DLA MIL-DTL-28840 3 F-2013 CONNECTOR ACCESSORIES ELECTRICAL CIRCULAR THREADED HIGH SHOCK HIGH DENSITY SHIPBOARD CLAMPS STRAIN RELIEF 45 OPEN FOR ELECTRICAL CONNECTORS.pdf

《DLA MIL-DTL-28840 3 F-2013 CONNECTOR ACCESSORIES ELECTRICAL CIRCULAR THREADED HIGH SHOCK HIGH DENSITY SHIPBOARD CLAMPS STRAIN RELIEF 45 OPEN FOR ELECTRICAL CONNECTORS.pdf》由会员分享，可在线阅读，更多相关《DLA MIL-DTL-28840 3 F-2013 CONNECTOR ACCESSORIES ELECTRICAL CIRCULAR THREADED HIGH SHOCK HIGH DENSITY SHIPBOARD CLAMPS STRAIN RELIEF 45 OPEN FOR ELECTRICAL CONNECTORS.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、AMSC N/A FSC 5935 DETAIL SPECIFICATION SHEET CONNECTOR ACCESSORIES, ELECTRICAL, CIRCULAR, THREADED, HIGH SHOCK, HIGH DENSITY, SHIPBOARD, CLAMPS, STRAIN RELIEF, 45, OPEN, FOR ELECTRICAL CONNECTORS This specification is approved for use by all Departments and Agencies of the Department of Defense. The

2、 requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-28840. FIGURE 1. Dimensions and configurations. MIL-DTL-28840/3F 7 November 2013 SUPERSEDING MIL-DTL-28840/3E 23 October 2009 INCH-POUND Provided by IHSNot for ResaleNo reproduction or netw

3、orking permitted without license from IHS-,-,-MIL-DTL-28840/3F 2 Shell size designator (see note 3) A thread class 2B B max dia C max closed D max E max Screw size ref. Cable entry min max A (11) .750-20 UNEF 1.028 (26.11) 1.650 (23.60) .929 (23.60) .903 (22.94) .114-40 .177 (4.50) .286 (7.26) B (13

4、) .875-20 UNEF 1.141 (28.98) 1.650 (23.60) .929 (23.60) .977 (24.82) .114-40 .177 (4.50) .286 (7.26) C (15) 1.000-20 UNEF 1.263 (32.08) 1.765 (44.60) 1.056 (26.82) 1.151 (29.24) .114-40 .250 (6.35) .416 (10.57) D (17) 1.125-18 UNEF 1.387 (35.23) 1.874 (47.60) 1.233 (31.32) 1.281 (32.54) .114-40 .291

5、 (7.39) .476 (12.09) E (19) 1.250-18 UNEF 1.513 (38.43) 1.918 (48.72) 1.296 (32.92) 1.406 (35.71) .114-40 .348 (8.84) .626 (15.90) F (23) 1.438-18 UNEF 1.703 (43.26) 1.962 (49.83) 1.358 (34.49) 1.576 (40.03) .134-32 .429 (10.90) .831 (21.11) G (25) 1.562-18 UNEF 1.825 (46.36) 2.006 (50.95) 1.420 (36

6、.07) 1.666 (42.32) .134-32 .523 (13.28) .956 (24.28) H (29) 1.875-16 UN 2.143 (54.43) 2.301 (58.45) 1.634 (41.50) 2.046 (51.97) .134-32 .643 (16.33) 1.081 (27.46) J (33) 2.062-16 UNS 2.329 (59.16) 2.389 (60.68) 1.859 (47.22) 2.209 (56.11) .162-32 .704 (17.88) 1.187 (30.15) NOTES: 1. Dimensions are i

7、n inches. Dimensions apply after plating. 2. Metric equivalents are given for information only. 3. Shell sizes are provided within parentheses for information and are not a part of the designator. FIGURE 1. Dimensions and configurations - Continued. Provided by IHSNot for ResaleNo reproduction or ne

8、tworking permitted without license from IHS-,-,-MIL-DTL-28840/3F 3 REQUIREMENTS: Design and construction: Dimensions and configurations: See figure 1. Interface dimensions shall conform to MIL-DTL-28840. Material and finish: See table I. TABLE I. Material and finish. Material and finish designator M

9、aterial Finish W Aluminum alloy in accordance with ASTM B85/B85M, ASTM B26/B26M, ASTM B108/B108M, ASTM B209, ASTM B211, or ASTM B221 Cadmium plate, olive drab over electroless nickel D Corrosion resistant steel in accordance with ASTM A276, ASTM A473, or ASTM A580/A580M, type 316 Cadmium plate, blac

10、k 1/ F Aluminum alloy in accordance with ASTM B85/B85M, ASTM B26/B26M, ASTM B108/B108M, ASTM B209, ASTM B211, or ASTM B221 Pure electro- deposited aluminum, non-reflective L Nickel fluorocarbon polymer, non-reflective S Zinc nickel, non-reflective N Corrosion resistant steel in accordance with ASTM

11、A276, ASTM A473, or ASTM A580/A580M, type 316 Nickel fluorocarbon polymer, non-reflective R Zinc nickel, non-reflective 1/ Screws and washers shall be passivated in accordance with SAE-AMS2700, type 2. Marking: The strain relief clamp shall be identified with the manufacturers name or trademark and

12、the Part or Identifying Number (PIN). PIN example: M28840/ 3 J W Military designator Specification sheet number Shell size designator Material and finish designator (See table I) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-28840/3F 4 QUAL

13、IFICATION: Two samples in each shell size for which qualification is desired shall be tested in accordance with MIL-DTL-28840. RESTRICTIONS: Material and finish designators W and D are inactive for NAVSEA new design, unless approved by NAVSEA. Changes from previous issue. The margins of this specifi

14、cation are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of thi

15、s document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Referenced documents. In addition to MIL-DTL-28840, this document references the following: ASTM A276 ASTM A473 ASTM A580/A580M ASTM B26/B26M ASTM B85/B85M ASTM B108/B108M ASTM

16、B209 ASTM B211 ASTM B221 SAE-AMS2700 CONCLUDING MATERIAL Custodians: Preparing activity: Army - AT DLA - CC Navy - EC Air Force - 85 DLA - CC (Project 5935-2013-101) Review activities: Army AV, MI Navy - OS, SH, YD Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-