2.2 Terminal connections. The terminal connectio

18、ns shall be as specified on figure 2. 3.2.3 Timing waveforms. The timing waveforms shall be as specified on figure 3. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89799 DLA LAND AND MARITIME COLUMBUS, OHIO

19、 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test re

20、quirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 he

21、rein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance

22、inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to

23、the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that

24、 the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. Provided by IHSNot for ResaleNo reproductio

25、n or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89799 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TC+125C 4.5 V dc VCC 5.5

26、V dc unless otherwise specified Group A subgroups Device type Limits Unit Min Max Receiver Input level 1/ VIDifferential input, pin 15 to pin 16 4,5,6 All 40 Vp-p Input common mode voltage range 1/ VICMIndependent of xmfr or in aacordance with MIL-HDBK-1553 section 5.1.2.2 4,5,6 All -10 +10 V(pk) Ou

27、tput low voltage VOLIOL= 16 mA 1,2,3 All 0.5 V Output high voltage VOHIOH= -0.4 mA 1,2,3 All 2.4 V Transmitter Input low voltage VIL1,2,3 All 0.7 V Input high voltage VIH1,2,3 All 2.0 V Input low current IIL VIL= 0.4 V 1,2,3 All -1.6 mA Input high current IIHVIH= 2.7 V 1,2,3 All 0.04 mA Output volta

28、ge VOAcross 35 load 1,2,3 All 6.0 9.0 V(pk) Output noise voltage VONAcross 35 load 4,5,6 All 10 mVp-pReceiver strobe Input low voltage VSIL1,2,3 All 0.7 V Input high voltage VSIH 1,2,3 All 2.0 V Input low current ISILVSIL= 0.4 V 1,2,3 All -1.6 mA Input high current ISIHVSIH= 2.7 V 1,2,3 All 0.04 mA

29、See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89799 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performa

30、nce characteristics - Continued. Test Symbol Conditions -55C TC+125C 4.5 V dc VCC 5.5 V dc unless otherwise specified Group A subgroups Device type Limits Unit Min Max Transmitter inhibit Input low voltage VIIL 1,2,3 All 0.7 V Input high voltage VIIH1,2,3 All 2.0 V Input low current IIIL VSIL= 0.4 V

31、 1,2,3 All -1.6 mA Input high current IIIHVSIH= 2.7 V 1,2,3 All 0.04 mA Power supply Total current ICC-SB Standby mode, VCC= 5.5 V dc 1,2,3 All 45 mA ICC-25 25% duty cycle into 70 load, VCC= 5.5 V dc 1/ 4,5,6 All 170 mA ICC-50 50% duty cycle into 70 load, VCC= 5.5 V dc 4,5,6 All 350 mA ICC-100 100%

32、duty cycle into 70 load, VCC= 5.5 V dc 1/ 1,2,3 All 700 mA Receiver Input resistance RIN1 MHz sine wave 1/ 4,5,6 All 1.6 k Input capacitance CIN1 MHz sine wave, 1/ TC= +25C 4 All 2.0 pF Threshold voltage 2/ VTH 1,2,3 All 0.6 1.2 Vp-pGroup C, end-point electricals 0.6 1.2 See footnotes at end of tabl

33、e. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89799 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Contin

34、ued. Test Symbol Conditions -55C TC+125C 4.5 V dc VCC 5.5 V dc unless otherwise specified Group A subgroups Device type Limits Unit Min Max Transmitter Output resistance, transmitter off ROUT1 MHz sine wave 1/ 4,5,6 All 10 k Output capacitance, transmitter off COUT1 MHz sine wave, 1/ TC= +25C 4 All

35、18 pF Output offset voltage VOSVCC= 5.5 V dc 1/ 3/ 4,5,6 All -90 +90 mV(pk) Peak amplitude variation AVVCC= 4.5 V dc 1/ 4/ 4,5,6 All -15 +15 % Receiver Delay time, input to ouput 1/ tDRDelay time from differential input zero crossing to DATA or DATA , see figure 3 9,10,11 All 300 ns Strobe delay 1/

36、tDSDelay time from strobe rising or falling edge to DATA or DATA , see figure 3 9,10,11 All 200 ns Transmitter Rise time tROutput load = 70, see figure 3 9,10,11 All 100 300 ns Fall time tF100 300 ns Delay time tDTSee figure 3 1/ 9,10,11 All 250 ns Inhibit delay inhibiting tDI-HSee figure 3 1/ 9,10,

37、11 All 500 ns Inhibit delay active tDI-LSee figure 3 1/ 9,10,11 All 450 ns 1/ Parameter shall be tested as part of device initial characterization and after design and process changes. Parameter shall be guaranteed to the limits specified in table I for all lots not specifically tested. 2/ Threshold

38、 is measured in direct coupled mode including the transformer. Threshold is the maximum level on the BUS at which there are no pulses on either receiver output. Divide by 1.4 to obtain threshold in transformer coupled mode. Add 0.14 V in direct coupled mode or 0.10 V in transformer coupled mode to o

39、btain threshold at which no errors are observed when receiver is used with 15530 CMOS Manchester encoder-decoder. 3/ Measured across 70 load, 2.5 s after parity bit mid-bit zero crossing of a 660 s message. 4/ Measured across 70 load, variation of average peak amplitude. Provided by IHSNot for Resal

40、eNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89799 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 Symbol Millimeters Inches Min Max Min Max A 4.82 .190 b .51 .020 D 33.02 1.300 e 2.54 B

41、SC .100 BSC eA 12.70 17.78 .500 .700 E 20.06 .790 L 6.60 .260 S 2.23 .088 S1 2.20 .087 NOTES: 1. The U.S. government preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pou

42、nd units, the inch- pound units shall rule. 2. Lead identification for reference only. FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89799 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-

43、3990 REVISION LEVEL C SHEET 9 DSCC FORM 2234 APR 97 Device types 01 and 02 Case outline X Terminal number Terminal symbol 1 TXDATAOUT 2 TXDATAOUT 3 CASE 4 NO CONNECTION 5 NO CONNECTION 6 NO CONNECTION 7 RXLOGICOUT 8 RXDISABLE 9 GND 10 RXLOGICOUT 11 NO CONNECTION 12 NO CONNECTION 13 NO CONNECTION 14

44、NO CONNECTION 15 RXDATAIN 16 RXDATAIN 17 NO CONNECTION 18 GND 19 NO CONNECTION 20 VCC21 TXINHIBIT 22 TXDATAIN 23 TXDATAIN 24 THERMAL OVERIDE NOTE: Pin 24 is a no connection if thermal override is not employed. FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking

45、 permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89799 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 10 DSCC FORM 2234 APR 97 NOTE: Both inputs “TX DATA IN“ and “TX DATA IN“ must be in the same logic state during off times. Device type 01 FIG

46、URE 3. Timing waveform(s). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89799 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 11 DSCC FORM 2234 APR 97 Device type 02 FIGURE 3. Timing

47、 waveform(s) - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-89799 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 12 DSCC FORM 2234 APR 97 TABLE II. Electrical test requir

48、ements. MIL-PRF-38534 test requirements Subgroups (in accordance with MIL-PRF-38534, group A test table) Interim electrical parameters Final electrical parameters 1*,2,3,4,5,6,9,10,11 Group A test requirements 1,2,3,4,5,6,9,10,11 Group C end-point electrical parameters 1,2,3 End-point electrical parameters for Radiation Hardness Assurance (RHA) devices Not applicab