DLA MIL-DTL-55330 C-2001 CONNECTORS ELECTRICAL AND FIBER OPTIC PACKAGING OF《电连接器和光纤包装》.pdf

《DLA MIL-DTL-55330 C-2001 CONNECTORS ELECTRICAL AND FIBER OPTIC PACKAGING OF《电连接器和光纤包装》.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-55330 C-2001 CONNECTORS ELECTRICAL AND FIBER OPTIC PACKAGING OF《电连接器和光纤包装》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-DTL-55330C8 JUNE 2001SUPERSEDINGMIL-C-55330B13 JULY 1988MILITARY SPECIFICATIONCONNECTORS, ELECTRICAL AND FIBER OPTIC, PACKAGING OFThis specification is approved for use by all Departments and Agencies of the Department of Defense.1. SCOPE1.1 Scope. This specification covers the requirements for

2、the preservation, packing, and containermarking of all types of electrical and fiber optic connectors (including interconnectors, splices, couplers,splitters, mixers, and associated accessories) which are primarily in FSCs 5935, 6005, and 6060 (see 6.1)2. APPLICABLE DOCUMENTS2.1 Government documents

3、.2.1.1 Specification and standards. The following specifications and standards form a part of thisspecification to the extent specified herein. Unless otherwise specified, the issues of these documentsshall be those listed in the issue of the Department of Defense Index of Specifications and Standar

4、ds(DoDISS) and supplement thereto, cited in the solicitation.SPECIFICATIONSFEDERALPPP-B-566 - Boxes, Folding, Paperboard.PPP-B-621 - Boxes, Wood, Nailed and Lock-Corner.PPP-B-676 - Boxes, Setup.AMSC N/A 1 of 9 AREA PACKDISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.

5、Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be ofuse in improving this document should be addressed to: Defense Supply Center Columbus, ATTN:VAI, 3990 East Broad Street, Columbus, OH 43213-1199 by using the self-addressed StandardizationDocument Impro

6、vement Proposal (DD form 1426) appearing at the end of this document or by letter.INCH-POUNDProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55330C2STANDARDSFEDERALFED-STD-123 - Marking for shipment (Civic Agencies).DEPARTMENT OF DEFENSEMIL-ST

7、D-129 - Standard Practice for Military Marking.MIL-STD-202 - Test Methods for Electronic and Electrical Component Parts.MIL-HDBK-774 - Palletized Unit Loads.MIL-STD-2073-1 - Standard Practice for Military Packaging.(Unless otherwise indicated, copies of the above specifications, standards, and handb

8、ooks areavailable from the Defense Printing Service Detachment Office, Standardization Document Order Desk,Building 4D Customer Service, 700 Robbins Avenue, Philadelphia, PA 19111-5094.)2.2 Non-Government publications. The following documents form a part of this document to the extentspecified herei

9、n. Unless otherwise specified, the issues of the documents which are DoD adopted arethose listed in the issue of the DoDISS cited in the solicitation. Unless otherwise specified, the issues ofdocuments not listed in the DoDISS are the issues of the documents cited in the solicitation (see 6.2).AMERI

10、CAN SOCIETY OF QUALITY CONTROL (ASQC)ASQC Z1.4 - Procedures, Sampling and Tables For Inspection By Attributes.(Applications for copies should be addressed to the American Society of Quality Control, 611 EastWisconsin Avenue , Milwaukee, Wisconsin, 53202.)AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI)A

11、NSI/NCSL Z540.1 - Laboratories, Calibration, and Measuring and Test Equipment.(Applications for copies should be addressed to the American National Standards Institute, 11 West42ndStreet, New York, NY 10036.)AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM)ASTM-D1974 - Fiberboard Boxes, Methods of C

12、losing, Sealing, and Reinforcing.ASTM-D3951 - Packaging, Commercial.ASTM-D-3953 - Steel, and Seals, Flat, Strapping.ASTM-D6251 - Natural Wood-Cleated, Panel Board, Shipping Boxes.(Applications for copies should be addressed to the American Society for Testing and Materials, 100Barr Harbor Drive, Wes

13、t Conshohocken, PA 19428-2959.)(Non-Government standards and other publications are normally available from the organizations whichprepare or, which distribute the documents. These documents also may be available in or throughlibraries or other informational services.)Provided by IHSNot for ResaleNo

14、 reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55330C32.3 Order of precedence. In the event of a conflict between the text of this document and thereferences cited herein, the text of this document takes precedence. Nothing in this document, however,supersedes applicable

15、laws and regulations unless a specific exemption has been obtained.3. REQUIREMENTS3.1 General. The packaging terms used herein shall be in accordance with the definitions listed in MIL-STD-129, and MIL-STD-2073-1. The following general requirements apply, as applicable, to militaryor commercial pack

