DLA MS25034 REV K-2006 GUARD SWITCH 3 POSITION《3号定位开关防护装置》.pdf

《DLA MS25034 REV K-2006 GUARD SWITCH 3 POSITION《3号定位开关防护装置》.pdf》由会员分享，可在线阅读，更多相关《DLA MS25034 REV K-2006 GUARD SWITCH 3 POSITION《3号定位开关防护装置》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5930 MS25034K 1 February 2006 SUPERSEDING MS25034J 20 Decenber1982 DETAIL SPECIFICATION SHEET GUARD, SWITCH, 3 POSITION This specification is approved for use by all Departments and Agencies of the Department of Defense. The complete requirements for acquiring the switch described herei

2、n shall consist of this specification and the latest issue of MIL-DTL-7703. FIGURE1. Dimensions and configuration. INCH-POUNDProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS25034K 2DASH NO. TYPE PANEL THICKNESS (REF) OPERATING FORCE -1 3- HOLEMOUNT

3、ING .050 TO .081 -2 1-HOLE MOUNTING .050 TO .248 .2 TO 1.5 LB FIGURE.1: Dimensions and configuration Continued Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS25034K 3Inches mm Inches mm Inches mm .003 .08 .093 2.36 .688 17.47 .005 .13 .094 2.39 .7

4、19 18.26 .006 .15 .096 2.44 .750 19.05 .008 .20 .156 3.96 .840 21.34 .010 .25 .240 6.10 .875 22.22 .016 .41 .248 6.30 .906 23.01 .030 .76 .272 6.91 1.062 26.97 .031 .79 .469 11.91 1.562 39.67 .032 .81 .475 12.06 1.635 41.53 .050 1.27 .516 13.11 1.812 46.02 .062 1.57 .625 15.88 2.150 54.61 .081 2.06

5、NOTES: 1. Dimensions are inches. 2. Unless otherwise specifies, Tolerances are .016 on decimals. 3. Material: Steel, commercial, shall be smooth and free from burrs. 4. Finish: Zinc plate, ASTM B 633, type III, or cadmium plate, SAE-AMS-QQ-P-416, type III, with optional supplementary treatment per M

6、IL-C-8514 or DOD-P-15328, black enamel, lusterless, color number 37038 or semigloss, color number 27038, FED-STD- 595 or equivalent. 5. This standard takes precedence over documents referenced herein. 6. Referenced documents shall be of the issue in effect on date of invitations for bid. REQUIREMENT

7、 Guard shall remain in either the open or closed position. Opening the guard shall not change position of the switch contacts. When lever is in upward position, closing guard shall throw lever to the center position. Normal operation of the toggle between the center and down positions shall be possi

8、ble without having to lift the guard Referenced documents MIL-DTL-7703 MIL-C-8514 ASTM-B633 SAE-AMS-QQ-P-416 DOD-P-15328 FED-STD- 595 Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Provided by IHSNot for Resal

9、eNo reproduction or networking permitted without license from IHS-,-,-MS25034K 4Custodians: Preparing activity Army CR DLA CC Air Force 11 (Project 5930-2005-011) Navy AS DLA CC Review activities: Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-