DLA SMD-5962-87613 REV C-2008 MICROCIRCUIT DIGITAL ADVANCED CMOS DUAL 4-INPUT NAND GATE MONOLITHIC SILICON.pdf

《DLA SMD-5962-87613 REV C-2008 MICROCIRCUIT DIGITAL ADVANCED CMOS DUAL 4-INPUT NAND GATE MONOLITHIC SILICON.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-87613 REV C-2008 MICROCIRCUIT DIGITAL ADVANCED CMOS DUAL 4-INPUT NAND GATE MONOLITHIC SILICON.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update boilerplate to MIL-PRF-38535 requirements. LTG 01-07-17 Thomas M. Hess B Add device class V criteria. Add vendor CAGE F8859. Add device type 03. Add case outline X. Add table III, delta limits. Update the boilerplate to MIL-PRF-38535 requi

2、rements. jak 02-06-19 Thomas M. Hess C Update boilerplate to MIL-PRF-38535 requirements. LTG 08-05-15 Thomas M. Hess REV SHET REV C SHET 15 REV STATUS REV C C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Jeffery Tunstall DEFENSE SUPPLY CENTER COLUMBUS

3、 STANDARD MICROCIRCUIT DRAWING CHECKED BY D. A. DiCenzo COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY N. A. Hauck AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 87-06-22 MICROCIRCUIT, DIGITAL, ADVANCED CMOS, DUAL 4-

4、INPUT NAND GATE, MONOLITHIC SILICON AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-87613 SHEET 1 OF 15 DSCC FORM 2233 APR 97 5962-E311-08 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87613 DEFENSE S

5、UPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and l

6、ead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following examples. For device classes M and Q: 5962 - 87613 01 C A Federal stock c

7、lass designator RHA designator (see 1.2.1) Device type (see 1.2.2)Case outline (see 1.2.4)Lead finish (see 1.2.5) / / Drawing number For device class V: 5962 - 87613 01 V X A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2

8、.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RH

9、A levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54AC20 Dual 4-input NAND gate 02 54AC11020 Dual 4-input NAND gate 03 5

10、4AC20 Dual 4-input NAND gate 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as listed below. Since the device class designator has been added after the original issuance of this drawing, device classes M and Q designators will no

11、t be included in the PIN and will not be marked on the device. Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualifica

12、tion to MIL-PRF-38535 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87613 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The c

13、ase outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line D GDFP1-F14 or CDFP2-F14 14 Flat pack X CDFP3-F14 14 Flat pack 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The le

14、ad finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) -0.5 V dc to +7.0 V dc DC input voltage range (VIN) -0.5 V dc to VCC+0.5 V dc DC output voltage range (VOUT) -0.5 V

15、 dc to VCC+0.5 V dc Clamp diode current (IIK,IOK). 20 mA DC output current (per pin) 50 mA DC VCCor GND current (per pin) . 50 mA Storage temperature range (TSTG) . -65C to +150C Maximum power dissipation (PD) . 500 mW Lead temperature (soldering, 10 seconds). +245C Thermal resistance, junction-to-c

16、ase (JC) . See MIL-STD-1835 Junction temperature (TJ) . +175C 4/ 1.4 Recommended operating conditions. 2/ 3/ 5/ Supply voltage range (VCC) +2.0 V dc to +6.0 V dc Input voltage range 0.0 V dc to VCCOutput voltage range . 0.0 V dc to VCCCase operating temperature range (TC) -55C to +125C Input rise or

17、 fall time (tr, tf): VCC= 3.6 V 0 to 116 ns (10-90 percent, 40 ns/V) VCC= 5.5 V 0 to 88 ns (10-90 percent, 20 ns/V) 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unle

18、ss otherwise noted, all voltages are referenced to GND. 3/ The limits for the parameters specified herein shall apply over the full specified VCCrange and case temperature range of -55C to +125C. 4/ Maximum junction temperature shall not be exceeded except for allowable short duration burn-in screen

19、ing conditions in accordance with method 5004 of MIL-STD-883. 5/ Operation from 2.0 V dc to 3.0 V dc is provided for compatibility with data retention and battery backup systems. Data retention implies no input transition and no stored data loss with the following conditions: VIH 70 percent VCC, VIL