16、aging as well as to shipments to Non-Government activities.3.1.1 Hardware. Mounting brackets, screws, and other hardware accompanying or furnished with theconnectors shall be protected and enclosed within the unit packs in a manner that will not damage theconnectors or the packaging materials. When

17、practical, the hardware should be mounted on eachconnector.3.1.2 Physical protection. Connectors and accessories shall be packaged in a manner that will ensurecompliance with the applicable requirements of MIL-STD-2073-1 as well as those specified herein. Forshipments to non-Government activities, l

18、arge quantity unit packs may be used.3.1.2.1 Contacts, leads, and terminals. Contacts, leads, terminals, and other outward projections shallbe protected by means of container design, noncorrosive die-cut inserts, or other suitable supportingmaterials or devices. If not otherwise protected, protectiv

19、e caps shall be used to prevent damage to thecoupling or accessory connector threads.3.1.2.2 Wrapping and cushioning. Wrapping and cushioning materials shall be noncorrosive and dry.In addition, materials used for fiber optic connectors shall be nonstatic generating and shall not crumble,flake, powd

20、er or shed. Cushioning is not required for accessories.3.1.3 Exterior containers. Exterior containers shall be of minimum tare and cube consistent with theprotection required and shall contain quantities of identical stock numbered or otherwise designated itemsto the greatest extent practicable (see

21、 3.3).3.2 Preservation. Preservation shall be military or commercial, as specified (see 6.2).3.2.1 Military.3.2.1.1 Cleaning. Connectors and accessories shall be cleaned in accordance with MIL-STD-2073-1.3.2.1.2 Drying. Connectors and accessories shall be dried in accordance with MIL-STD-2073-1.3.2.

22、1.3 Preservatives. Contact preservatives shall not be used.3.2.1.4 Unit packs.3.2.1.4.1 Connectors. Unless otherwise specified (see 6.2), and except as specified herein,connectors (both electrical and fiber optic) shall be individually unit packed in accordance with MIL-STD-2073-1, method 41. Electr

23、ical connectors with only gold plated contacts shall be preserved inaccordance with MIL-STD-2073-1, method 31.3.2.1.4.1.1 Connectors with removable contacts. Removable crimp type contacts shall not be installedin the connector insert but shall be placed in a close fitting noncorrosive rigid containe

24、r such as a vial orbox and enclosed within the unit pack. Any spare contacts furnished shall also be within this container.3.2.1.4.1.2 Connectors with grommet sealing plugs. Grommet sealing plugs supplied with variousconnectors shall be placed in an envelope or rigid container and enclosed within th

25、e unit pack.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55330C43.2.1.4.2 Accessories (when acquired separately).3.2.1.4.2.1 Contacts. Unless otherwise specified (see 6.2), contacts shall be unit packed five each inaccordance with MIL-STD-

26、2073-1, method 41.3.2.1.4.2.2 Other accessories. Other accessories such as adapters (mechanical), boots, caps, clamps,covers, elbows, grommet sealing plugs, nuts, rings, and tools shall be unit packed in accordance withMIL-STD-2073-1, method 10. Unit pack quantities for other than one each shall be

27、as specified (see 6.2).3.2.1.4.2.3 Supplementary containers. Connectors and accessories, unit packed as specified in3.2.1.4.1 and 3.2.1.4.2, with a unit pack volume of 30 cubic inches (491.7 cubic centimeters) or more, oran item dimension 4 inches (10.16 centimeters) or longer shall be placed in a s

28、upplementary containerconforming to variety 2 of PPP-B-566 or PPP-B-676.3.2.1.5 Intermediate packs. When the unit pack is a bag of any type or the unit pack is less than 64cubic inches (1,049 cubic centimeters), uniform quantities of connectors or accessories of the same NSNshall be placed in interm

29、ediate containers conforming to variety 2 of PPP-B-566, or variety 2 ofPPP-B-676; or ASTM-D1974, class weather resistant. Alternatively, nonweather or nonwater resistantversions of these containers may be used provided they are overwrapped with waterproof barriermaterials. Intermediate containers sh

30、all contain multiples of five unit packs not to exceed 100 unit packs.No intermediate packs are required when the total quantity shipped to a single destination will result inonly one intermediate pack per shipping container.3.2.2 Commercial. Commercial preservation shall be in accordance with ASTM-

31、D3951.3.3 Packing. Packing shall be level A, B, or minimal, as specified (see 3.1 and 6.2).3.3.1 Level A. Connectors and accessories, preserved as specified in 3.2, shall be packed in woodcontainers conforming to ASTM-D6251, overseas type or PPP-B-621, class 2. Closure and strappingshall be in accor

