DLA SMD-5962-00502 REV D-2013 MICROCIRCUIT HYBRID LINEAR 64 CHANNEL ANALOG MULTIPLEXER.pdf

《DLA SMD-5962-00502 REV D-2013 MICROCIRCUIT HYBRID LINEAR 64 CHANNEL ANALOG MULTIPLEXER.pdf》由会员分享，可在线阅读，更多相关《DLA SMD-5962-00502 REV D-2013 MICROCIRCUIT HYBRID LINEAR 64 CHANNEL ANALOG MULTIPLEXER.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device type 02. -gjc. 03-03-13 Raymond Monnin B Update drawing to the latest requirements. -sld 07-03-27 Robert M. Heber C Made changes to paragraphs 1.3 and 1.4 along with footnote 3, sheet 3. Table I, made corrections to Supply currents tes

2、t, Address input currents test, Enable input current tests, Output leakage current tests, and the Switching tests. Changed footnote 1 to add power supply turn on sequence. Made corrections to Figures 2, 3, 4, and 5. -sld 10-05-05 Charles F. Saffle D Added radiation hardness assurance requirements. T

3、able I: sheet 6, under the Group A subgroups column added footnote 4 for the Address input currents and Enable input current tests. Table I: sheet 7, under the Group A subgroups column added footnote 4 for all current tests. Updated drawing paragraphs. -sld 13-05-06 Charles F. Saffle REV SHEET REV D

4、 D D D D D D SHEET 15 16 17 18 19 20 21 REV STATUS REV D D D D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Gary Zahn DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAWING CHECKED BY Greg Cecil TH

5、IS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Raymond Monnin MICROCIRCUIT, HYBRID, LINEAR, 64 CHANNEL, ANALOG MULTIPLEXER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 02-11-14 AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-00502 SHEET 1 OF 21 DSCC FORM 2233

6、 APR 97 5962-E397-13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00502 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing docum

7、ents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.

8、2 PIN. The PIN shall be as shown in the following example: 5962 F 00502 01 K X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assuranc

9、e (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circu

10、it function 01 ACT8500 64 channel analog multiplexer, high impedance analog input with ESD protection, 32 channels Voltage, 32 channels Voltage and Current 02 ACT8501 64 channel analog multiplexer, high impedance analog input with ESD protection 1.2.3 Device class designator. This device class desig

11、nator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Dev

12、ice performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the s

13、tandard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designat

14、es devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will n

15、ot adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS

16、-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00502 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package sty

17、le X See figure 1 96 Ceramic quad flat pack 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Positive supply voltage between +VEEand GND +16.5 V dc Negative supply voltage between -VEEand GND -16.5 V dc VREFto GND +16.5 V dc Digital input ov

18、ervoltage range: VEN(pins 5, 6, 91, and 92) . ( GND - 4)V VA(pins 1, 3, 93, and 95). ( GND - 4)V VB(pins 2, 4, 94, and 96). ( GND - 4)V Analog input overvoltage range -18 V dc VS +18 V dc Power dissipation (PD), TC = -55nullC to +125C: Device type 01 . 99 mW Device type 02 . 66 mW Thermal resistance

19、 junction-to-case (JC) . 5.5C/W 2/ Storage temperature . -65C to +150C Lead temperature (soldering, 10 seconds) . +300C 1.4 Recommended operating conditions. Positive supply voltage (+VEE) +15 V dc 3/ Negative supply voltage (-VEE) -15 V dc 3/ VREF. +5 V dc 3/ Logic low level voltage (VAL) . +0.8 V

20、dc Logic high level voltage (VAH) . +4.0 V dc Case operating temperature range (TC) -55C to +125C 1.5 Radiation features. 4/ Maximum Total Ionizing Dose (TID) (dose rate = 50 - 300 rad(Si)/s) . 300 krad(Si) 5/ 6/ Enhanced Low Dose Rate Sensitvity (ELDRS) 150 krad(Si) 5/ Single Event Phenomenon (SEP)

21、 effective linear energy transfer (LET): Single Event Latchup (SEL) Immune 5/ Single Event Upset (SEU) . 86 MeV-cm2/mg 7/ Single Event Transient (SET) 86 MeV-cm2/mg 7/ 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels ma

22、y degrade performance and affect reliability. 2/ Based on the maximum power dissipation spread over all six die. 3/ Recommended power supply turn on sequence : +VEE, -VEE, followed by VREF. 4/ See section 4.3.5 for the manufacturers radiation hardness assurance analysis and testing. 5/ The only acti

23、ve element in these devices are purchased as SMD 5962F9563002V9A which assures TID, ELDRS, and SEL. 6/ The package in this drawing is a larger version of the same type (flat package) as the one in SMD 5962-95630, the lid underside is nickel plate (no gold), and RGA data shows negligible amounts of h