20、 30 percent VCC, VOH 70 percent VCCat -20 A, VOL 30 percent VCCat 20 A. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87613 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4

21、DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the sol

22、icitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT

23、 OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robb

24、ins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents cited in the solicitation or contract. ELECTRONIC INDUSTRIES ALLIAN

25、CE (EIA) JEDEC Standard No. 20 - Standard for Description of 54/74ACXXXXX and 54/74ACTXXXXX Advanced High-Speed CMOS Devices. (Copies of these documents are available online at http:/www.jedec.org or from Electronic Industries Alliance, 2500 Wilson Boulevard, Arlington, VA 22201-3834). 2.3 Order of

26、precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item re

27、quirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described

28、herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in M

29、IL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. T

30、he truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 4. Provided by IHSNot for ResaleNo reproduction or networki

31、ng permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87613 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specifie

32、d herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The e

33、lectrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer

34、 has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1

35、 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certifi

36、cate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK

37、-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the require

38、ments of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notif

39、ication of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs age

40、nt, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by

41、this drawing shall be in microcircuit group number 36 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87613 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION L

42、EVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +3.0 V VCC +5.5 V VCCGroup A subgroups Limits 4/ Unit unless otherwise specified Device type and 3/ Device class Min Max Positive input cl

43、amp voltage 3022 VIC+For input under test, IIN= 1.0 mA All V 0.0 V 1 0.4 1.5 V Negative input clamp voltage 3022 VIC-For input under test, IIN= -1.0 mA All V Open 1 -0.4 -1.5 V 3.0 V 1, 2, 3 2.9 V 4.5 V 1, 2, 3 4.4 VIN= VIHminimum or VILmaximum IOH= -50 A All All 5.5 V 1, 2, 3 5.4 VIN= VIHminimum or

44、 VILmaximum IOH= -12 mA All All 3.0 V 1, 2, 3 2.40 4.5 V 1, 2, 3 3.70 VIN= VIHminimum or VILmaximum IOH= -24 mA All All 5.5 V 1, 2, 3 4.70 High level output voltage 3006 VOH 5/ VIN= VIHminimum or VILmaximum IOH= -50 mA All All 5.5 V 1, 2, 3 3.85 3.0 V 1, 2, 3 0.1 V 4.5 V 1, 2, 3 0.1 VIN= VIHminimum

45、or VILmaximum IOL= 50 A All All 5.5 V 1, 2, 3 0.1 VIN= VIHminimum or VILmaximum IOL= 12 mA All All 3.0 V 1, 2, 3 0.50 4.5 V 1, 2, 3 0.50 Low level output voltage 3007 VIN= VIHminimum or VILmaximum IOL= 24 mA All All 5.5 V 1, 2, 3 0.50 VOL 5/ VIN= VIHminimum or VILmaximum IOL= 50 mA All All 5.5 V 1,

46、2, 3 1.65 3.0 V 1, 2, 3 2.1 V 4.5 V 1, 2, 3 3.15 High level input voltage VIH6/ All All 5.5 V 1, 2, 3 3.85 3.0 V 1, 2, 3 0.9 V 4.5 V 1, 2, 3 1.35 Low level input voltage VIL6/ All All 5.5 V 1, 2, 3 1.65 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitt

47、ed without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87613 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test and MIL-STD-883 test method 1/ Symbol Test conditi

48、ons 2/ -55C TC +125C +3.0 V VCC +5.5 V VCCGroup A subgroups Limits 4/ Unit unless otherwise specified Device type and 3/ Device class Min Max Input leakage current low 3009 IILVIN= 0.0 V All All 5.5 V 1, 2, 3 -1.0 A Input leakage current high 3010 IIHVIN= 5.5 V All All 5.5 V 1, 2, 3 1.0 A Quiescent supply current, output high 3005 ICCHVIN= VCCor GND All All 5.5 V 1, 2, 3 80 A Quiescent supply current, output low 3005 ICCLVIN= VCCor GND All All 5.5 V 1, 2, 3 80 A Input capacitance 3012 CINSee 4.4.1c TC= +25C All Al