DLA MIL-DTL-5755 E-2012 MIRROR REARVIEW NONMAGNETIC GENERAL REQUIREMENTS FOR (FOR AERONAUTICAL USE).pdf

《DLA MIL-DTL-5755 E-2012 MIRROR REARVIEW NONMAGNETIC GENERAL REQUIREMENTS FOR (FOR AERONAUTICAL USE).pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-5755 E-2012 MIRROR REARVIEW NONMAGNETIC GENERAL REQUIREMENTS FOR (FOR AERONAUTICAL USE).pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、INCH POUND MIL-DTL-5755E 2 July 2012 SUPERSEDING MIL-DTL-5755D 30 May 2007 DETAIL SPECIFICATION MIRROR, REARVIEW, NONMAGNETIC, GENERAL REQUIREMENTS FOR (FOR AERONAUTICAL USE) Reactivated after 30 May 2007 and may be used for new and existing design and acquisitions. This specification is approved fo

2、r use by all departments and agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the general requirements for aircraft nonmagnetic rearview mirrors. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this sp

3、ecification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requir

4、ements of the documents cited in sections 3 and 4 of this specification, whether or not they are listed. Comments, suggestions , or questions on this document should be addressed to DLA Aviation-VEB, 8000 Jefferson Davis Highway, Richmond, VA 23297-5616, or e-mailed to STDZNMGTdla.mil. Since contact

5、 information can change, you may want to verify the currency of this address information using the ASSIST database at https:/assist.dla.mil/. AMSC N/A FSC 1680 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-5755E 2 2.2 Government documents.

6、2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. COMMERCIAL ITEM DESCRIPTIONS

7、A-A-113 - Tape, Pressure-sensitive Adhesive. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-130 - Identification Marking of U.S. Military Property. MIL-STD-810 - Environmental Engineering Considerations and Laboratory Tests. MIL-STD-31000 - Technical Data Packages (Copies of these documents are available o

8、nline at https:/assist.dla.mil/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2.2 Other government documents, drawings, and publications. The following other government documents, drawings, and publications form a part of this docum

9、ent to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. NAVAL AIR SYSTEMS COMMAND SD-24 - General Specification for Design and Construction of Naval Aircraft. (Copies of this document are available from Commander,

10、 Naval Air Systems Command, 47123 Buse Road, Air 4.1, Patuxent River, MD 20676.) DRAWINGS 50B6219 - Mirror Assembly - Rear View, Nonmagnetic Type A-2. (Copies of this drawing are available from 542 MSUG/GBMU, 380 Richard Ray Blvd., Suite 104, Robins AFB, GA 31098.) 2.3 Order of precedence. Unless ot

11、herwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtain

12、ed. 3. REQUIREMENTS Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-5755E 3 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection in accordance with 4.3. 3.1.1 Component parts. A rearview vision

13、mirror shall consist of a mirror enclosed in a frame with a mounting bracket. 3.2 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials should be used to the maximum extent possible provided that the material meets or exceeds the o

14、perational and maintenance requirements and promotes economically advantageous life cycle costs. 3.3 General requirements. The requirements for the rearview vision mirror shall be as specified herein and also as specified in SD-24 for Navy procurement and drawing 50B6219 for Air Force procurement. 3

15、.4 Design and construction. The mirror assembly shall be built to withstand the strains, jars, vibrations, and other conditions incident to shipping, storage, installation, and service. 3.4.1 Mirror. The mirror shall be of the first-surface type. The reflecting surface shall be uniform in color and

16、shall be free from stains and defects. 3.4.2 Demagnification. The reduction in image size of demagnification shall be as specified in the acquisition order (see 6.2). 3.4.3 Image. The image shall be sharp and uniform on all parts of the mirror. The image shall be free from any distortion noticeable

17、to the unaided eye under normal daylight conditions. 3.4.4 Reflectivity. The 45-degree specular reflectivity of the mirror surface shall be 50 percent 3 percent of the total visible incident light. 3.4.5 Shatter resistance. The rearview mirror shall be provided with a shatter-resistant backing. The

18、border clinched over the reflecting surface shall not exceed 3/32 inch in width. 3.4.6 Mounting bracket. The portion of the mounting bracket integral or attached to the mirror shall be sufficiently rigid to preclude mirror vibration when the aircraft is in flight. 3.4.7 Corrosion. The mirror surface

19、 shall not tarnish or discolor and the optical qualities shall not be impaired by continued exposure to service conditions. 3.4.8 Abrasion. The reflecting surface shall be sufficiently durable to withstand cleaning with solvents such as cleaning acetone, grain alcohol, an aqueous solution of 1 perce

20、nt to 3 percent detergent such as Aerosol OT, or Orvus paste (or equivalent) followed by drying with a soft cloth. 3.4.9 Humidity. The clarity of the image shall not be affected, the specular reflectivity reduced, or the shatter-resistant backing separated when subjected to the humidity test. 3.4.10

21、 Adhesion of reflecting film. The reflecting film shall not separate from the supporting medium. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-5755E 4 3.5 Interchangeability. All parts having the same manufacturers part number shall be dire

22、ctly and completely interchangeable with each other with respect to installation and performance. Changes in manufacturers part numbers shall be governed by the drawing number requirements of MIL-STD-31000. 3.6 Weight. The weight of the mirror assembly shall not exceed 0.65 ounce per square inch of