24、ydrogen. 7/ SEU and SET testing performed at 86 MeV-cm2/m with no upsets or single event transients. These devices will be re-tested after design or process changes that can affect RHA response of these devices. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

25、m IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00502 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part o

26、f this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883

27、- Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/q

28、uicksearch.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing

29、in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL

30、-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requir

31、ements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and ph

32、ysical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Truth table(s). The truth table(s) shal

33、l be as specified on figure 3. 3.2.4 Switching waveform(s). The switching waveform(s) shall be as specified on figure 4. 3.2.5 Block diagram. The block diagram shall be as specified on figure 5. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance

34、 characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Markin

35、g of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

36、m IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00502 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the

37、electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under

38、document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compli

39、ance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microci

40、rcuits delivered to this drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00502 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical perfo

41、rmance characteristics. Test Symbol Conditions 1/ 2/ -55C TC +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Supply currents +IEEVEN(0-63)= VA(0-3)= VB(0-3)= 0 1,2,3 01 0.3 3 mA 02 0.2 2 -IEE VEN(0-63)= VA(0-3)= VB(0-3)= 0 1,2,3 01 -3 -0.3 mA 02 -2 -0.2 +ISBY VEN(0

42、-63)= 4 V, VA(0-3)= VB(0-3)= 0 3/ 1,2,3 01 0.3 3 mA 02 0.2 2 -ISBY VEN(0-63)= 4 V, VA(0-3)= VB(0-3)= 0 3/ 1,2,3 01 -3 -0.3 mA 02 -2 -0.2 Address input currents IAL(0-3)BVB= 0 V 2/ 1,2,3 4/ 01,02 -2 2 A IAH(0-3)B VB= 5 V 2/ 1,2,3 4/ 01,02 -2 2 A IAL(0-3)A VA= 0 V 2/ 1,2,3 4/ 01 -4 4 A 02 -2 2 IAH(0-3

43、)A VA= 5 V 2/ 1,2,3 4/ 01 -4 4 A 02 -2 2 Enable input current IENL(0-15) VEN(0-15)= 0 V 1,2,3 4/ 01,02 -1 1 A IENH(0-15)VEN(0-15)= 5 V 1,2,3 4/ 01,02 -1 1 A IENL(16-31)VEN(16-31)= 0 V 1,2,3 4/ 01,02 -1 1 A IENH(16-31)VEN(16-31)= 5 V 1,2,3 4/ 01,02 -1 1 A IENL(32-47)VEN(32-47)= 0 V 1,2,3 4/ 01 -2 2 A

44、 02 -1 1 IENH(32-47)VEN(32-47)= 5 V 1,2,3 4/ 01 -2 2 A 02 -1 1 IENL(48-63)VEN(48-63)= 0 V 1,2,3 4/ 01 -2 2 A 02 -1 1 IENH(48-63)VEN(48-63)= 5 V 1,2,3 4/ 01 -2 2 A 02 -1 1 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

45、STANDARD MICROCIRCUIT DRAWING SIZE A 5962-00502 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ 2/ -55C TC +125C unless otherwise specified Group A subgroups Device t

46、ype Limits Unit Min Max Positive input leakage current (CH0-CH63) +ISOFFOUTPUT(ALL) VIN= +10 V, VEN= 4 V, output and all unused inputs = -10 V 5/ 6/ 1,2,3 4/ 01,02 -100 +700 nA +ISOFFCURRENT(ALL) VIN= +10 V, VEN= 4 V, output and all unused inputs = -10 V 5/ 6/ 1,2,3 4/ 01,02 -100 +700 nA Negative in

47、put leakage current (CH0-CH63) -ISOFFOUTPUT(ALL) VIN= -10 V, VEN= 4 V, output and all unused inputs = +10 V 5/ 6/ 1,2,3 4/ 01,02 -100 +700 nA -ISOFFCURRENT(ALL) VIN= -10 V, VEN= 4 V, output and all unused inputs = +10 V 5/ 6/ 1,2,3 4/ 01,02 -100 +700 nA Output leakage current outputs (pins 25, 26, 6

48、8, and 70) Currents (pins 67 and 69 Device Type 01 only) +IDOFFOUTPUT(ALL) VOUT= +10 V, VEN= 4 V, output and all unused inputs = -10 V 6/ 7/ 1,2,3 4/ 01,02 -100 +100 nA +IDOFFCURRENT(ALL) VOUT= +10 V, VEN= 4 V, output and all unused inputs = -10 V 6/ 7/ 1,2,3 4/ 01,02 -100 +100 nA -IDOFFOUTPUT(ALL) VOUT= -10 V, VEN= 4 V, output and all unused inputs = +10 V 6/ 7/ 1,2,3 4/ 01,02 -100 +100 nA -IDOFFCURRENT(ALL) VOUT= -10 V, VEN= 4 V, output and all unus