32、dance with the applicable container specification except that metal strapping shallconform to ASTM-D3953. The requirements for level B packing shall be used when the total quantity of astock numbered connector or accessory for a single destination does not exceed a packed volume of 1cubic foot (0.02

33、832 cubic meter).3.3.2 Level B. Connectors and accessories, preserved as specified in 3.2, shall be packed infiberboard containers conforming to ASTM-D1974, class weather resistant, style optional, and specialrequirements. The requirements for box closure, waterproofing and reinforcing shall be in a

34、ccordancewith ASTM-D1974.3.3.3 Minimal. Connectors and accessories, preserved as specified in 3.2, shall be packed infiberboard containers conforming to ASTM-D1974, class domestic, style optional, and specialrequirements. Closures shall be in accordance with ASTM-D1974.3.3.4 Utilized loads. Unless o

35、therwise specified (see 6.2), unitized loads, commensurate with the levelof packing specified in the contract or purchase order, shall be used whenever total quantities forshipment to one destination equal 40 cubic feet (1.1328 cubic meters) or more. Quantities less than 40cubic feet need not be uni

36、tized. Unitized loads shall be uniform in size and quantities to the greatestextent practicable.3.3.4.1 Level A. Connectors, packed as specified in 3.3.1, shall be unitized on pallets in conformancewith MIL-HDBK-774 with a wood cap (storage aid 5) positioned over each load.3.3.4.2 Level B. Connector

37、s, packed as specified in 3.3.2, shall be unitized as specified in 3.3.4.1,except that weather resistant fiberboard caps (storage aid 4) shall be used in lieu of wood caps.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-55330C53.3.4.3 Minimal

38、. Connectors, packed as specified in 3.3.3, shall be unitized as specified in 3.3.4.2except that the fiberboard caps shall be class domestic.3.4 Marking. The following marking is mandatory for shipments both to U.S. Government and non-Government activities.3.4.1 Standard marking. In addition to any

39、special or other identification marking required by thecontract (see 6.2), each unit, supplementary, intermediate, and exterior container and unitized load shallbe marked in accordance with MIL-STD-129. The complete military or contractors type or Part orIdentifying Number (PIN), as applicable, incl

40、uding the Commercial and Government Entity (CAGE) code,shall be marked on all unit and in intermediate packs in accordance with the identification markingprovisions of MIL-STD-129. When specified in the contract (see 6.2), the marking of domestic shipmentsfor civil agencies shall be in accordance wi

41、th FED-STD-123.3.5 First article and quality conformance inspections. First article and quality conformance inspectionsand tests shall be required as specified in 4.4 and 4.5, respectively. Samples for these tests shall befurnished in accordance with the procedures outlined in 4.4 and 4.5. The perfo

42、rmance of the visual anddimensional inspections, rough handling tests, and leakage tests shall conform to the inspections andtests outlined in 4.6.1, 4.6.2.1, and 4.6.2.2, respectively.3.5.1 Functional requirements.3.5.1.1 Rough handling test (when specified, see 6.2). When packs have been tested in

43、 accordancewith 4.6.2.1, all materials and components comprising each pack shall be free from damage or evidenceof misplacement which might affect the utility of the preservation method or pack. The connectors andassociated accessories within the tested packs shall show no visible signs of damage. W

44、hen specified inthe contract (see 6.2), functional tests in accordance with the group A inspection requirements of theapplicable commodity specification shall be conducted on those connectors subjected to the roughhandling tests to determine freedom from operational malfunction. The examination of t

45、he connectorstested under this group A inspection malfunction. The examination of the connectors tested under thisgroup A inspection shall be in accordance with the visual and mechanical inspection requirementsspecified in the applicable connector commodity specification.3.5.1.2 Leakage test (when a

46、pplicable). When a barrier enclosed unit pack has been tested inaccordance with 4.6.2.2, there shall be no evidence of moisture within the unit pack.3.6 Workmanship. The quality of workmanship shall assure acceptance of the completed preservation,packing, and marking requirements in accordance with

47、the inspections specified in section 4.4. VERIFICATION4.1 Classifications of inspections. All items must meet all requirements of section 3. The inspectionset forth in this specification shall become a part of the contractors overall inspection system or qualityprogram. The absence of any inspection

48、 requirements in the specification shall not relieve the contractorof the responsibility of assuring that all products or supplies submitted to the Government. Foracceptance comply with all requirements of the contract. Sampling in quality conformance does notauthorize submission of known defective

49、material, either indicated or actual, nor does it commit theGovernment to acceptance of defective material.4.1.1 Test equipment and inspection facilities. Test and measuring equipment and inspection facilitiesof sufficient accuracy, quality, and quantity to permit performance of the required inspection shall beestablished and maintained by the contractor. The establishment and maintenance of a calibrationsystem to control the accuracy of the measuring and test equipment shall be in accordance withANSI/NCSL