23、reflecting surface. 3.7 Performance. The mirror shall meet the performance requirements specified in section 4 when subjected to the applicable tests. 3.8 Identification of product. The mirror assembly shall be marked in accordance with MIL-STD-130. 3.9 Workmanship. The mirror, including all parts a

24、nd accessories, shall be constructed and finished in a thoroughly workmanlike manner. The mirror shall be uniform in quality and shall be free from irregularities or defects that could adversely affect performance or durability. 4. VERIFICATION 4.1 Classification of inspections. The inspection requi

25、rements specified herein are classified as follows: a. First article inspection (see 4.3). b. Conformance inspection (see 4.4). 4.2 Inspection conditions. Unless otherwise specified herein, the temperature and pressure at the time of the test shall be ambient room temperature and pressure. 4.3 First

26、 article inspection. When first article inspection is required (see 3.1), the number of mirrors to be submitted for first article testing shall be as specified (see 6.2). This inspection shall include the examination of 4.5 and the tests of 4.6.1 through 4.6.9. 4.4 Conformance inspection. Conformanc

27、e inspection shall include the examination of 4.5 and the tests of 4.6.7, 4.6.8, and 4.6.9. 4.5 Examination. Each mirror shall be examined for compliance with the requirements specified in 3.3 through 3.9. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-

28、,-,-MIL-DTL-5755E 5 4.6 Tests. 4.6.1 Abrasion. A soft unbleached flannel cloth shall be dusted on the nap side with dry soil that has passed through a 200-mesh sieve. The entire reflecting surface of the mirror shall be rubbed lightly with this cloth for 30 seconds using a rotary motion. This rubbin

29、g cycle shall be repeated 30 times. The reflectivity of the mirror shall not be reduced more than 2 percent as determined by the test of 4.6.9. 4.6.2 Temperature shock. The mirror shall be subjected to the temperature shock test of MIL-STD-810, Method 503. There shall be no separation of the reflect

30、ing film from the supporting medium or other detrimental effects on the serviceability of the mirror. 4.6.3 Humidity. The mirror shall be subjected to the humidity test of MIL-STD 810, Method 507. The clarity of the image shall not be affected and the specular reflectivity shall not be reduced when

31、tested in accordance with paragraphs 4.6.8 and 4.6.9. 4.6.4 Salt fog. The mirror shall be subjected to the salt fog test of MIL-STD-810, Method 509 except the spray shall be for a continuous 50 hours. There shall be no reduction in clarity when subjected to the test of 4.6.8. The reflectivity shall

32、not be reduced more than 2 percent as determined by the test of 4.6.9. The residue remaining on the mirror after completion of the tests shall be removed by cleaning with a soft unbleached Canton flannel cloth before the results of the tests are determined. 4.6.5 Vibration. The mirror shall be subje

33、cted to the vibration test of MIL-STD-810, Method 514, “General Vibration“, procedure. There shall be no detrimental effect on the serviceability of the mirror assembly. 4.6.6 Adhesion of reflecting surface. At the completion of the temperature shock test of 4.6.2, tape conforming to A-A-113, one in

34、ch wide, shall be applied firmly to the reflecting surface and stripped off quickly at room temperature. The mirror shall be examined for detachment of the reflective cologne. 4.6.7 Demagnification. The radius of curvature shall be determined by one of the following options: a. With a dial-type gage

35、 with the plunger near the center of the mirror. b. By three fixed legs that need not be equispread. c. With an accurately formed template. d. With any other means acceptable to the inspector. 4.6.8 Image. Clarity of image shall be determined by viewing with the naked eye the reflection of an object

36、 in the mirror. Examination for noticeable distortion of the image shall be made as the mirror is rotated 45 degrees both to the right and left of the line of sight. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-5755E 6 4.6.9 Reflectivity.

37、The specular reflectivity shall be determined by directing a substantially collimated beam of incandescent light at approximately 45 degrees onto the mirror and directing the fraction of this beam specularly reflected into a receptor that shall have a spectral sensitivity approximating the luminosit

38、y function of the standard observer of the International Commission on Illumination. The fraction of the beam specularly reflected shall be determined either by actual measurement of the incident and reflected beams or by comparison of the beams reflected by the test mirror and with that from a suit

39、able calibrated standard mirror. 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the respo

40、nsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the inventory control points packaging activities within the military service or defense agency, or within the military services system command. Packaging data retrieval is available from the mana

41、ging military departments or defense agencys automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Intended use. The mirrors cover

42、ed by this specification are intended for use in aircraft for rear vision purposes. 6.2 Acquisition requirements. Acquisition documents should specify the following: a. Title, number, and date of this specification. b. The specific issue of individual documents referenced (see 2.2.1 and 2.2.2). c. F

43、irst article sample required (see 3.1). d. Demagnification requirements (see 3.4.2). e. First article sample size (see 4.3). f. Packaging requirements (see 5.1). 6.3 Subject term (key word) listing. demagnification image reflectivity Provided by IHSNot for ResaleNo reproduction or networking permitt

44、ed without license from IHS-,-,-MIL-DTL-5755E 7 6.4 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Custodians: Preparing Activity: Army - AV Navy - AS Air Force - 99 DLA - GS1 (Pro

45、ject 1680-2012-002) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST database at https:/assist.dla.mil/. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-