DLA MS9060 REV C-2005 BOLT MACHINE-DOUBLE HEXAGON EXTENDED WASHER HEAD CORROSION AND HEAT RESISTANT STEEL DRILLED 190-32 NS《0 190-32 NS型防腐蚀和耐热钢垫圈顶部加长双重六边形锚杆机》.pdf

《DLA MS9060 REV C-2005 BOLT MACHINE-DOUBLE HEXAGON EXTENDED WASHER HEAD CORROSION AND HEAT RESISTANT STEEL DRILLED 190-32 NS《0 190-32 NS型防腐蚀和耐热钢垫圈顶部加长双重六边形锚杆机》.pdf》由会员分享，可在线阅读，更多相关《DLA MS9060 REV C-2005 BOLT MACHINE-DOUBLE HEXAGON EXTENDED WASHER HEAD CORROSION AND HEAT RESISTANT STEEL DRILLED 190-32 NS《0 190-32 NS型防腐蚀和耐热钢垫圈顶部加长双重六边形锚杆机》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、MS9060C 22 JULY 2005Superseding MS9060B 8 AUGUST 1986 INCH-POUNDMILITARY SPECIFICATION SHEET BOLT, MACHINE-DOUBLE HEXAGON, EXTENDED WASHER HEAD, CORROSION AND HEAT RESISTANT STEEL, DRILLED, .190-32 NS This specification sheet is approved for use by all Departments and Agencies of the Department of D

2、efense. Inactive for new design after 31 DEC 1963. The requirements for acquiring the product described herein shall consist of this specification sheet. 2040.050.040.170R.025.015140 MINTHD RUNOUTIAW AS 3062CHAMFER.031 X 45APPROX.190 (NO. 1O) -32 NSMAJOR DIA. 1810-1870PD .1644 - 1667BSEE REQT 2MINOR

3、 DIA .1487 MAX.225.235.003.006 A(S).011 B45.375.251.243.277MIN.011 BEH19MINMATERIAL INDENTIFICATIONRAISED OR DEPRESSED .010 MAXSPACED AS SHOWN CSK 90.047 4 HOLES EQUALLYTO .0605 MAX636332.003 BSECTION THRU THREAD PROFILEOPTIONAL SHAPE OF HEAD.161.171K TO FULL THD.130.100.260R.015A1735CHAMFER 30TO .2

4、50 4035250250FIGURE 1AMSC N/A 1 of 3 FSC 5306 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9060B Table I. Dash numbers and dimensions.DASH NUMBER L K +.000 -.060 APPROXWEIGHT LBS/100 DASH NUMBER L K +.000 -.060 APPROX WEIGHT LBS/100 -05 .438 1/

5、.95 -23 1.562 .938 1.67 -06 .500 1/ .99 -24 1.625 1.000 1.71 -07 .562 1/ 1.03 -25 1.688 1.062 1.75 -08 .625 1/ 1.07 -26 1.750 1.125 1.79 -09 .688 1/ 1.11 -27 1.875 1.250 1.87 -10 .750 .125 1.15 -28 2.000 1.375 1.95 -11 .812 .188 1.19 -29 2.125 1.500 2.03 -12 .875 .250 1.23 -30 2.250 1.625 2.11 -13 .

6、938 .312 1.27 -31 2.375 1.750 2.19 -14 1.000 .375 1.31 -32 2.500 1.875 2.27 -15 1.062 .437 1.35 -33 2.625 2.000 2.35 -16 1.125 .500 1.39 -34 2.750 2.125 2.43 -17 1.188 .562 1.43 -35 2.875 2.250 2.51 -18 1.250 .625 1.47 -36 3.000 2.375 2.59 -19 1.312 .688 1.51 -20 1.375 .750 1.55 -21 1.438 .812 1.59

7、-22 1.500 .875 1.63 1/ Thread to head. Maximum two incomplete threads. Requirements: 1. Material: Corrosion and heat resistant steel AMS 5732. 2. Threads: Threads in accordance with MIL-S-7742. Incomplete threads not to enter fillet. 3. Dimensioning and tolerancing: Dimensioning and tolerancing shal

8、l be in accordance with ANSI Y14.5M. 4. Fluorescent penetrant inspection: Fluorescent penetrant inspection per ASTM E1417. 5. Surface texture: Surface texture, unless otherwise specified, shall be 125 microinches, except upset head, in accordance with ANSI B46.1. 6. Tolerance: Unless otherwise speci

9、fied, tolerances shall be for linear dimensions .010, angular dimensions 5. 7. Edges: Break sharp edges .003 - .015, unless otherwise specified. 8. Procurement specification: SAE-AS7478. 2Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MS9060B 9. Par

10、t number: The part number shall consist of the basic MS number followed by a dash number from Table I. Example: MS9060-063Dash numberBasic MS number MS9060-06 indicates: Bolt, Machine, CRES, Double Hexagon Extended Washer Head, Drilled; .190-32 NS; Length .500. Notes: 1. All dimensions are in inches

11、. 2. Do not use unassigned part numbers. 3. In the event of a conflict between the text of this standard and the references cited herein, the text of this standard shall take precedence. 4. Referenced government (or non government) documents of the issue listed in that issue of the Department of Def

12、ense Index of Specifications and Standards (DoDISS) specified in the solicitation form a part of this standard to the extent specified herein. 5. This standard was developed cooperatively with the SAE aerospace propulsion division. 6. AS and AMS are SAE publications. 7. Changes from previous issue.

13、Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. MILITARY INTEREST Preparing activity: DLA -IS Custodians: Army - AV (Project 5306-2005-014) Navy - AS NOTE: The activities listed above were interested in this do

14、cument as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.milProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-